wpa_supplicant: update to version 2.0 and enable SoftAP

https://jira.digi.com/browse/DEL-220 #resolve
https://jira.digi.com/browse/DEL-225 #resolve

Signed-off-by: Javier Viguera <javier.viguera@digi.com>

meta-digi-arm/conf/machine/include/imx-digi-base.inc

@@ -23,5 +23,3 @@ UBOOT_SYMLINK = 'u-boot-${MACHINE}${@base_conditional( "UBOOT_CONFIG_VARIANT", "
 
 # Flash image types
 IMAGE_FSTYPES += "sum.jffs2 ubifs"
-
-PREFERRED_VERSION_wpa-supplicant = "1.0"

meta-digi-arm/conf/machine/include/mxs-digi-base.inc

@@ -15,5 +15,3 @@ EXTRA_IMAGEDEPENDS = "u-boot"
 # At the moment it's failing due to wrong u-boot image
 IMAGE_FSTYPES ?= "tar.bz2"
 IMAGE_FSTYPES += "sum.jffs2 ubifs"
-
-PREFERRED_VERSION_wpa-supplicant = "6ffdc2f"

meta-digi-del/recipes-connectivity/wpa-supplicant/wpa-supplicant-2.0.inc

@@ -0,0 +1,52 @@
+DESCRIPTION = "A Client for Wi-Fi Protected Access (WPA)."
+HOMEPAGE = "http://hostap.epitest.fi/wpa_supplicant/"
+BUGTRACKER = "http://hostap.epitest.fi/bugz/"
+SECTION = "network"
+LICENSE = "BSD"
+LIC_FILES_CHKSUM = "file://../COPYING;md5=ab87f20cd7e8c0d0a6539b34d3791d0e \
+                    file://../README;md5=5cb758942d25f6f61fd4ac388fd446fa \
+                    file://wpa_supplicant.c;beginline=1;endline=12;md5=cba4fa09fa364da845ca546f21008909"
+
+DEPENDS = "libnl openssl"
+
+SRC_URI = "http://hostap.epitest.fi/releases/wpa_supplicant-${PV}.tar.gz \
+           file://defconfig \
+           file://wpa_supplicant.conf \
+           file://wpa-supplicant.sh \
+           file://99_wpa_supplicant"
+
+S = "${WORKDIR}/wpa_supplicant-${PV}/wpa_supplicant"
+
+do_configure () {
+	echo "CFLAGS +=\"-I${STAGING_INCDIR}/libnl3\"" >> ${WORKDIR}/defconfig
+	install -m 0644 ${WORKDIR}/defconfig .config
+}
+
+export EXTRA_CFLAGS = "${CFLAGS}"
+export BINDIR = "${sbindir}"
+
+do_compile () {
+	unset CFLAGS CPPFLAGS CXXFLAGS
+	oe_runmake
+}
+
+do_install () {
+	install -d ${D}${sbindir}
+	install -m 0755 wpa_supplicant ${D}${sbindir}
+	install -m 0755 wpa_cli ${D}${sbindir}
+
+	install -d ${D}${bindir}
+	install -m 0755 wpa_passphrase ${D}${bindir}
+
+	install -d ${D}${sysconfdir}
+	install -m 0600 ${WORKDIR}/wpa_supplicant.conf ${D}${sysconfdir}/wpa_supplicant.conf
+
+	install -d ${D}${sysconfdir}/network/if-pre-up.d/
+	install -d ${D}${sysconfdir}/network/if-post-down.d/
+	install -d ${D}${sysconfdir}/network/if-down.d/
+	install -m 0755 ${WORKDIR}/wpa-supplicant.sh ${D}${sysconfdir}/network/if-pre-up.d/wpa-supplicant
+	cd ${D}${sysconfdir}/network/ && ln -sf ../if-pre-up.d/wpa-supplicant if-post-down.d/wpa-supplicant
+
+	install -d ${D}/etc/default/volatiles
+	install -m 0644 ${WORKDIR}/99_wpa_supplicant ${D}/etc/default/volatiles
+}

meta-digi-del/recipes-connectivity/wpa-supplicant/wpa-supplicant-6ffdc2f/wpa_supplicant.conf-sane

@@ -1,7 +0,0 @@
-ctrl_interface=/var/run/wpa_supplicant
-ctrl_interface_group=0
-update_config=1
-
-network={
-        key_mgmt=NONE
-}

meta-digi-del/recipes-connectivity/wpa-supplicant/wpa-supplicant.inc

@@ -1,80 +0,0 @@
-DESCRIPTION = "A Client for Wi-Fi Protected Access (WPA)."
-HOMEPAGE = "http://hostap.epitest.fi/wpa_supplicant/"
-BUGTRACKER = "http://hostap.epitest.fi/bugz/"
-SECTION = "network"
-LICENSE = "GPLv2 | BSD"
-LIC_FILES_CHKSUM = "file://../COPYING;md5=ab87f20cd7e8c0d0a6539b34d3791d0e \
-                    file://../README;md5=5cb758942d25f6f61fd4ac388fd446fa \
-                    file://wpa_supplicant.c;beginline=1;endline=17;md5=8835156c8ab8cad6356ec7f39ebe3aba"
-DEPENDS = "gnutls dbus libnl"
-RRECOMMENDS_${PN} = "wpa-supplicant-passphrase wpa-supplicant-cli"
-
-SRC_URI = "\
-           file://defconfig-gnutls \
-           file://wpa-supplicant.sh \
-           file://wpa_supplicant.conf \
-           file://wpa_supplicant.conf-sane \
-           file://99_wpa_supplicant"
-
-S = "${WORKDIR}/wpa_supplicant-${PV}/wpa_supplicant"
-
-PACKAGES_prepend = "wpa-supplicant-passphrase wpa-supplicant-cli "
-FILES_wpa-supplicant-passphrase = "${bindir}/wpa_passphrase"
-FILES_wpa-supplicant-cli = "${sbindir}/wpa_cli"
-FILES_${PN} += "${datadir}/dbus-1/system-services/*"
-CONFFILES_${PN} += "${sysconfdir}/wpa_supplicant.conf"
-
-do_configure () {
-	install -m 0755 ${WORKDIR}/defconfig-gnutls .config
-}
-
-export EXTRA_CFLAGS = "${CFLAGS}"
-export BINDIR = "${sbindir}"
-
-do_compile () {
-	unset CFLAGS CPPFLAGS CXXFLAGS
-	oe_runmake
-}
-
-do_install () {
-	install -d ${D}${sbindir}
-	install -m 755 wpa_supplicant ${D}${sbindir}
-	install -m 755 wpa_cli        ${D}${sbindir}
-
-	install -d ${D}${bindir}
-	install -m 755 wpa_passphrase ${D}${bindir}
-
-	install -d ${D}${docdir}/wpa_supplicant
-	install -m 644 README ${WORKDIR}/wpa_supplicant.conf ${D}${docdir}/wpa_supplicant
-
-	install -d ${D}${sysconfdir}
-	install -m 600 ${WORKDIR}/wpa_supplicant.conf-sane ${D}${sysconfdir}/wpa_supplicant.conf
-
-	install -d ${D}${sysconfdir}/network/if-pre-up.d/
-	install -d ${D}${sysconfdir}/network/if-post-down.d/
-	install -d ${D}${sysconfdir}/network/if-down.d/
-	install -m 755 ${WORKDIR}/wpa-supplicant.sh ${D}${sysconfdir}/network/if-pre-up.d/wpa-supplicant
-	cd ${D}${sysconfdir}/network/ && \
-	ln -sf ../if-pre-up.d/wpa-supplicant if-post-down.d/wpa-supplicant
-
-	install -d ${D}/${sysconfdir}/dbus-1/system.d
-	install -m 644 ${S}/dbus/dbus-wpa_supplicant.conf ${D}/${sysconfdir}/dbus-1/system.d
-	install -d ${D}/${datadir}/dbus-1/system-services
-	install -m 644 ${S}/dbus/*.service ${D}/${datadir}/dbus-1/system-services
-
-	install -d ${D}/etc/default/volatiles
-	install -m 0644 ${WORKDIR}/99_wpa_supplicant ${D}/etc/default/volatiles
-}
-
-pkg_postinst_wpa-supplicant () {
-	# If we're offline, we don't need to do this.
-	if [ "x$D" != "x" ]; then
-		exit 0
-	fi
-
-	DBUSPID=`pidof dbus-daemon`
-
-	if [ "x$DBUSPID" != "x" ]; then
-		/etc/init.d/dbus-1 reload || true
-	fi
-}

meta-digi-del/recipes-connectivity/wpa-supplicant/wpa-supplicant/ccardxmx28js/defconfig

