This overlay contains a workaround to make the USB-OTG
work as USB device when connected to a host.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-9610
(cherry picked from commit ec92f5fdd10a61e37ac3778d0d3aa1816bc6b0aa)
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Device tree overlays now have the extension 'dtso' that
distinguishes them from board 'dts' files, so there is
no need for a prefix '_ov_' to tell if a file contains
a DT overlay.
To make them shorter and easier to tell the platform they
are for, change the filename format to:
<platform-name>_<functionality>.dtso
where <platform-name> can be the name of the SOM or the
name of the DVK, so there is no need either to specify
'som' or 'board' on the filename.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The U-Boot bootscript loads the fitImage into RAM memory to run
this bootscript. This bootscript ends up calling 'dboot' command
to run the FIT default configuration.
To avoid 'dboot' re-loading again the fitImage into RAM memory,
set this temporary variable that will be immediately reset
by 'dboot'.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
This commit adds several overlays for DVK v2 and modifies the boot script to apply it
based on the board_version variable.
https://onedigi.atlassian.net/browse/DEL-8746
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Improve boot attempts message showing not only the current boot attempt
but also the limit:
(boot attempt 1/3)
Print the message only when the bootcount mechanism is active, i.e. when
the bootlimit is defined (not zero), and when bootcount is > 0.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DUB-1056
When booting from a microSD, the variable 'boot_device' is
set to "mmc". Check this to fall back to booting Linux from
the microSD partitions.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Until now, for dualboot systems, all boot variables were calculated on each boot depending on the value of the
'active_system'. These variables are used to boot the device but were not saved, which could lead to a missmatch
between their value in the environment and their required values to correctly boot the system. This commit
simplifies a bit the variables calculation and adds a block to synchronize their value in the environment.
Signed-off-by: David Escalona <david.escalona@digi.com>
The 'bootcount' value is now incremented and stored in the system on every boot and
not only then the 'upgrade_available' flag is set. Also, ensure the value is cleared
when the 'altboot' script is executed by running the new U-Boot command 'bootcount reset'.
https://onedigi.atlassian.net/browse/DEL-8506
Signed-off-by: David Escalona <david.escalona@digi.com>
When Dual Boot is not enabled, 'rootfsvol' variable must point to the
single boot system rootfs partition 'rootfs'.
Explicitly set this value. Otherwise the script relays on the default
rootfsvol value, which may be a Dual Boot partition.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Hector Palacios
Arturo Buzarra
David Escalona
Gonzalo Ruiz