Remove the linux-v4.20 recipe and use the linux-fslc kernel recipe in
meta-freescale-3rdparty instead.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Just add the following to the conf/local.conf file:
MACHINEOVERRIDES .= ":use-mainline-bsp"
The defconfig is the mainline imx_v6_v7_defconfig.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
This adds support for U-Boot v2017.03 for all platforms (including CC8X).
For legacy v2015.04:
- Renames u-boot.inc as a versioned file only for v2015.04.
- Moves boot/install scripts from versioned folder into non-versioned
folder (since the scripts remain the same between versions).
For new v2017.03:
- Re-uses poky's u-boot.inc in rocko for v2017.03
- DEY recipe re-writes the do_compile for special U-Boot configuration
required for TrustFence.
- DEY recipe appends the do_deploy, for U-Boot scripts and deploy of
special TrustFence artifacts.
- Adds u-boot-dtb.xxx to UBOOT_CONFIG, required for new U-Boots.
- Adds CC8X scripts.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-5936
A mechanism was introduced in U-Boot to dynamically locate the environment
copies within a NAND partition, skipping bad blocks and making full use of
the partition blocks.
To trigger this mechanism in Linux tools (fw_printenv/fw_setenv) the
configuration file /etc/fw_env.config must have both copies entries
pointing to the same offset.
This commit substitutes the hardcoded configuration file for CC6UL with a
stub and generates one on an RPM post-script basing on:
- Supplied DEY variables (with default values per platform):
- UBOOT_ENV_OFFSET: starting offset of the environment within the
partition.
- UBOOT_ENV_SIZE: size of each copy of the environment.
- UBOOT_ENV_RANGE: size in the partition that the environment copies may
occupy, starting from UBOOT_ENV_OFFSET. If undefined, the whole
partition is used.
- Calculated values:
- NAND Erase block size
- Number of blocks available for the environment copies
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-4256
Add support to build U-Boot for variants with 1GB DDR3.
Add support in U-Boot install firmware script to select the
U-Boot artifact to use basing on variant.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-3970
This allows to override the console using the local.conf.
https://jira.digi.com/browse/DEL-2856
Signed-off-by: Diaz de Grenu, Jose <Jose.DiazdeGrenu@digi.com>
- Added the new image type 'recovery.vfat' to the DEY images
generation process. This new image is a clone of the 'boot.vfat'
but including the recovery ramdisk and the recovery boot script.
- Added the new image type 'recovery.ubifs' to the DEY images
generation process. This new image is similar to the 'boot.ubifs'
but including the recovery ramdisk and the recovery boot script.
Signed-off-by: David Escalona <david.escalona@digi.com>
This device tree file corresponds to StarterBoard with ID=129
which corresponds to smart part number CC-WMX6UL-START.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The size of the destination partition (linux) is around 14MiB so the
max-leb-cnt must be reduced compared to the one used for the rootfs
partition.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-2697
- boot.txt
Sets the device tree filename basing on the SOM variant read from
the HWID and boots from NAND.
- install_linux_fw_sd
Deploys a full system (as generated by Digi Embedded Yocto) from
a FAT formatted micro SD card into the NAND flash.
The u-boot-dey recipe is now fully shared by ccimx6 and ccimx6ul platforms
so we can remove the platform-specific appends.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The CC6UL does not support booting from SD card, so it does not make
sense to create a SDCARD image by default.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Mike Engel
Alex Gonzalez
Hector Palacios
Diaz de Grenu, Jose
David Escalona
Isaac Hermida
Javier Viguera