@@ -0,0 +1,524 @@
+# Example wpa_supplicant build time configuration
+#
+# This file lists the configuration options that are used when building the
+# hostapd binary. All lines starting with # are ignored. Configuration option
+# lines must be commented out complete, if they are not to be included, i.e.,
+# just setting VARIABLE=n is not disabling that variable.
+#
+# This file is included in Makefile, so variables like CFLAGS and LIBS can also
+# be modified from here. In most cases, these lines should use += in order not
+# to override previous values of the variables.
+
+
+# Uncomment following two lines and fix the paths if you have installed OpenSSL
+# or GnuTLS in non-default location
+#CFLAGS += -I/usr/local/openssl/include
+#LIBS += -L/usr/local/openssl/lib
+
+# Some Red Hat versions seem to include kerberos header files from OpenSSL, but
+# the kerberos files are not in the default include path. Following line can be
+# used to fix build issues on such systems (krb5.h not found).
+#CFLAGS += -I/usr/include/kerberos
+
+# Example configuration for various cross-compilation platforms
+
+#### sveasoft (e.g., for Linksys WRT54G) ######################################
+#CC=mipsel-uclibc-gcc
+#CC=/opt/brcm/hndtools-mipsel-uclibc/bin/mipsel-uclibc-gcc
+#CFLAGS += -Os
+#CPPFLAGS += -I../src/include -I../../src/router/openssl/include
+#LIBS += -L/opt/brcm/hndtools-mipsel-uclibc-0.9.19/lib -lssl
+###############################################################################
+
+#### openwrt (e.g., for Linksys WRT54G) #######################################
+#CC=mipsel-uclibc-gcc
+#CC=/opt/brcm/hndtools-mipsel-uclibc/bin/mipsel-uclibc-gcc
+#CFLAGS += -Os
+#CPPFLAGS=-I../src/include -I../openssl-0.9.7d/include \
+#	-I../WRT54GS/release/src/include
+#LIBS = -lssl
+###############################################################################
+
+
+# Driver interface for Host AP driver
+#CONFIG_DRIVER_HOSTAP=y
+
+# Driver interface for Agere driver
+#CONFIG_DRIVER_HERMES=y
+# Change include directories to match with the local setup
+#CFLAGS += -I../../hcf -I../../include -I../../include/hcf
+#CFLAGS += -I../../include/wireless
+
+# Driver interface for madwifi driver
+# Deprecated; use CONFIG_DRIVER_WEXT=y instead.
+#CONFIG_DRIVER_MADWIFI=y
+# Set include directory to the madwifi source tree
+#CFLAGS += -I../../madwifi
+
+# Driver interface for ndiswrapper
+# Deprecated; use CONFIG_DRIVER_WEXT=y instead.
+#CONFIG_DRIVER_NDISWRAPPER=y
+
+# Driver interface for Atmel driver
+#CONFIG_DRIVER_ATMEL=y
+
+# Driver interface for old Broadcom driver
+# Please note that the newer Broadcom driver ("hybrid Linux driver") supports
+# Linux wireless extensions and does not need (or even work) with the old
+# driver wrapper. Use CONFIG_DRIVER_WEXT=y with that driver.
+#CONFIG_DRIVER_BROADCOM=y
+# Example path for wlioctl.h; change to match your configuration
+#CFLAGS += -I/opt/WRT54GS/release/src/include
+
+# Driver interface for Intel ipw2100/2200 driver
+# Deprecated; use CONFIG_DRIVER_WEXT=y instead.
+#CONFIG_DRIVER_IPW=y
+
+# Driver interface for Ralink driver
+#CONFIG_DRIVER_RALINK=y
+
+# Driver interface for generic Linux wireless extensions
+# Note: WEXT is deprecated in the current Linux kernel version and no new
+# functionality is added to it. nl80211-based interface is the new
+# replacement for WEXT and its use allows wpa_supplicant to properly control
+# the driver to improve existing functionality like roaming and to support new
+# functionality.
+CONFIG_DRIVER_WEXT=y
+
+# Driver interface for Linux drivers using the nl80211 kernel interface
+CONFIG_LIBNL32=y
+CONFIG_DRIVER_NL80211=y
+
+# Driver interface for FreeBSD net80211 layer (e.g., Atheros driver)
+#CONFIG_DRIVER_BSD=y
+#CFLAGS += -I/usr/local/include
+#LIBS += -L/usr/local/lib
+#LIBS_p += -L/usr/local/lib
+#LIBS_c += -L/usr/local/lib
+
+# Driver interface for Windows NDIS
+#CONFIG_DRIVER_NDIS=y
+#CFLAGS += -I/usr/include/w32api/ddk
+#LIBS += -L/usr/local/lib
+# For native build using mingw
+#CONFIG_NATIVE_WINDOWS=y
+# Additional directories for cross-compilation on Linux host for mingw target
+#CFLAGS += -I/opt/mingw/mingw32/include/ddk
+#LIBS += -L/opt/mingw/mingw32/lib
+#CC=mingw32-gcc
+# By default, driver_ndis uses WinPcap for low-level operations. This can be
+# replaced with the following option which replaces WinPcap calls with NDISUIO.
+# However, this requires that WZC is disabled (net stop wzcsvc) before starting
+# wpa_supplicant.
+# CONFIG_USE_NDISUIO=y
+
+# Driver interface for development testing
+#CONFIG_DRIVER_TEST=y
+
+# Driver interface for wired Ethernet drivers
+CONFIG_DRIVER_WIRED=y
+
+# Driver interface for the Broadcom RoboSwitch family
+#CONFIG_DRIVER_ROBOSWITCH=y
+
+# Driver interface for no driver (e.g., WPS ER only)
+#CONFIG_DRIVER_NONE=y
+
+# Solaris libraries
+#LIBS += -lsocket -ldlpi -lnsl
+#LIBS_c += -lsocket
+
+# Enable IEEE 802.1X Supplicant (automatically included if any EAP method is
+# included)
+CONFIG_IEEE8021X_EAPOL=y
+
+# EAP-MD5
+CONFIG_EAP_MD5=y
+
+# EAP-MSCHAPv2
+CONFIG_EAP_MSCHAPV2=y
+
+# EAP-TLS
+CONFIG_EAP_TLS=y
+
+# EAL-PEAP
+CONFIG_EAP_PEAP=y
+
+# EAP-TTLS
+CONFIG_EAP_TTLS=y
+
+# EAP-FAST
+# Note: Default OpenSSL package does not include support for all the
+# functionality needed for EAP-FAST. If EAP-FAST is enabled with OpenSSL,
+# the OpenSSL library must be patched (openssl-0.9.8d-tls-extensions.patch)
+# to add the needed functions.
+CONFIG_EAP_FAST=y
+
+# EAP-GTC
+CONFIG_EAP_GTC=y
+
+# EAP-OTP
+CONFIG_EAP_OTP=y
+
+# EAP-SIM (enable CONFIG_PCSC, if EAP-SIM is used)
+CONFIG_EAP_SIM=y
+
+# EAP-PSK (experimental; this is _not_ needed for WPA-PSK)
+CONFIG_EAP_PSK=y
+
+# EAP-pwd (secure authentication using only a password)
+#CONFIG_EAP_PWD=y
+
+# EAP-PAX
+CONFIG_EAP_PAX=y
+
+# LEAP
+CONFIG_EAP_LEAP=y
+
+# EAP-AKA (enable CONFIG_PCSC, if EAP-AKA is used)
+CONFIG_EAP_AKA=y
+
+# EAP-AKA' (enable CONFIG_PCSC, if EAP-AKA' is used).
+# This requires CONFIG_EAP_AKA to be enabled, too.
+#CONFIG_EAP_AKA_PRIME=y
+
+# Enable USIM simulator (Milenage) for EAP-AKA
+#CONFIG_USIM_SIMULATOR=y
+
+# EAP-SAKE
+CONFIG_EAP_SAKE=y
+
+# EAP-GPSK
+CONFIG_EAP_GPSK=y
+# Include support for optional SHA256 cipher suite in EAP-GPSK
+#CONFIG_EAP_GPSK_SHA256=y
+
+# EAP-TNC and related Trusted Network Connect support (experimental)
+#CONFIG_EAP_TNC=y
+
+# Wi-Fi Protected Setup (WPS)
+CONFIG_WPS=y
+# Enable WSC 2.0 support
+CONFIG_WPS2=y
+# Enable WPS external registrar functionality
+#CONFIG_WPS_ER=y
+# Disable credentials for an open network by default when acting as a WPS
+# registrar.
+#CONFIG_WPS_REG_DISABLE_OPEN=y
+# Enable WPS support with NFC config method
+#CONFIG_WPS_NFC=y
+
+# EAP-IKEv2
+CONFIG_EAP_IKEV2=y
+
+# PKCS#12 (PFX) support (used to read private key and certificate file from
+# a file that usually has extension .p12 or .pfx)
+CONFIG_PKCS12=y
+
+# Smartcard support (i.e., private key on a smartcard), e.g., with openssl
+# engine.
+CONFIG_SMARTCARD=y
+
+# PC/SC interface for smartcards (USIM, GSM SIM)
+# Enable this if EAP-SIM or EAP-AKA is included
+#CONFIG_PCSC=y
+
+# Support HT overrides (disable HT/HT40, mask MCS rates, etc.)
+CONFIG_HT_OVERRIDES=y
+
+# Development testing
+#CONFIG_EAPOL_TEST=y
+
+# Select control interface backend for external programs, e.g, wpa_cli:
+# unix = UNIX domain sockets (default for Linux/*BSD)
+# udp = UDP sockets using localhost (127.0.0.1)
+# named_pipe = Windows Named Pipe (default for Windows)
+# udp-remote = UDP sockets with remote access (only for tests systems/purpose)
+# y = use default (backwards compatibility)
+# If this option is commented out, control interface is not included in the
+# build.
+CONFIG_CTRL_IFACE=unix
+
+# Include support for GNU Readline and History Libraries in wpa_cli.
+# When building a wpa_cli binary for distribution, please note that these
+# libraries are licensed under GPL and as such, BSD license may not apply for
+# the resulting binary.
+#CONFIG_READLINE=y
+
+# Include internal line edit mode in wpa_cli. This can be used as a replacement
+# for GNU Readline to provide limited command line editing and history support.
+CONFIG_WPA_CLI_EDIT=y
+
+# Remove debugging code that is printing out debug message to stdout.
+# This can be used to reduce the size of the wpa_supplicant considerably
+# if debugging code is not needed. The size reduction can be around 35%
+# (e.g., 90 kB).
+#CONFIG_NO_STDOUT_DEBUG=y
+
+# Remove WPA support, e.g., for wired-only IEEE 802.1X supplicant, to save
+# 35-50 kB in code size.
+#CONFIG_NO_WPA=y
+
+# Remove WPA2 support. This allows WPA to be used, but removes WPA2 code to
+# save about 1 kB in code size when building only WPA-Personal (no EAP support)
+# or 6 kB if building for WPA-Enterprise.
+#CONFIG_NO_WPA2=y
+
+# Remove IEEE 802.11i/WPA-Personal ASCII passphrase support
+# This option can be used to reduce code size by removing support for
+# converting ASCII passphrases into PSK. If this functionality is removed, the
+# PSK can only be configured as the 64-octet hexstring (e.g., from
+# wpa_passphrase). This saves about 0.5 kB in code size.
+#CONFIG_NO_WPA_PASSPHRASE=y
+
+# Disable scan result processing (ap_mode=1) to save code size by about 1 kB.
+# This can be used if ap_scan=1 mode is never enabled.
+#CONFIG_NO_SCAN_PROCESSING=y
+
+# Select configuration backend:
+# file = text file (e.g., wpa_supplicant.conf; note: the configuration file
+#	path is given on command line, not here; this option is just used to
+#	select the backend that allows configuration files to be used)
+# winreg = Windows registry (see win_example.reg for an example)
+CONFIG_BACKEND=file
+
+# Remove configuration write functionality (i.e., to allow the configuration
+# file to be updated based on runtime configuration changes). The runtime
+# configuration can still be changed, the changes are just not going to be
+# persistent over restarts. This option can be used to reduce code size by
+# about 3.5 kB.
+#CONFIG_NO_CONFIG_WRITE=y
+
