This commit fixes the pulseaudio recipe to launch the pulseaudio-server
service at boot time for sysvinit systems.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This patch has been integrated in meta-freescale's bbappend for
pulseaudio, so having it also in our bbappend results in Yocto trying to
apply it twice, which obviously fails and breaks the build.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Add custom NXP daemon.conf, new NXP patch and adapt ccimx6ulsbc patch to apply
cleanly over v14.2
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The default service only starts once per non-root user. Add a service that
starts pulseaudio by default along with a wrapper script that sets the
necessary environment variables before launching the daemon.
https://jira.digi.com/browse/DEL-6746
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Add pulseaudio audio profile for MAX98089 sound card and
generalize the recipe to support multiple platforms with
the same audio sound card.
https://jira.digi.com/browse/DEL-6461
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit modifies different recipes to support the new platform
ccimx6qpsbc and adapt it to maintain the support to ccimx6sbc.
https://jira.digi.com/browse/DEL-5082
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Pulseaudio 9.0 relies on the syscall memfd_create, which was introduced
in kernel 3.17, but the version currently supported for the CC6 SBC is
3.14.
There is a corner case where the configure script does not detect the
actual kernel version, thus enabling memfd_create. When Pulseadio tries
to call memfd_create, it shows error messages, so disable memfd
explicitly.
https://jira.digi.com/browse/DEL-3923
Signed-off-by: Alejandro Navarro <alejandro.navarro@digi.com>
In pulseaudio, module-suspend-on-idle controls how much time a sink spends
in the 'idle' state before going to 'suspended'. This means the ALSA device
associated with the sink stays busy for a few seconds after loading or using
the sink.
This commit adds the timeout=0 parameter when loading module-suspend-on-idle.
Now the sink will go to the 'suspended' state right after being loaded or used.
https://jira.digi.com/browse/DEL-2218
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
On boot, pulseaudio looks for the sound cards' corresponding profile sets, and
uses a default configuration if none is found. This was causing pulseaudio to
take up to 5 seconds trying every possible default profile.
This commit fixes this by creating a specific profile set for each of the sound
cards on the ccimx6sbc so pulseaudio doesn't spend time trying different
profiles that don't apply to our platform. It also adds udev rules so
pulseaudio knows which configuration to load for each card.
https://jira.digi.com/browse/DEL-2218
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The HDMI hotplug script required alsa-utils to be installed in order to work.
This commit avoids this by adding a recipe for a small binary that replaces
aplay in the script.
https://jira.digi.com/browse/DEL-3482
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
When hotplugging the HDMI cable after booting the target, pulseaudio doesn't
load the HDMI sink. This commit fixes this by adding a udev rule and a script
that prompts pulseaudio to detect the HDMI sound card and load its sink, as
well as making it the default one.
If alsa-utils is available, a faulty command is run to load the card without
any audio output. Otherwise, module-udev-detect is unloaded and reloaded.
This is based on commit fca507d316.
https://jira.digi.com/browse/DEL-2327
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Some platforms, like ccimx6ulsbc, don't support jack detection
out of the box.
PulseAudio will mute the Headphones by default if it believes
there is no headphones jack plugged-in. With this patch we
tell it to preserve ALSA default value for the headphones
controls.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-3435
Using module-detect there are some audio reverb problems. Reverting that commit
will make pulseaudio use module-udev-detect again instead, which takes longer
to initialize but does not have that problem.
This reverts commit e021f738ee.
https://jira.digi.com/browse/DEL-2587
Signed-off-by: Jose Diaz de Grenu de Pedro <Jose.DiazdeGrenudePedro@digi.com>
When module-alsa-sink is used, the audio is sometimes heard with
reverb. We will go back to module-udev-detect, so the functionality
introduced in the commit being reverted won't longer work.
This reverts commit fca507d316.
https://jira.digi.com/browse/DEL-2587
Signed-off-by: Jose Diaz de Grenu de Pedro <Jose.DiazdeGrenudePedro@digi.com>
The ccimx6ul or ccardimx28 do not have hdmi interface, so do not install the
hdmi hotplug script.
https://jira.digi.com/browse/DEL-2654
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
This patch adds a udev rule and a script to detect HDMI hotplug and create
the HDMI audio pulseaudio sink if needed (that is, if the system was
booted with no HDMI cable plugged).
https://jira.digi.com/browse/DEL-2327
Signed-off-by: Jose Diaz de Grenu de Pedro <Jose.DiazdeGrenudePedro@digi.com>
module-udev-detect blocks the sound interface on boot for about five
seconds while detecting the hardware. This patch removes it so that
module-detect is used instead, which uses static hardware detection and is
faster.
https://jira.digi.com/browse/DEL-2218
Signed-off-by: Jose Diaz de Grenu de Pedro <Jose.DiazdeGrenudePedro@digi.com>
Arturo Buzarra
Javier Viguera
Mike Engel
Gabriel Valcazar
Alejandro Navarro
Hector Palacios
Diaz de Grenu, Jose
Isaac Hermida
Jose Diaz de Grenu de Pedro