The LEGACY_IMAGE_FORMAT defaults to 'y' if there is no FIT
support, which happens after applying the default configuration.
Then, the FIT support is added in a config fragment, but the
LEGACY_IMAGE_FORMAT is not disabled.
Disabling this is recommended to avoid the possibility to boot
unsigned legacy images.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The U-Boot bootscript loads the fitImage into RAM memory to run
this bootscript. This bootscript ends up calling 'dboot' command
to run the FIT default configuration.
To avoid 'dboot' re-loading again the fitImage into RAM memory,
set this temporary variable that will be immediately reset
by 'dboot'.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
This commit adds several overlays for DVK v2 and modifies the boot script to apply it
based on the board_version variable.
https://onedigi.atlassian.net/browse/DEL-8746
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit adds signed FIT image support for the CCMP1
platforms when using Trustfence.
https://onedigi.atlassian.net/browse/DEL-8591
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
Use the intention of installing dual boot firmware as a condition to set
bootlimit=3 so that the bootcount mechanism is enabled.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DUB-1058
During firmware install, the target may be reset several times.
We don't want the bootcount to count these as boot attempts.
This was done in a791bb4463 for the ccmp1
but not for the rest of platforms.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Improve boot attempts message showing not only the current boot attempt
but also the limit:
(boot attempt 1/3)
Print the message only when the bootcount mechanism is active, i.e. when
the bootlimit is defined (not zero), and when bootcount is > 0.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DUB-1056
If the default r/w rootfs is not found it will try to do a
fallback to the squashfs image.
In the nand devices additionally we need to set the rootfstype
to squashfs.
https://onedigi.atlassian.net/browse/DEL-8638
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
When booting from a microSD, the variable 'boot_device' is
set to "mmc". Check this to fall back to booting Linux from
the microSD partitions.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Until now, for dualboot systems, all boot variables were calculated on each boot depending on the value of the
'active_system'. These variables are used to boot the device but were not saved, which could lead to a missmatch
between their value in the environment and their required values to correctly boot the system. This commit
simplifies a bit the variables calculation and adds a block to synchronize their value in the environment.
Signed-off-by: David Escalona <david.escalona@digi.com>
All the 'altboot' script functionality has been moved directly to the 'altbootcmd' command
in U-Boot, so this script is no longer necessary. Remove it for all platforms.
https://onedigi.atlassian.net/browse/DEL-8674
Signed-off-by: David Escalona <david.escalona@digi.com>
The install scripts from SD/USB use a fixed image name.
If you are trying to install a different image you need to set
the env variable 'image-name' first.
Add a helper message if default files are not found to
avoid needing to go to the documentation.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
During firmware install, the target may be reset several times.
We don't want the bootcount to count these as boot attempts.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The 'bootcount' value is now incremented and stored in the system on every boot and
not only then the 'upgrade_available' flag is set. Also, ensure the value is cleared
when the 'altboot' script is executed by running the new U-Boot command 'bootcount reset'.
https://onedigi.atlassian.net/browse/DEL-8506
Signed-off-by: David Escalona <david.escalona@digi.com>
When booting from recovery sdcard, in the imx93 the dualboot is yes by
default, so the mmcroot variable was not set correctly for the uSD.
If we boot from uSD, just assume all the system is in the uSD card, whether
it is a recovery system or a prepared uSD card for demo.
https://onedigi.atlassian.net/browse/DEL-8461
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
We no longer need logic to determine the SOM's RAM size and bus width, we only
need to know the SOC revision, which is info that is always available.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit modifies the boot script condition to apply the overlay for MCA
based on HWID MCA field.
https://onedigi.atlassian.net/browse/DEL-8521
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit modifies the boot script condition to apply the overlay for DVK v1
on boards without the board_version variable defined.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit adds an overlay for DVK v1 and modifies the boot script to apply it
based on the board_version variable.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Partitions 'fip-a' and 'fip-b' are redundant at the moment. They are
not currently part of the dualboot system. In consequence, program
both partitons unconditionally during the install process.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Number of bootup logos is now configured using fbcon=logo-count parameter,
so use it instead of our deprecated custom code in the kernel.
For backwards compatibility, we add this parameter in the u-boot boot
script for all platforms but the ccimx93, where this is directly handled
by u-boot (v2022.04).
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This reverts commit 2bdfdc92e1.
This suffix was removed on error. The artifact does have the suffix.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
These are just a verbatim copy of the ccimx8mm ones, so the project is
buildable. This file list should be revisited and adapted for the
ccimx93.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Increase the timeout from 90 to 120s since it's a large image
and it may take more time on different NANDs.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The U-Boot environment resides on a UBI volume. The uuu script
relies on the environment to save part of the commands that
U-Boot needs to execute after reboot in the middle of the
installation. If the UBI volume 'uboot_config' does not exist
the installer fails.
This commit:
- Creates a function -on the uuu script only- for obtaining
the result of running any U-Boot command (0=success, 1=error).