+# Remove support for configuration blobs to reduce code size by about 1.5 kB.
+#CONFIG_NO_CONFIG_BLOBS=y
+
+# Select program entry point implementation:
+# main = UNIX/POSIX like main() function (default)
+# main_winsvc = Windows service (read parameters from registry)
+# main_none = Very basic example (development use only)
+#CONFIG_MAIN=main
+
+# Select wrapper for operatins system and C library specific functions
+# unix = UNIX/POSIX like systems (default)
+# win32 = Windows systems
+# none = Empty template
+#CONFIG_OS=unix
+
+# Select event loop implementation
+# eloop = select() loop (default)
+# eloop_win = Windows events and WaitForMultipleObject() loop
+# eloop_none = Empty template
+#CONFIG_ELOOP=eloop
+
+# Should we use poll instead of select? Select is used by default.
+#CONFIG_ELOOP_POLL=y
+
+# Select layer 2 packet implementation
+# linux = Linux packet socket (default)
+# pcap = libpcap/libdnet/WinPcap
+# freebsd = FreeBSD libpcap
+# winpcap = WinPcap with receive thread
+# ndis = Windows NDISUIO (note: requires CONFIG_USE_NDISUIO=y)
+# none = Empty template
+#CONFIG_L2_PACKET=linux
+
+# PeerKey handshake for Station to Station Link (IEEE 802.11e DLS)
+CONFIG_PEERKEY=y
+
+# IEEE 802.11w (management frame protection), also known as PMF
+# Driver support is also needed for IEEE 802.11w.
+#CONFIG_IEEE80211W=y
+
+# Select TLS implementation
+# openssl = OpenSSL (default)
+# gnutls = GnuTLS
+# internal = Internal TLSv1 implementation (experimental)
+# none = Empty template
+#CONFIG_TLS=openssl
+
+# TLS-based EAP methods require at least TLS v1.0. Newer version of TLS (v1.1)
+# can be enabled to get a stronger construction of messages when block ciphers
+# are used. It should be noted that some existing TLS v1.0 -based
+# implementation may not be compatible with TLS v1.1 message (ClientHello is
+# sent prior to negotiating which version will be used)
+#CONFIG_TLSV11=y
+
+# TLS-based EAP methods require at least TLS v1.0. Newer version of TLS (v1.2)
+# can be enabled to enable use of stronger crypto algorithms. It should be
+# noted that some existing TLS v1.0 -based implementation may not be compatible
+# with TLS v1.2 message (ClientHello is sent prior to negotiating which version
+# will be used)
+#CONFIG_TLSV12=y
+
+# If CONFIG_TLS=internal is used, additional library and include paths are
+# needed for LibTomMath. Alternatively, an integrated, minimal version of
+# LibTomMath can be used. See beginning of libtommath.c for details on benefits
+# and drawbacks of this option.
+#CONFIG_INTERNAL_LIBTOMMATH=y
+#ifndef CONFIG_INTERNAL_LIBTOMMATH
+#LTM_PATH=/usr/src/libtommath-0.39
+#CFLAGS += -I$(LTM_PATH)
+#LIBS += -L$(LTM_PATH)
+#LIBS_p += -L$(LTM_PATH)
+#endif
+# At the cost of about 4 kB of additional binary size, the internal LibTomMath
+# can be configured to include faster routines for exptmod, sqr, and div to
+# speed up DH and RSA calculation considerably
+#CONFIG_INTERNAL_LIBTOMMATH_FAST=y
+
+# Include NDIS event processing through WMI into wpa_supplicant/wpasvc.
+# This is only for Windows builds and requires WMI-related header files and
+# WbemUuid.Lib from Platform SDK even when building with MinGW.
+#CONFIG_NDIS_EVENTS_INTEGRATED=y
+#PLATFORMSDKLIB="/opt/Program Files/Microsoft Platform SDK/Lib"
+
+# Add support for old DBus control interface
+# (fi.epitest.hostap.WPASupplicant)
+#CONFIG_CTRL_IFACE_DBUS=y
+
+# Add support for new DBus control interface
+# (fi.w1.hostap.wpa_supplicant1)
+#CONFIG_CTRL_IFACE_DBUS_NEW=y
+
+# Add introspection support for new DBus control interface
+#CONFIG_CTRL_IFACE_DBUS_INTRO=y
+
+# Add support for loading EAP methods dynamically as shared libraries.
+# When this option is enabled, each EAP method can be either included
+# statically (CONFIG_EAP_<method>=y) or dynamically (CONFIG_EAP_<method>=dyn).
+# Dynamic EAP methods are build as shared objects (eap_*.so) and they need to
+# be loaded in the beginning of the wpa_supplicant configuration file
+# (see load_dynamic_eap parameter in the example file) before being used in
+# the network blocks.
+#
+# Note that some shared parts of EAP methods are included in the main program
+# and in order to be able to use dynamic EAP methods using these parts, the
+# main program must have been build with the EAP method enabled (=y or =dyn).
+# This means that EAP-TLS/PEAP/TTLS/FAST cannot be added as dynamic libraries
+# unless at least one of them was included in the main build to force inclusion
+# of the shared code. Similarly, at least one of EAP-SIM/AKA must be included
+# in the main build to be able to load these methods dynamically.
+#
+# Please also note that using dynamic libraries will increase the total binary
+# size. Thus, it may not be the best option for targets that have limited
+# amount of memory/flash.
+#CONFIG_DYNAMIC_EAP_METHODS=y
+
+# IEEE Std 802.11r-2008 (Fast BSS Transition)
+#CONFIG_IEEE80211R=y
+
+# Add support for writing debug log to a file (/tmp/wpa_supplicant-log-#.txt)
+#CONFIG_DEBUG_FILE=y
+
+# Send debug messages to syslog instead of stdout
+#CONFIG_DEBUG_SYSLOG=y
+# Set syslog facility for debug messages
+#CONFIG_DEBUG_SYSLOG_FACILITY=LOG_DAEMON
+
+# Add support for sending all debug messages (regardless of debug verbosity)
+# to the Linux kernel tracing facility. This helps debug the entire stack by
+# making it easy to record everything happening from the driver up into the
+# same file, e.g., using trace-cmd.
+#CONFIG_DEBUG_LINUX_TRACING=y
+
+# Enable privilege separation (see README 'Privilege separation' for details)
+#CONFIG_PRIVSEP=y
+
+# Enable mitigation against certain attacks against TKIP by delaying Michael
+# MIC error reports by a random amount of time between 0 and 60 seconds
+#CONFIG_DELAYED_MIC_ERROR_REPORT=y
+
+# Enable tracing code for developer debugging
+# This tracks use of memory allocations and other registrations and reports
+# incorrect use with a backtrace of call (or allocation) location.
+#CONFIG_WPA_TRACE=y
+# For BSD, uncomment these.
+#LIBS += -lexecinfo
+#LIBS_p += -lexecinfo
+#LIBS_c += -lexecinfo
+
+# Use libbfd to get more details for developer debugging
+# This enables use of libbfd to get more detailed symbols for the backtraces
+# generated by CONFIG_WPA_TRACE=y.
+#CONFIG_WPA_TRACE_BFD=y
+# For BSD, uncomment these.
+#LIBS += -lbfd -liberty -lz
+#LIBS_p += -lbfd -liberty -lz
+#LIBS_c += -lbfd -liberty -lz
+
+# wpa_supplicant depends on strong random number generation being available
+# from the operating system. os_get_random() function is used to fetch random
+# data when needed, e.g., for key generation. On Linux and BSD systems, this
+# works by reading /dev/urandom. It should be noted that the OS entropy pool
+# needs to be properly initialized before wpa_supplicant is started. This is
+# important especially on embedded devices that do not have a hardware random
+# number generator and may by default start up with minimal entropy available
+# for random number generation.
+#
+# As a safety net, wpa_supplicant is by default trying to internally collect
+# additional entropy for generating random data to mix in with the data fetched
+# from the OS. This by itself is not considered to be very strong, but it may
+# help in cases where the system pool is not initialized properly. However, it
+# is very strongly recommended that the system pool is initialized with enough
+# entropy either by using hardware assisted random number generator or by
+# storing state over device reboots.
+#
+# wpa_supplicant can be configured to maintain its own entropy store over
+# restarts to enhance random number generation. This is not perfect, but it is
+# much more secure than using the same sequence of random numbers after every
+# reboot. This can be enabled with -e<entropy file> command line option. The
+# specified file needs to be readable and writable by wpa_supplicant.
+#
+# If the os_get_random() is known to provide strong random data (e.g., on
+# Linux/BSD, the board in question is known to have reliable source of random
+# data from /dev/urandom), the internal wpa_supplicant random pool can be
+# disabled. This will save some in binary size and CPU use. However, this
+# should only be considered for builds that are known to be used on devices
+# that meet the requirements described above.
+CONFIG_NO_RANDOM_POOL=y
+
+# IEEE 802.11n (High Throughput) support (mainly for AP mode)
+CONFIG_IEEE80211N=y
+
+# Wireless Network Management (IEEE Std 802.11v-2011)
+# Note: This is experimental and not complete implementation.
+#CONFIG_WNM=y
+
+# Interworking (IEEE 802.11u)
+# This can be used to enable functionality to improve interworking with
+# external networks (GAS/ANQP to learn more about the networks and network
+# selection based on available credentials).
+#CONFIG_INTERWORKING=y
+
+# Hotspot 2.0
+#CONFIG_HS20=y
+
+# AP mode operations with wpa_supplicant
+# This can be used for controlling AP mode operations with wpa_supplicant. It
+# should be noted that this is mainly aimed at simple cases like
+# WPA2-Personal while more complex configurations like WPA2-Enterprise with an
+# external RADIUS server can be supported with hostapd.
+CONFIG_AP=y
+
+# P2P (Wi-Fi Direct)
+# This can be used to enable P2P support in wpa_supplicant. See README-P2P for
+# more information on P2P operations.
+CONFIG_P2P=y
+
+# Autoscan
+# This can be used to enable automatic scan support in wpa_supplicant.
+# See wpa_supplicant.conf for more information on autoscan usage.
+#
+# Enabling directly a module will enable autoscan support.
+# For exponential module:
+#CONFIG_AUTOSCAN_EXPONENTIAL=y
+# For periodic module:
+#CONFIG_AUTOSCAN_PERIODIC=y
+
+# Password (and passphrase, etc.) backend for external storage
+# These optional mechanisms can be used to add support for storing passwords
+# and other secrets in external (to wpa_supplicant) location. This allows, for
+# example, operating system specific key storage to be used
+#
+# External password backend for testing purposes (developer use)
+#CONFIG_EXT_PASSWORD_TEST=y

