diff --git a/meta-digi-arm/recipes-bsp/firmware-qualcomm/firmware-qualcomm/wlan/cfg.dat b/meta-digi-arm/recipes-bsp/firmware-qualcomm/firmware-qualcomm/wlan/cfg.dat deleted file mode 100644 index 3860af48e..000000000 Binary files a/meta-digi-arm/recipes-bsp/firmware-qualcomm/firmware-qualcomm/wlan/cfg.dat and /dev/null differ diff --git a/meta-digi-arm/recipes-bsp/firmware-qualcomm/firmware-qualcomm/wlan/qcom_cfg.ini b/meta-digi-arm/recipes-bsp/firmware-qualcomm/firmware-qualcomm/wlan/qcom_cfg.ini deleted file mode 100644 index fd1a774a1..000000000 --- a/meta-digi-arm/recipes-bsp/firmware-qualcomm/firmware-qualcomm/wlan/qcom_cfg.ini +++ /dev/null @@ -1,373 +0,0 @@ -# This file allows user to override the factory - -# defaults for the WLAN Driver - -# Debug tracing bit values -# VOS tracing requires a debug build - see BUILD_DEBUG_VERSION - -# None = 0 -# Error -# Warn -# Info -# Info high -# Info med -# Info low -# Debug = 7 - -# Debug masks in decimal -# Default debug is Error and Warn 0x06 (6) -# All debug is 0xff (255) - -#vosTraceEnableTL=6 -#vosTraceEnableWDI=6 -#vosTraceEnableHDD=6 -#vosTraceEnableSME=6 -#vosTraceEnablePE=6 -#vosTraceEnablePMC=6 -#vosTraceEnableWDA=6 -#vosTraceEnableSYS=6 -#vosTraceEnableVOSS=6 -#vosTraceEnableSAP=6 -#vosTraceEnableHDDSAP=6 - -# Enable/Disable Idle Scan - -gEnableRxThread=1 - - -# Increase sleep duration (seconds) during IMPS -# 0 implies no periodic wake up from IMPS. Periodic wakeup is -# unnecessary if Idle Scan is disabled. -gImpsModSleepTime=0 - - -# Enable suspend or not - -# 1: Enable standby, 2: Enable Deep sleep, 3: Enable Mcast/Bcast Filter - -gEnableSuspend=3 - - -# Phy Mode (auto, b, g, n, etc) -# Valid values are 0-9, with 0 = Auto, 4 = 11n, 9 = 11ac -# 1 = 11abg, 2 = 11b, 3 = 11g, 5 = 11g only, 6 = 11n only -# 7 = 11b only 8 = 11ac only. -gDot11Mode=0 - -# CSR Roaming Enable(1) Disable(0) - -gRoamingTime=0 - -# Assigned MAC Addresses - This will be used until NV items are in place - -# Each byte of MAC address is represented in Hex format as XX - -Intf0MacAddress=000AF58989FF -Intf1MacAddress=000AF58989FE -Intf2MacAddress=000AF58989FD - -Intf3MacAddress=000AF58989FC - - -# UAPSD service interval for VO,VI, BE, BK traffic - -InfraUapsdVoSrvIntv=0 - -InfraUapsdViSrvIntv=0 - -InfraUapsdBeSrvIntv=0 - -InfraUapsdBkSrvIntv=0 - -# Flag to allow STA send AddTspec even when ACM is Off -gAddTSWhenACMIsOff=1 - -# Make 1x1 the default antenna configuration - -gNumRxAnt=1 - - -# Beacon filtering frequency (unit in beacon intervals) - -gNthBeaconFilter=50 - - -# Flags to filter Mcast abd Bcast RX packets. - -# Value 0: No filtering, 1: Filter all Multicast. - -# 2: Filter all Broadcast. 