- Checks the existance of 'uboot_config' volume.
- Runs 'ubivolscript' script to create the UBI volumes layout
that generates the environment volume if it doesn't exist.
- Increases the timeout for running the 'ubivolscript' since
there are occasions in which 'ubi part' (which is part of the
script) takes more time (if it cannot find the fastmap).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
By default ccmp1 platforms have dualboot mode by default, however the required
boot script was added to ccmp15 platform only, so this commit fixes it.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The first time the 'dualboot' variable is tested it is directly run in
the script and doesn't need to escape the special characters.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
When Dual Boot is not enabled, 'rootfsvol' variable must point to the
single boot system rootfs partition 'rootfs'.
Explicitly set this value. Otherwise the script relays on the default
rootfsvol value, which may be a Dual Boot partition.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
- create dualboot.bbclass that
- sets DUALBOOT_ENABLED variable
- defines partition names and function for changing the sw-description
for swupdate
- move files from layer into meta-digi
https://onedigi.atlassian.net/browse/DEL-7962
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
On the CCMP1 SOMs, we only consider a single system partition called UBI,
with many UBI volumes.
The variable 'singlemtdsys' allowed to change between this and
a system with multiple MTD partitions with one UBI volume each
(old approach on CC6UL).
This commit removes the variable and uses the logic as if it was set.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
For the CC6UL 1GB flash variant, the programming of the rootfs exceeds
the current 90 secs timeout, giving following failure:
[Bulk(R):LIBUSB_ERROR_TIMEOUT] fb[-t 90000]: ucmd update rootfs ram ${fastboot_buffer} ${fastboot_bytes} -e
Error: Bulk(R):LIBUSB_ERROR_TIMEOUT
Increase the timeout to prevent the failure.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
(cherry picked from commit 16eded4f0edcc603de83be7155f7c09718ba5ddd)
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This commit adds u-boot build support for the CCMP15 platform.
The installation scripts are copies from the CC6UL platform.
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
https://onedigi.atlassian.net/browse/DEL-7797
U-Boot uses partition names instead of partition indexes for the nand devices.
This commit syncs the boot scripts with the new dualboot variables.
https://onedigi.atlassian.net/browse/CC6UL-1254
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Add missing call to 'uuu' and erase the partition before creating
the UBI volumes.
Also add larger timeouts to erase operations.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The variable 'dualboot' (and 'singlemtdsys' for CC6UL) was restored
after the bootcmd that runs the first time after programming U-Boot runs
fastboot again to resume the script.
This is ok for the CC6UL but not for the rest of platforms, that run the
partition script on the bootcmd, *before* running fastboot.
Restore the variables for all platforms in the bootcmd right after
resetting the environment.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
U-Boot has embedded support to handle bootcount tries.
When the limit of tries is reached, U-Boot runs the script
in `altbootcmd` rather than the usual `bootcmd`.
This other script resides on meta-digi-dualboot layer.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
Ensure stdout redirection to the USB interface is removed in every case.
Otherwise, it would be left redirected when INSTALL_UBOOT_FILENAME is
manually set.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Install scripts may rework the partition table basing on the value of
env variables. Information of UBI volumes may remain on the NAND that
could later not correspond to the new partition table.
Make sure the MTD partitions are erased prior to updating:
- For Multi-MTD, append '-e' option to the update command.
- For Single-MTD, erase the system partition.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Check the status of 'dualboot' env variable.
If set to "yes", use the dualboot partition table in the script and
restore the variable (default is "no") after resetting the environment.
Also, for dualboot, there's no need to wipe the recovery partition or
boot into recovery mode.
For dualboot, this script programs both systems A and B with the same
images.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-7649
When DualBoot mechanism is enabled and an update is pending,
the boot script needs to change certain variables and save the
environment.
The regular boot script already changes a number of variables,
such as 'extra_bootargs' and 'overlays' by appending strings to
the already existing values. Saving the envionment may make these
grow endlessly with each iteration of the boot script.
For this reason, move the DualBoot check as the first thing in
the script, save the environment if needed, and then continue
with the normal flow, that changes variables before booting
but doesn't save them.
On certain scripts, this allows us to get rid of some instructions
for resetting the overlays variable.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The script required the passing of option '-b' for setting up the
target to use a single MTD partition and multiple UBI volumes.
If a target however already has the variable 'ubisysvols' set to
'yes' but this parameter is forgotten when calling the script, the
partition layout would change to default (several MTD partitions).
Remove the recently added '-b' option and make the script decide
basing on the current value of 'ubisysvols' variable.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The script preserves the current value of env variable 'ubisysvols'
so that the new partition script generates the appropriate partition
table before proceeding with the update operations.
If using a UBI volumes layout, the script will not erase the partitions.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-7614
With U-Boot supporting the creation of mtdparts and UBI volumes depending
on the value of variable 'ubisysvols', adapt the install script to make
use of those to generate a partition table and UBI volumes accordingly.