meta-digi-del/recipes-connectivity/wpa-supplicant/wpa-supplicant/ccxmx51js/defconfig

@@ -41,7 +41,7 @@
 
 
 # Driver interface for Host AP driver
-CONFIG_DRIVER_HOSTAP=y
+#CONFIG_DRIVER_HOSTAP=y
 
 # Driver interface for Agere driver
 #CONFIG_DRIVER_HERMES=y
@@ -60,7 +60,7 @@ CONFIG_DRIVER_HOSTAP=y
 #CONFIG_DRIVER_NDISWRAPPER=y
 
 # Driver interface for Atmel driver
-# CONFIG_DRIVER_ATMEL=y
+#CONFIG_DRIVER_ATMEL=y
 
 # Driver interface for old Broadcom driver
 # Please note that the newer Broadcom driver ("hybrid Linux driver") supports
@@ -78,11 +78,15 @@ CONFIG_DRIVER_HOSTAP=y
 #CONFIG_DRIVER_RALINK=y
 
 # Driver interface for generic Linux wireless extensions
+# Note: WEXT is deprecated in the current Linux kernel version and no new
+# functionality is added to it. nl80211-based interface is the new
+# replacement for WEXT and its use allows wpa_supplicant to properly control
+# the driver to improve existing functionality like roaming and to support new
+# functionality.
 CONFIG_DRIVER_WEXT=y
 
 # Driver interface for Linux drivers using the nl80211 kernel interface
-CONFIG_LIBNL20=y
+#CONFIG_DRIVER_NL80211=y
-CONFIG_DRIVER_NL80211=y
 
 # Driver interface for FreeBSD net80211 layer (e.g., Atheros driver)
 #CONFIG_DRIVER_BSD=y
@@ -110,13 +114,8 @@ CONFIG_DRIVER_NL80211=y
 # Driver interface for development testing
 #CONFIG_DRIVER_TEST=y
 
-# Include client MLME (management frame processing) for test driver
-# This can be used to test MLME operations in hostapd with the test interface.
-# space.
-#CONFIG_CLIENT_MLME=y
-
 # Driver interface for wired Ethernet drivers
-CONFIG_DRIVER_WIRED=y
+#CONFIG_DRIVER_WIRED=y
 
 # Driver interface for the Broadcom RoboSwitch family
 #CONFIG_DRIVER_ROBOSWITCH=y
@@ -124,6 +123,10 @@ CONFIG_DRIVER_WIRED=y
 # Driver interface for no driver (e.g., WPS ER only)
 #CONFIG_DRIVER_NONE=y
 
+# Solaris libraries
+#LIBS += -lsocket -ldlpi -lnsl
+#LIBS_c += -lsocket
+
 # Enable IEEE 802.1X Supplicant (automatically included if any EAP method is
 # included)
 CONFIG_IEEE8021X_EAPOL=y
@@ -162,6 +165,9 @@ CONFIG_EAP_OTP=y
 # EAP-PSK (experimental; this is _not_ needed for WPA-PSK)
 #CONFIG_EAP_PSK=y
 
+# EAP-pwd (secure authentication using only a password)
+#CONFIG_EAP_PWD=y
+
 # EAP-PAX
 #CONFIG_EAP_PAX=y
 
@@ -190,7 +196,16 @@ CONFIG_EAP_LEAP=y
 #CONFIG_EAP_TNC=y
 
 # Wi-Fi Protected Setup (WPS)
-#CONFIG_WPS=y
+CONFIG_WPS=y
+# Enable WSC 2.0 support
+CONFIG_WPS2=y
+# Enable WPS external registrar functionality
+#CONFIG_WPS_ER=y
+# Disable credentials for an open network by default when acting as a WPS
+# registrar.
+#CONFIG_WPS_REG_DISABLE_OPEN=y
+# Enable WPS support with NFC config method
+#CONFIG_WPS_NFC=y
 
 # EAP-IKEv2
 #CONFIG_EAP_IKEV2=y
@@ -207,6 +222,9 @@ CONFIG_SMARTCARD=y
 # Enable this if EAP-SIM or EAP-AKA is included
 #CONFIG_PCSC=y
 
+# Support HT overrides (disable HT/HT40, mask MCS rates, etc.)
+#CONFIG_HT_OVERRIDES=y
+
 # Development testing
 #CONFIG_EAPOL_TEST=y
 
@@ -214,6 +232,7 @@ CONFIG_SMARTCARD=y
 # unix = UNIX domain sockets (default for Linux/*BSD)
 # udp = UDP sockets using localhost (127.0.0.1)
 # named_pipe = Windows Named Pipe (default for Windows)
+# udp-remote = UDP sockets with remote access (only for tests systems/purpose)
 # y = use default (backwards compatibility)
 # If this option is commented out, control interface is not included in the
 # build.
@@ -225,11 +244,15 @@ CONFIG_CTRL_IFACE=y
 # the resulting binary.
 #CONFIG_READLINE=y
 