3: Filter all Mcast abd Bcast - -McastBcastFilter=3 - - -#Flag to enable HostARPOffload feature or not - -hostArpOffload=1 - -#Flag to enable HostNSOffload feature or not - -hostNSOffload=1 - -#Enable OBSS protection - -gEnableApOBSSProt=1 - - -# RTS threshold - -RTSThreshold=1048576 - - -# DFS Master Capability -gEnableDFSMasterCap=1 - -# fast transition -ImplicitQosIsEnabled=0 - -gNeighborLookupThreshold=76 - -#Check if the AP to which we are roaming is better than current AP in terms of RSSI. -#Checking is disabled if set to Zero.Otherwise it will use this value as to how better -#the RSSI of the new/roamable AP should be for roaming -RoamRssiDiff=3 - -# SAP auto channel selection configuration - -# 0 = disable auto channel selection - -# 1 = enable auto channel selection, channel provided by supplicant will be ignored - -gApAutoChannelSelection=0 - - -# Listen Energy Detect Mode Configuration - -# Valid values 0-128 - -# 128 means disable Energy Detect feature - -# 0-9 are threshold code and 7 is recommended value from system if feature is to be enabled. - -# 10-128 are reserved. - -# The EDET threshold mapping is as follows in 3dB step: - -# 0 = -60 dBm - -# 1 = -63 dBm - -# 2 = -66 dBm - -# ... - -# 7 = -81 dBm - -# 8 = -84 dBm - -# 9 = -87 dBm - -# Note: Any of these settings are valid. Setting 0 would yield the highest power saving (in a noisy environment) at the cost of more range. The range impact is approximately #calculated as: - -# - -# Range Loss (dB) = EDET threshold level (dBm) + 97 dBm. - -# - -gEnablePhyAgcListenMode=128 - - -#SOFTAP Channel Range selection - -gAPChannelSelectStartChannel=1 - -gAPChannelSelectEndChannel=11 - - -#SOFTAP Channel Range selection Operating band - -# 0:2.4GHZ 1: LOW-5GHZ 2:MID-5GHZ 3:HIGH-5GHZ 4: 4.9HZ BAND - -gAPChannelSelectOperatingBand=0 - - -#Channel Bonding -gChannelBondingMode5GHz=1 - - -#Enable Keep alive with non-zero period value - -gStaKeepAlivePeriod = 30 - -#Say gGoKeepAlivePeriod(5 seconds) and gGoLinkMonitorPeriod(10 seconds). -#For every 10 seconds DUT send Qos Null frame(i.e., Keep Alive frame if link is idle for last 10 seconds.) -#For both active and power save clients. - -#Power save clients: DUT set TIM bit from 10th second onwards and till client honors TIM bit. -#If doesn't honor for 5 seconds then DUT remove client. - -#Active clients: DUT send Qos Null frame for 10th seconds onwards if it is not success still we try on -#11th second if not tries on 12th and so on till 15th second. Hence before disconnection DUT will send 5 NULL frames. -#Hence in any case DUT will detect client got removed in (10+5) seconds. i.e., (gGoKeepAlivePeriod + gGoLinkMonitorPeriod).. - -#gGoLinkMonitorPeriod/ gApLinkMonitorPeriod is period where link is idle and it is period -#where we send NULL frame. - -#gApLinkMonitorPeriod = 10 - -#gGoLinkMonitorPeriod = 10 - -#gGoKeepAlivePeriod/gApKeepAlivePeriod is time to spend to check whether frame are succeed to send or not. -#Hence total effective detection time is gGoLinkMonitorPeriod+ gGoKeepAlivePeriod/gApLinkMonitorPeriod+ gApKeepAlivePeriod. - - -gGoKeepAlivePeriod = 20 - -gApKeepAlivePeriod = 20 - - -gEnableLogp=1 - - -# 0 for OLPC 1 for CLPC and SCPC -gEnableCloseLoop=1 - -#Data Inactivity Timeout when in powersave (in ms) -gDataInactivityTimeout=200 - -# VHT Tx/Rx MCS values -# Valid values are 0,1,2. If commented out, the default value is 0. -# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 -gVhtRxMCS=2 -gVhtTxMCS=0 - -# VHT Tx/Rx MCS values for 2x2 -# Valid