This can be triggered with new option '-b'.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Set the new variable 'rootfsvol' to rootfs_a or rootfs_b when dualboot is
enabled, to cover the case where the devices uses the 'system' partition
with different UBI volumes.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The support for dualboot was integrated on meta-digi-dualboot layer, but it
really depends only on environment variable 'dualboot' so we'd better
integrate the support on the scripts in meta-digi, to avoid synchonization
problems between both layers.
This also allows to be able to easily enable dualboot in U-Boot with the
variable, without needing to update the script on the linux partition.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
This command was already present on the script used for CC8X. Add it here
so the scripts are as much alike as possible.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Fastboot is configured on boot with the current MMC configuration.
If we create a GPT partition table, we need to restart fastboot before we
try to program any partition with the 'flash' fastboot command.
Set 'fastboot_dev' to a different device, 'sata' for example an back to 'mmc'
to trigger a fastboot restart after creating the partition table on blank
devices.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
The current syntax only works properly when running the script through bash.
Change this so that it works for other shells as well.
While at it, fix a typo in the message that appears when the variant can't be
detected in the 6UL script.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
We document how to use this script from the Yocto image directory. Now that the
*.ext4 files are compressed by default, the script needs to automatically
decompress said files before starting the update process.
https://onedigi.atlassian.net/browse/DEL-7582
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The install script of cc8x had errors (using double '==' instead
of single on comparisions).
Besides fixing this typo, this commit changes the logic to:
- default to 2GB U-Boot for variants other than the ones in the
list.
- consider variant code 0x00 (not programmed HWID) as a failure.
thus forcing the user to specify the file on the command line.
This second action is done also on the cc6ul script.
Reported-by: Hector Bujanda <hector.bujanda@digi.com>
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
install_abort is a temp variable so 'test -n' doesn't work on it.
This was fixed in all scripts except the USB script of ccimx6sbc.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
- Check the existence of files before the 10 second wait.
- Print the list of filenames to program to each partition.
- Print the file that's being updated to each partition.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
With the generalization done in previous commits, we have now several files
that are identical and can be merged into a common SOM or SOM family
folder.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Create global variables:
DEFAULT_IMAGE_NAME
GRAPHICAL_IMAGES
to have them substituted on the U-Boot install scripts for better
generalization.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
U-Boot install scripts (from uSD and USB) were hard-coded to dey-image-qt.
Allow to install other image files by setting a new variable 'image-name'
which defaults to 'dey-image-qt' if not defined, except for the CC6UL
SBC Express, that defaults to 'core-image-base'.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7385https://jira.digi.com/browse/DEL-7333
On these boot scripts, this variable is not used, so we can remove it.
Besides, it's generated by U-Boot code.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Use ##MACHINE## placeholder to have it later substituted by the recipe
using Yocto ${MACHINE} variable.
This will help later reducing the number of files to have one per SOM
(or even family) instead of one per platform.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Non-graphical images (core-image-base, dey-image-aws) don't contain the
graphic-backend on their filenames.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
- Determine first the filenames and abort if any does not exist.
- Print a warning message about the erasing of the media with a list
of partitions and files to use for the update
- Sync the different scripts so they look more similar
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7333
Similar to how it's done on the ccimx6ul, create a function for updating
a partition with a file, that also prints a message.
Rename the function to be the same in all scripts.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7333
Previously, this script only allowed the U-Boot filename as parameter.
This commit makes use of getopts() to pass the following options to the
script:
-h, for help
-i, to pass the dey image name that prefixes the firmware filenames
-n, to skip the 10 seconds delay that allow you to cancel the process
-u, to pass the U-Boot filename
The default image name (if none passed) keeps being 'dey-image-qt' but the
new option allows reusing this script to install dey-image-webkit or
dey-image-aws images.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7385
This overlay added cooling devices for all quad cores.
On the latest BSP, the SoC device tree include contains all four
cooling devices and the newest U-Boot is able to delete the nodes
for non-existing cores, so there's no need for this overlay
anymore.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
When manually changing the partition table, it could happen that
a UBI volume already exists in the 'update' partition.
If not erased, the system may find the old UBI volume (with wrong
geometry information) and try to mount it which will result in
failure.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
On commit 1e5cafeb79 a fall-back
update command was introduced in case the newest command fails.
If the newest command succeeds, however, the 'test' command for
error doesn't match (there is no error) and the return code of
such test is "1". On the next check for errors, this results on
an error, when we really mean to continue because the first
command was successful.
Move the second error check inside the error path of the first
attempt.
Reported-by: Francisco Gil <francisco.gilmartinez@digi.com>
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Hector Bujanda
Hector Palacios
Arturo Buzarra
Javier Viguera
Mike Engel
Isaac Hermida
Francisco Gil
David Escalona
Gabriel Valcazar
Tatiana Leon
Gonzalo Ruiz