+# Include internal line edit mode in wpa_cli. This can be used as a replacement
+# for GNU Readline to provide limited command line editing and history support.
+CONFIG_WPA_CLI_EDIT=y
+
 # Remove debugging code that is printing out debug message to stdout.
 # This can be used to reduce the size of the wpa_supplicant considerably
 # if debugging code is not needed. The size reduction can be around 35%
 # (e.g., 90 kB).
-#CONFIG_NO_STDOUT_DEBUG=y
+CONFIG_NO_STDOUT_DEBUG=y
 
 # Remove WPA support, e.g., for wired-only IEEE 802.1X supplicant, to save
 # 35-50 kB in code size.
@@ -286,6 +309,9 @@ CONFIG_BACKEND=file
 # eloop_none = Empty template
 #CONFIG_ELOOP=eloop
 
+# Should we use poll instead of select? Select is used by default.
+#CONFIG_ELOOP_POLL=y
+
 # Select layer 2 packet implementation
 # linux = Linux packet socket (default)
 # pcap = libpcap/libdnet/WinPcap
@@ -298,26 +324,30 @@ CONFIG_BACKEND=file
 # PeerKey handshake for Station to Station Link (IEEE 802.11e DLS)
 CONFIG_PEERKEY=y
 
-# IEEE 802.11w (management frame protection)
+# IEEE 802.11w (management frame protection), also known as PMF
-# This version is an experimental implementation based on IEEE 802.11w/D1.0
-# draft and is subject to change since the standard has not yet been finalized.
 # Driver support is also needed for IEEE 802.11w.
 #CONFIG_IEEE80211W=y
 
 # Select TLS implementation
 # openssl = OpenSSL (default)
-# gnutls = GnuTLS (needed for TLS/IA, see also CONFIG_GNUTLS_EXTRA)
+# gnutls = GnuTLS
 # internal = Internal TLSv1 implementation (experimental)
 # none = Empty template
 #CONFIG_TLS=openssl
 
-# Whether to enable TLS/IA support, which is required for EAP-TTLSv1.
+# TLS-based EAP methods require at least TLS v1.0. Newer version of TLS (v1.1)
-# You need CONFIG_TLS=gnutls for this to have any effect. Please note that
+# can be enabled to get a stronger construction of messages when block ciphers
-# even though the core GnuTLS library is released under LGPL, this extra
+# are used. It should be noted that some existing TLS v1.0 -based
-# library uses GPL and as such, the terms of GPL apply to the combination
+# implementation may not be compatible with TLS v1.1 message (ClientHello is
-# of wpa_supplicant and GnuTLS if this option is enabled. BSD license may not
+# sent prior to negotiating which version will be used)
-# apply for distribution of the resulting binary.
+#CONFIG_TLSV11=y
-#CONFIG_GNUTLS_EXTRA=y
+
+# TLS-based EAP methods require at least TLS v1.0. Newer version of TLS (v1.2)
+# can be enabled to enable use of stronger crypto algorithms. It should be
+# noted that some existing TLS v1.0 -based implementation may not be compatible
+# with TLS v1.2 message (ClientHello is sent prior to negotiating which version
+# will be used)
+#CONFIG_TLSV12=y
 
 # If CONFIG_TLS=internal is used, additional library and include paths are
 # needed for LibTomMath. Alternatively, an integrated, minimal version of
@@ -379,6 +409,17 @@ CONFIG_PEERKEY=y
 # Add support for writing debug log to a file (/tmp/wpa_supplicant-log-#.txt)
 #CONFIG_DEBUG_FILE=y
 
+# Send debug messages to syslog instead of stdout
+#CONFIG_DEBUG_SYSLOG=y
+# Set syslog facility for debug messages
+#CONFIG_DEBUG_SYSLOG_FACILITY=LOG_DAEMON
+
+# Add support for sending all debug messages (regardless of debug verbosity)
+# to the Linux kernel tracing facility. This helps debug the entire stack by
+# making it easy to record everything happening from the driver up into the
+# same file, e.g., using trace-cmd.
+#CONFIG_DEBUG_LINUX_TRACING=y
+
 # Enable privilege separation (see README 'Privilege separation' for details)
 #CONFIG_PRIVSEP=y
 
@@ -390,7 +431,7 @@ CONFIG_PEERKEY=y
 # This tracks use of memory allocations and other registrations and reports
 # incorrect use with a backtrace of call (or allocation) location.
 #CONFIG_WPA_TRACE=y
-# For BSD, comment out these.
+# For BSD, uncomment these.
 #LIBS += -lexecinfo
 #LIBS_p += -lexecinfo
 #LIBS_c += -lexecinfo
@@ -399,11 +440,84 @@ CONFIG_PEERKEY=y
 # This enables use of libbfd to get more detailed symbols for the backtraces
 # generated by CONFIG_WPA_TRACE=y.
 #CONFIG_WPA_TRACE_BFD=y
-# For BSD, comment out these.
+# For BSD, uncomment these.
 #LIBS += -lbfd -liberty -lz
 #LIBS_p += -lbfd -liberty -lz
 #LIBS_c += -lbfd -liberty -lz
-CONFIG_TLS = gnutls
+
-#CONFIG_GNUTLS_EXTRA=y
+# wpa_supplicant depends on strong random number generation being available
-CONFIG_CTRL_IFACE_DBUS=y
+# from the operating system. os_get_random() function is used to fetch random
-CONFIG_CTRL_IFACE_DBUS_NEW=y
+# data when needed, e.g., for key generation. On Linux and BSD systems, this
+# works by reading /dev/urandom. It should be noted that the OS entropy pool
+# needs to be properly initialized before wpa_supplicant is started. This is
+# important especially on embedded devices that do not have a hardware random
+# number generator and may by default start up with minimal entropy available
+# for random number generation.
+#
+# As a safety net, wpa_supplicant is by default trying to internally collect
+# additional entropy for generating random data to mix in with the data fetched
+# from the OS. This by itself is not considered to be very strong, but it may
+# help in cases where the system pool is not initialized properly. However, it
+# is very strongly recommended that the system pool is initialized with enough
+# entropy either by using hardware assisted random number generator or by
+# storing state over device reboots.
+#
+# wpa_supplicant can be configured to maintain its own entropy store over
+# restarts to enhance random number generation. This is not perfect, but it is
+# much more secure than using the same sequence of random numbers after every
+# reboot. This can be enabled with -e<entropy file> command line option. The
+# specified file needs to be readable and writable by wpa_supplicant.
+#
+# If the os_get_random() is known to provide strong random data (e.g., on
+# Linux/BSD, the board in question is known to have reliable source of random
+# data from /dev/urandom), the internal wpa_supplicant random pool can be
+# disabled. This will save some in binary size and CPU use. However, this
+# should only be considered for builds that are known to be used on devices
+# that meet the requirements described above.
+#CONFIG_NO_RANDOM_POOL=y
+
+# IEEE 802.11n (High Throughput) support (mainly for AP mode)
+#CONFIG_IEEE80211N=y
+
+# Wireless Network Management (IEEE Std 802.11v-2011)
+# Note: This is experimental and not complete implementation.
+#CONFIG_WNM=y
+
+# Interworking (IEEE 802.11u)
+# This can be used to enable functionality to improve interworking with
+# external networks (GAS/ANQP to learn more about the networks and network
+# selection based on available credentials).
+#CONFIG_INTERWORKING=y
+
+# Hotspot 2.0
+#CONFIG_HS20=y
+
+# AP mode operations with wpa_supplicant
+# This can be used for controlling AP mode operations with wpa_supplicant. It
+# should be noted that this is mainly aimed at simple cases like
+# WPA2-Personal while more complex configurations like WPA2-Enterprise with an
+# external RADIUS server can be supported with hostapd.
+#CONFIG_AP=y
+
+# P2P (Wi-Fi Direct)
+# This can be used to enable P2P support in wpa_supplicant. See README-P2P for
+# more information on P2P operations.
+#CONFIG_P2P=y
+
+# Autoscan
+# This can be used to enable automatic scan support in wpa_supplicant.
+# See wpa_supplicant.conf for more information on autoscan usage.
+#
+# Enabling directly a module will enable autoscan support.
+# For exponential module:
+#CONFIG_AUTOSCAN_EXPONENTIAL=y
+# For periodic module:
+#CONFIG_AUTOSCAN_PERIODIC=y
+
+# Password (and passphrase, etc.) backend for external storage
+# These optional mechanisms can be used to add support for storing passwords
+# and other secrets in external (to wpa_supplicant) location. This allows, for
+# example, operating system specific key storage to be used
+#
+# External password backend for testing purposes (developer use)
+#CONFIG_EXT_PASSWORD_TEST=y

meta-digi-del/recipes-connectivity/wpa-supplicant/wpa-supplicant/ccxmx53js/defconfig