values are 0,1,2. If commented out, the default value is 0. -# 0=MCS0-7, 1=MCS0-8, 2=MCS0-9 -gEnable2x2=0 -gVhtRxMCS2x2=2 -gVhtTxMCS2x2=2 - -# Set txchainmask and rxchainmask -# These parameters are used only if gEnable2x2 is 0 -# Valid values are 1,2 -# Set gSetTxChainmask1x1=1 or gSetRxChainmask1x1=1 to select chain0. -# Set gSetTxChainmask1x1=2 or gSetRxChainmask1x1=2 to select chain1. -gSetTxChainmask1x1=1 -gSetRxChainmask1x1=1 - -# 1=enable STBC; 0=disable STBC -gEnableRXSTBC=1 - -# 1=enable tx STBC; 0=disable -gEnableTXSTBC=1 - -# 1=enable rx LDPC; 0=disable -gEnableRXLDPC=1 - -#Enable Scan Results Aging based on timer -#Timer value is in seconds -#If Set to 0 it will not enable the feature -gScanAgingTime=0 - -#Enable Scan Results Aging based on number of scans -gScanResultAgeCount=1 - -#Enable thermal mitigation -gThermalMitigationEnable=0 - -#Thermal Mitigation Levels -gThermalTempMinLevel0=0 -gThermalTempMaxLevel0=107 -gThermalTempMinLevel1=105 -gThermalTempMaxLevel1=117 -gThermalTempMinLevel2=110 -gThermalTempMaxLevel2=127 -gThermalTempMinLevel3=115 -gThermalTempMaxLevel3=0 - -#Maxium Channel time in msec -gMaxMediumTime = 6000 - -# 802.11K support -gRrmEnable=1 -gRrmOperChanMax=8 -gRrmNonOperChanMax=8 - -#Scan offload -gEnableDirectedScanOffload=1 - -#Enable Power Save offload -gEnablePowerSaveOffload=1 - -#Enable firmware log -gEnablefwlog=1 - -#P2P Listen offload -gEnableP2pListenOffload=1 - -# Maximum Receive AMPDU size (VHT only. Valid values: 0->8k 1->16k 2->32k 3->64k 4->128k) -gVhtAmpduLenExponent=7 - -# Maximum MPDU length (VHT only. Valid values: 0->3895 octets, 1->7991 octets, 2->11454 octets) -gVhtMpduLen=2 - -# Maximum number of wow filters required -#gMaxWoWFilters=22 - -# WOW Enable/Disable. -# 0 - Disable both magic pattern match and pattern byte match. -# 1 - Enable magic pattern match on all interfaces. -# 2 - Enable pattern byte match on all interfaces. -# 3 - Enable both magic patter and pattern byte match on all interfaces. -# Default value of gEnableWoW is 3. -# gEnableWoW=0 - -#Enable or Disable p2p device address administered -isP2pDeviceAddrAdministrated=0 - -# Set Thermal Power limit -TxPower2g=10 -TxPower5g=10 - -#Enable VHT on 2.4Ghz -gEnableVhtFor24GHzBand=1 - -#Enable or Disable 5G early beacon termination -gEnable5gEBT=1 - -ssdp = 0 - -#Enable Hysteretic mode -gEnableHystereticMode=1 - -# Bus bandwidth compute timeout value in ms -gBusBandwidthComputeInterval=2000 - -# Regulatory Setting; 0=STRICT; 1=CUSTOM -gRegulatoryChangeCountry=1 - -# Enable/Disable RX full reorder offload -gReorderOffloadSupported=1 - -#Set SAP max peer to 16 which allows 10 WEP connection -gSoftApMaxPeers=16 - -# Whether userspace country code setting shld have priority -gCountryCodePriority=1 - -# Enable(1)/Disable(0) SIFS burst -gEnableSifsBurst=1 - -# Enable or Disable Multi-user MIMO -# 1=Enable (default), 0=Disable -gEnableMuBformee=1 - -# Inactivity time (in ms) to end TX Service Period while in IBSS power save mode -gIbssTxSpEndInactivityTime=10 - -END - -# Note: Configuration parser would not read anything past the END marker -