@@ -0,0 +1,523 @@
+# Example wpa_supplicant build time configuration
+#
+# This file lists the configuration options that are used when building the
+# hostapd binary. All lines starting with # are ignored. Configuration option
+# lines must be commented out complete, if they are not to be included, i.e.,
+# just setting VARIABLE=n is not disabling that variable.
+#
+# This file is included in Makefile, so variables like CFLAGS and LIBS can also
+# be modified from here. In most cases, these lines should use += in order not
+# to override previous values of the variables.
+
+
+# Uncomment following two lines and fix the paths if you have installed OpenSSL
+# or GnuTLS in non-default location
+#CFLAGS += -I/usr/local/openssl/include
+#LIBS += -L/usr/local/openssl/lib
+
+# Some Red Hat versions seem to include kerberos header files from OpenSSL, but
+# the kerberos files are not in the default include path. Following line can be
+# used to fix build issues on such systems (krb5.h not found).
+#CFLAGS += -I/usr/include/kerberos
+
+# Example configuration for various cross-compilation platforms
+
+#### sveasoft (e.g., for Linksys WRT54G) ######################################
+#CC=mipsel-uclibc-gcc
+#CC=/opt/brcm/hndtools-mipsel-uclibc/bin/mipsel-uclibc-gcc
+#CFLAGS += -Os
+#CPPFLAGS += -I../src/include -I../../src/router/openssl/include
+#LIBS += -L/opt/brcm/hndtools-mipsel-uclibc-0.9.19/lib -lssl
+###############################################################################
+
+#### openwrt (e.g., for Linksys WRT54G) #######################################
+#CC=mipsel-uclibc-gcc
+#CC=/opt/brcm/hndtools-mipsel-uclibc/bin/mipsel-uclibc-gcc
+#CFLAGS += -Os
+#CPPFLAGS=-I../src/include -I../openssl-0.9.7d/include \
+#	-I../WRT54GS/release/src/include
+#LIBS = -lssl
+###############################################################################
+
+
+# Driver interface for Host AP driver
+#CONFIG_DRIVER_HOSTAP=y
+
+# Driver interface for Agere driver
+#CONFIG_DRIVER_HERMES=y
+# Change include directories to match with the local setup
+#CFLAGS += -I../../hcf -I../../include -I../../include/hcf
+#CFLAGS += -I../../include/wireless
+
+# Driver interface for madwifi driver
+# Deprecated; use CONFIG_DRIVER_WEXT=y instead.
+#CONFIG_DRIVER_MADWIFI=y
+# Set include directory to the madwifi source tree
+#CFLAGS += -I../../madwifi
+
+# Driver interface for ndiswrapper
+# Deprecated; use CONFIG_DRIVER_WEXT=y instead.
+#CONFIG_DRIVER_NDISWRAPPER=y
+
+# Driver interface for Atmel driver
+#CONFIG_DRIVER_ATMEL=y
+
+# Driver interface for old Broadcom driver
+# Please note that the newer Broadcom driver ("hybrid Linux driver") supports
+# Linux wireless extensions and does not need (or even work) with the old
+# driver wrapper. Use CONFIG_DRIVER_WEXT=y with that driver.
+#CONFIG_DRIVER_BROADCOM=y
+# Example path for wlioctl.h; change to match your configuration
+#CFLAGS += -I/opt/WRT54GS/release/src/include
+
+# Driver interface for Intel ipw2100/2200 driver
+# Deprecated; use CONFIG_DRIVER_WEXT=y instead.
+#CONFIG_DRIVER_IPW=y
+
+# Driver interface for Ralink driver
+#CONFIG_DRIVER_RALINK=y
+
+# Driver interface for generic Linux wireless extensions
+# Note: WEXT is deprecated in the current Linux kernel version and no new
+# functionality is added to it. nl80211-based interface is the new
+# replacement for WEXT and its use allows wpa_supplicant to properly control
+# the driver to improve existing functionality like roaming and to support new
+# functionality.
+CONFIG_DRIVER_WEXT=y
+
+# Driver interface for Linux drivers using the nl80211 kernel interface
+#CONFIG_DRIVER_NL80211=y
+
+# Driver interface for FreeBSD net80211 layer (e.g., Atheros driver)
+#CONFIG_DRIVER_BSD=y
+#CFLAGS += -I/usr/local/include
+#LIBS += -L/usr/local/lib
+#LIBS_p += -L/usr/local/lib
+#LIBS_c += -L/usr/local/lib
+
+# Driver interface for Windows NDIS
+#CONFIG_DRIVER_NDIS=y
+#CFLAGS += -I/usr/include/w32api/ddk
+#LIBS += -L/usr/local/lib
+# For native build using mingw
+#CONFIG_NATIVE_WINDOWS=y
+# Additional directories for cross-compilation on Linux host for mingw target
+#CFLAGS += -I/opt/mingw/mingw32/include/ddk
+#LIBS += -L/opt/mingw/mingw32/lib
+#CC=mingw32-gcc
+# By default, driver_ndis uses WinPcap for low-level operations. This can be
+# replaced with the following option which replaces WinPcap calls with NDISUIO.
+# However, this requires that WZC is disabled (net stop wzcsvc) before starting
+# wpa_supplicant.
+# CONFIG_USE_NDISUIO=y
+
+# Driver interface for development testing
+#CONFIG_DRIVER_TEST=y
+
+# Driver interface for wired Ethernet drivers
+#CONFIG_DRIVER_WIRED=y
+
+# Driver interface for the Broadcom RoboSwitch family
+#CONFIG_DRIVER_ROBOSWITCH=y
+
+# Driver interface for no driver (e.g., WPS ER only)
+#CONFIG_DRIVER_NONE=y
+
+# Solaris libraries
+#LIBS += -lsocket -ldlpi -lnsl
+#LIBS_c += -lsocket
+
+# Enable IEEE 802.1X Supplicant (automatically included if any EAP method is
+# included)
+CONFIG_IEEE8021X_EAPOL=y
+
+# EAP-MD5
+CONFIG_EAP_MD5=y
+
+# EAP-MSCHAPv2
+CONFIG_EAP_MSCHAPV2=y
+
+# EAP-TLS
+CONFIG_EAP_TLS=y
+
+# EAL-PEAP
+CONFIG_EAP_PEAP=y
+
+# EAP-TTLS
+CONFIG_EAP_TTLS=y
+
+# EAP-FAST
+# Note: Default OpenSSL package does not include support for all the
+# functionality needed for EAP-FAST. If EAP-FAST is enabled with OpenSSL,
+# the OpenSSL library must be patched (openssl-0.9.8d-tls-extensions.patch)
+# to add the needed functions.
+#CONFIG_EAP_FAST=y
+
+# EAP-GTC
+CONFIG_EAP_GTC=y
+
+# EAP-OTP
+CONFIG_EAP_OTP=y
+
+# EAP-SIM (enable CONFIG_PCSC, if EAP-SIM is used)
+#CONFIG_EAP_SIM=y
+
+# EAP-PSK (experimental; this is _not_ needed for WPA-PSK)
+#CONFIG_EAP_PSK=y
+
+# EAP-pwd (secure authentication using only a password)
+#CONFIG_EAP_PWD=y
+
+# EAP-PAX
+#CONFIG_EAP_PAX=y
+
+# LEAP
+CONFIG_EAP_LEAP=y
+
+# EAP-AKA (enable CONFIG_PCSC, if EAP-AKA is used)
+#CONFIG_EAP_AKA=y
+
+# EAP-AKA' (enable CONFIG_PCSC, if EAP-AKA' is used).
+# This requires CONFIG_EAP_AKA to be enabled, too.
+#CONFIG_EAP_AKA_PRIME=y
+
+# Enable USIM simulator (Milenage) for EAP-AKA
+#CONFIG_USIM_SIMULATOR=y
+
+# EAP-SAKE
+#CONFIG_EAP_SAKE=y
+
+# EAP-GPSK
+#CONFIG_EAP_GPSK=y
+# Include support for optional SHA256 cipher suite in EAP-GPSK
+#CONFIG_EAP_GPSK_SHA256=y
+
+# EAP-TNC and related Trusted Network Connect support (experimental)
+#CONFIG_EAP_TNC=y
+
+# Wi-Fi Protected Setup (WPS)
+CONFIG_WPS=y
+# Enable WSC 2.0 support
+CONFIG_WPS2=y
+# Enable WPS external registrar functionality
+#CONFIG_WPS_ER=y
+# Disable credentials for an open network by default when acting as a WPS
+# registrar.
+#CONFIG_WPS_REG_DISABLE_OPEN=y
+# Enable WPS support with NFC config method
+#CONFIG_WPS_NFC=y
+
+# EAP-IKEv2
+#CONFIG_EAP_IKEV2=y
+
+# PKCS#12 (PFX) support (used to read private key and certificate file from
+# a file that usually has extension .p12 or .pfx)
+CONFIG_PKCS12=y
+
+# Smartcard support (i.e., private key on a smartcard), e.g., with openssl
+# engine.
+CONFIG_SMARTCARD=y
+
+# PC/SC interface for smartcards (USIM, GSM SIM)
+# Enable this if EAP-SIM or EAP-AKA is included
+#CONFIG_PCSC=y
+
+# Support HT overrides (disable HT/HT40, mask MCS rates, etc.)
+#CONFIG_HT_OVERRIDES=y
+
+# Development testing
+#CONFIG_EAPOL_TEST=y
+
+# Select control interface backend for external programs, e.g, wpa_cli:
+# unix = UNIX domain sockets (default for Linux/*BSD)
+# udp = UDP sockets using localhost (127.0.0.1)
+# named_pipe = Windows Named Pipe (default for Windows)
+# udp-remote = UDP sockets with remote access (only for tests systems/purpose)
+# y = use default (backwards compatibility)
+# If this option is commented out, control interface is not included in the
+# build.
+CONFIG_CTRL_IFACE=y
+
+# Include support for GNU Readline and History Libraries in wpa_cli.
+# When building a wpa_cli binary for distribution, please note that these
+# libraries are licensed under GPL and as such, BSD license may not apply for
+# the resulting binary.
+#CONFIG_READLINE=y
+
+# Include internal line edit mode in wpa_cli. This can be used as a replacement
+# for GNU Readline to provide limited command line editing and history support.
+CONFIG_WPA_CLI_EDIT=y
+
+# Remove debugging code that is printing out debug message to stdout.
+# This can be used to reduce the size of the wpa_supplicant considerably
+# if debugging code is not needed. The size reduction can be around 35%
+# (e.g., 90 kB).
+CONFIG_NO_STDOUT_DEBUG=y
+
+# Remove WPA support, e.g., for wired-only IEEE 802.1X supplicant, to save
+# 35-50 kB in code size.
+#CONFIG_NO_WPA=y
+
+# Remove WPA2 support. This allows WPA to be used, but removes WPA2 code to
+# save about 1 kB in code size when building only WPA-Personal (no EAP support)
+# or 6 kB if building for WPA-Enterprise.
+#CONFIG_NO_WPA2=y
+
+# Remove IEEE 802.11i/WPA-Personal ASCII passphrase support
+# This option can be used to reduce code size by removing support for
+# converting ASCII passphrases into PSK. If this functionality is removed, the
+# PSK can only be configured as the 64-octet hexstring (e.g., from
+# wpa_passphrase). This saves about 0.5 kB in code size.
+#CONFIG_NO_WPA_PASSPHRASE=y
+
+# Disable scan result processing (ap_mode=1) to save code size by about 1 kB.
+# This can be used if ap_scan=1 mode is never enabled.
+#CONFIG_NO_SCAN_PROCESSING=y
+
+# Select configuration backend:
+# file = text file (e.g., wpa_supplicant.conf; note: the configuration file
+#	path is given on command line, not here; this option is just used to
+#	select the backend that allows configuration files to be used)
+# winreg = Windows registry (see win_example.reg for an example)
+CONFIG_BACKEND=file
+
+# Remove configuration write functionality (i.e., to allow the configuration
+# file to be updated based on runtime configuration changes). The runtime
+# configuration can still be changed, the changes are just not going to be
+# persistent over restarts. This option can be used to reduce code size by
+# about 3.5 kB.
+#CONFIG_NO_CONFIG_WRITE=y
+
+# Remove support for configuration blobs to reduce code size by about 1.5 kB.
+#CONFIG_NO_CONFIG_BLOBS=y
+
+# Select program entry point implementation:
+# main = UNIX/POSIX like main() function (default)
+# main_winsvc = Windows service (read parameters from registry)
+# main_none = Very basic example (development use only)
+#CONFIG_MAIN=main
+
+# Select wrapper for operatins system and C library specific functions
+# unix = UNIX/POSIX like systems (default)
+# win32 = Windows systems
+# none = Empty template
+#CONFIG_OS=unix
+
+# Select event loop implementation
+# eloop = select() loop (default)
+# eloop_win = Windows events and WaitForMultipleObject() loop
+# eloop_none = Empty template
+#CONFIG_ELOOP=eloop
+
+# Should we use poll instead of select? Select is used by default.
+#CONFIG_ELOOP_POLL=y
+
+# Select layer 2 packet implementation
+# linux = Linux packet socket (default)
+# pcap = libpcap/libdnet/WinPcap
+# freebsd = FreeBSD libpcap
+# winpcap = WinPcap with receive thread
+# ndis = Windows NDISUIO (note: requires CONFIG_USE_NDISUIO=y)
+# none = Empty template
+#CONFIG_L2_PACKET=linux
+
+# PeerKey handshake for Station to Station Link (IEEE 802.11e DLS)
+CONFIG_PEERKEY=y
+
+# IEEE 802.11w (management frame protection), also known as PMF
+# Driver support is also needed for IEEE 802.11w.
+#CONFIG_IEEE80211W=y
+
+# Select TLS implementation
+# openssl = OpenSSL (default)
+# gnutls = GnuTLS
+# internal = Internal TLSv1 implementation (experimental)
+# none = Empty template
+#CONFIG_TLS=openssl
+
+# TLS-based EAP methods require at least TLS v1.0. Newer version of TLS (v1.1)
+# can be enabled to get a stronger construction of messages when block ciphers
+# are used. It should be noted that some existing TLS v1.0 -based
+# implementation may not be compatible with TLS v1.1 message (ClientHello is
+# sent prior to negotiating which version will be used)
+#CONFIG_TLSV11=y
+
+# TLS-based EAP methods require at least TLS v1.0. Newer version of TLS (v1.2)
+# can be enabled to enable use of stronger crypto algorithms. It should be
+# noted that some existing TLS v1.0 -based implementation may not be compatible
+# with TLS v1.2 message (ClientHello is sent prior to negotiating which version
+# will be used)
+#CONFIG_TLSV12=y
+
+# If CONFIG_TLS=internal is used, additional library and include paths are
+# needed for LibTomMath. Alternatively, an integrated, minimal version of
+# LibTomMath can be used. See beginning of libtommath.c for details on benefits
+# and drawbacks of this option.
+#CONFIG_INTERNAL_LIBTOMMATH=y
+#ifndef CONFIG_INTERNAL_LIBTOMMATH
+#LTM_PATH=/usr/src/libtommath-0.39
+#CFLAGS += -I$(LTM_PATH)
+#LIBS += -L$(LTM_PATH)
+#LIBS_p += -L$(LTM_PATH)
+#endif
+# At the cost of about 4 kB of additional binary size, the internal LibTomMath
+# can be configured to include faster routines for exptmod, sqr, and div to
+# speed up DH and RSA calculation considerably
+#CONFIG_INTERNAL_LIBTOMMATH_FAST=y
+
+# Include NDIS event processing through WMI into wpa_supplicant/wpasvc.
+# This is only for Windows builds and requires WMI-related header files and
+# WbemUuid.Lib from Platform SDK even when building with MinGW.
+#CONFIG_NDIS_EVENTS_INTEGRATED=y
+#PLATFORMSDKLIB="/opt/Program Files/Microsoft Platform SDK/Lib"
+
+# Add support for old DBus control interface
+# (fi.epitest.hostap.WPASupplicant)
+#CONFIG_CTRL_IFACE_DBUS=y
+
+# Add support for new DBus control interface
+# (fi.w1.hostap.wpa_supplicant1)
+#CONFIG_CTRL_IFACE_DBUS_NEW=y
+
+# Add introspection support for new DBus control interface
+#CONFIG_CTRL_IFACE_DBUS_INTRO=y
+
+# Add support for loading EAP methods dynamically as shared libraries.
+# When this option is enabled, each EAP method can be either included
+# statically (CONFIG_EAP_<method>=y) or dynamically (CONFIG_EAP_<method>=dyn).
+# Dynamic EAP methods are build as shared objects (eap_*.so) and they need to
+# be loaded in the beginning of the wpa_supplicant configuration file
+# (see load_dynamic_eap parameter in the example file) before being used in
+# the network blocks.
+#
+# Note that some shared parts of EAP methods are included in the main program
+# and in order to be able to use dynamic EAP methods using these parts, the
+# main program must have been build with the EAP method enabled (=y or =dyn).
+# This means that EAP-TLS/PEAP/TTLS/FAST cannot be added as dynamic libraries
+# unless at least one of them was included in the main build to force inclusion
+# of the shared code. Similarly, at least one of EAP-SIM/AKA must be included
+# in the main build to be able to load these methods dynamically.
+#
+# Please also note that using dynamic libraries will increase the total binary
+# size. Thus, it may not be the best option for targets that have limited
+# amount of memory/flash.
+#CONFIG_DYNAMIC_EAP_METHODS=y
+
+# IEEE Std 802.11r-2008 (Fast BSS Transition)
+#CONFIG_IEEE80211R=y
+
+# Add support for writing debug log to a file (/tmp/wpa_supplicant-log-#.txt)
+#CONFIG_DEBUG_FILE=y
+
+# Send debug messages to syslog instead of stdout
+#CONFIG_DEBUG_SYSLOG=y
+# Set syslog facility for debug messages
+#CONFIG_DEBUG_SYSLOG_FACILITY=LOG_DAEMON
+
+# Add support for sending all debug messages (regardless of debug verbosity)
+# to the Linux kernel tracing facility. This helps debug the entire stack by
+# making it easy to record everything happening from the driver up into the
+# same file, e.g., using trace-cmd.
+#CONFIG_DEBUG_LINUX_TRACING=y
+
+# Enable privilege separation (see README 'Privilege separation' for details)
+#CONFIG_PRIVSEP=y
+
+# Enable mitigation against certain attacks against TKIP by delaying Michael
+# MIC error reports by a random amount of time between 0 and 60 seconds
+#CONFIG_DELAYED_MIC_ERROR_REPORT=y
+
+# Enable tracing code for developer debugging
+# This tracks use of memory allocations and other registrations and reports
+# incorrect use with a backtrace of call (or allocation) location.
+#CONFIG_WPA_TRACE=y
+# For BSD, uncomment these.
+#LIBS += -lexecinfo
+#LIBS_p += -lexecinfo
+#LIBS_c += -lexecinfo
+
+# Use libbfd to get more details for developer debugging
+# This enables use of libbfd to get more detailed symbols for the backtraces
+# generated by CONFIG_WPA_TRACE=y.
+#CONFIG_WPA_TRACE_BFD=y
+# For BSD, uncomment these.
+#LIBS += -lbfd -liberty -lz
+#LIBS_p += -lbfd -liberty -lz
+#LIBS_c += -lbfd -liberty -lz
+
+# wpa_supplicant depends on strong random number generation being available
+# from the operating system. os_get_random() function is used to fetch random
+# data when needed, e.g., for key generation. On Linux and BSD systems, this
+# works by reading /dev/urandom. It should be noted that the OS entropy pool
+# needs to be properly initialized before wpa_supplicant is started. This is
+# important especially on embedded devices that do not have a hardware random
+# number generator and may by default start up with minimal entropy available
+# for random number generation.
+#
+# As a safety net, wpa_supplicant is by default trying to internally collect
+# additional entropy for generating random data to mix in with the data fetched
+# from the OS. This by itself is not considered to be very strong, but it may
+# help in cases where the system pool is not initialized properly. However, it
+# is very strongly recommended that the system pool is initialized with enough
+# entropy either by using hardware assisted random number generator or by
+# storing state over device reboots.
+#
+# wpa_supplicant can be configured to maintain its own entropy store over
+# restarts to enhance random number generation. This is not perfect, but it is
+# much more secure than using the same sequence of random numbers after every
+# reboot. This can be enabled with -e<entropy file> command line option. The
+# specified file needs to be readable and writable by wpa_supplicant.
+#
+# If the os_get_random() is known to provide strong random data (e.g., on
+# Linux/BSD, the board in question is known to have reliable source of random
+# data from /dev/urandom), the internal wpa_supplicant random pool can be
+# disabled. This will save some in binary size and CPU use. However, this
+# should only be considered for builds that are known to be used on devices
+# that meet the requirements described above.
+#CONFIG_NO_RANDOM_POOL=y
+
+# IEEE 802.11n (High Throughput) support (mainly for AP mode)
+#CONFIG_IEEE80211N=y
+
+# Wireless Network Management (IEEE Std 802.11v-2011)
+# Note: This is experimental and not complete implementation.
+#CONFIG_WNM=y
+
+# Interworking (IEEE 802.11u)
+# This can be used to enable functionality to improve interworking with
+# external networks (GAS/ANQP to learn more about the networks and network
+# selection based on available credentials).
+#CONFIG_INTERWORKING=y
+
+# Hotspot 2.0
+#CONFIG_HS20=y
+
+# AP mode operations with wpa_supplicant
+# This can be used for controlling AP mode operations with wpa_supplicant. It
+# should be noted that this is mainly aimed at simple cases like
+# WPA2-Personal while more complex configurations like WPA2-Enterprise with an
+# external RADIUS server can be supported with hostapd.
+#CONFIG_AP=y
+
+# P2P (Wi-Fi Direct)
+# This can be used to enable P2P support in wpa_supplicant. See README-P2P for
+# more information on P2P operations.
+#CONFIG_P2P=y
+
+# Autoscan
+# This can be used to enable automatic scan support in wpa_supplicant.
+# See wpa_supplicant.conf for more information on autoscan usage.
+#
+# Enabling directly a module will enable autoscan support.
+# For exponential module:
+#CONFIG_AUTOSCAN_EXPONENTIAL=y
+# For periodic module:
+#CONFIG_AUTOSCAN_PERIODIC=y
+
+# Password (and passphrase, etc.) backend for external storage
+# These optional mechanisms can be used to add support for storing passwords
+# and other secrets in external (to wpa_supplicant) location. This allows, for
+# example, operating system specific key storage to be used
+#
+# External password backend for testing purposes (developer use)
+#CONFIG_EXT_PASSWORD_TEST=y

meta-digi-del/recipes-connectivity/wpa-supplicant/wpa-supplicant/ccxmx53js/wpa_supplicant.conf

@@ -0,0 +1,20 @@
+ctrl_interface=/var/run/wpa_supplicant
+ctrl_interface_group=0
+fast_reauth=1
+update_config=1
+
+## -- Example MANAGED network
+ap_scan=1	# for MANAGED mode
+network={
+	scan_ssid=1
+	ssid=""
+	key_mgmt=NONE
+}
+
+## -- Example AD-HOC network
+# ap_scan=2	# mandatory for AD-HOC mode
+# network={
+# 	mode=1
+# 	ssid="adhoc_network"
+# 	key_mgmt=NONE
+# }

meta-digi-del/recipes-connectivity/wpa-supplicant/wpa-supplicant/wpa-supplicant.sh

@@ -16,11 +16,9 @@ else
 fi
 
 if [ ! -x "$WPA_SUP_BIN" ]; then
-	
 	if [ "$VERBOSITY" = "1" ]; then
 		echo "$WPA_SUP_PNAME: binaries not executable or missing from $WPA_SUP_BIN"
 	fi
-	
 	exit 1
 fi
 
@@ -29,21 +27,19 @@ if [ "$MODE" = "start" ] ; then
 	if [ -s "/etc/wpa_supplicant/driver.$IFACE" ]; then
 		IF_WPA_DRIVER=$(cat "/etc/wpa_supplicant/driver.$IFACE")
 	elif [ -z "$IF_WPA_DRIVER" ]; then
-		
+
 		if [ "$VERBOSITY" = "1" ]; then
 			echo "$WPA_SUP_PNAME: wpa-driver not provided, using \"wext\""
 		fi
-		
+
 		IF_WPA_DRIVER="wext"
 	fi
-	
+
 	# if we have passed the criteria, start wpa_supplicant
 	if [ -n "$WPA_SUP_CONF" ]; then
-		
 		if [ "$VERBOSITY" = "1" ]; then
 			echo "$WPA_SUP_PNAME: $WPA_SUP_BIN $WPA_SUP_OPTIONS $WPA_SUP_CONF -D $IF_WPA_DRIVER"
 		fi
-		
 		start-stop-daemon --start --quiet \
 			--name $WPA_SUP_PNAME --startas $WPA_SUP_BIN --pidfile $WPA_SUP_PIDFILE \
 			--  $WPA_SUP_OPTIONS $WPA_SUP_CONF -D $IF_WPA_DRIVER
@@ -51,35 +47,28 @@ if [ "$MODE" = "start" ] ; then
 
 	# if the interface socket exists, then wpa_supplicant was invoked successfully
 	if [ -S "$WPA_COMMON_CTRL_IFACE/$IFACE" ]; then
-	
 		if [ "$VERBOSITY" = "1" ]; then
 			echo "$WPA_SUP_PNAME: ctrl_interface socket located at $WPA_COMMON_CTRL_IFACE/$IFACE"
 		fi
-
 		exit 0
-		
 	fi
-	
 elif [ "$MODE" = "stop" ]; then
-
 	if [ -f "$WPA_SUP_PIDFILE" ]; then
-		
 		if [ "$VERBOSITY" = "1" ]; then
 			echo "$WPA_SUP_PNAME: terminating $WPA_SUP_PNAME daemon"
 		fi
-		
+
 		start-stop-daemon --stop --quiet \
 			--name $WPA_SUP_PNAME --pidfile	$WPA_SUP_PIDFILE
-			
+
 		if [ -S "$WPA_COMMON_CTRL_IFACE/$IFACE" ]; then
 			rm -f $WPA_COMMON_CTRL_IFACE/$IFACE
 		fi
-			
+
 		if [ -f "$WPA_SUP_PIDFILE" ]; then
 			rm -f $WPA_SUP_PIDFILE
 		fi
 	fi
-
 fi
 
 exit 0

meta-digi-del/recipes-connectivity/wpa-supplicant/wpa-supplicant_1.0.bbappend

@@ -1,4 +0,0 @@
-FILESEXTRAPATHS_prepend := "${THISDIR}/${PN}-${PV}"
-
-PR_append = "+${DISTRO}.r0"
-

meta-digi-del/recipes-connectivity/wpa-supplicant/wpa-supplicant_2.0.bb

@@ -0,0 +1,6 @@
+require wpa-supplicant-2.0.inc
+
+PR = "${DISTRO}.r0"
+
+SRC_URI[md5sum] = "3be2ebfdcced52e00eda0afe2889839d"
+SRC_URI[sha256sum] = "2c115609fbb5223d51381084a5c944455a8afcda81d584173ff55ba233379e09"

meta-digi-del/recipes-connectivity/wpa-supplicant/wpa-supplicant_6ffdc2f.bb

@@ -1,10 +0,0 @@
-# Copyright (C) 2012 Digi International.
-
-require wpa-supplicant.inc
-
-PR = "r0"
-
-SRC_URI += "${DIGI_LOG_MIRROR}wpa_supplicant-${PV}.tar.gz"
-
-SRC_URI[md5sum] = "99f8c4ce691e3c19b5cfc040efdadfe9"
-SRC_URI[sha256sum] = "eaa94b450ed1e2e02f7f2ee31f86c873219603cd29d791c3dda5be0250ea7f7e"