The power regulator connected to the qca6554 chip is always on, which causes
the Bluetooth part to not work correctly after a software-reset.
This commit asserts momentarily the BT_EN line during the start-up sequence
to reset the Bluetooth controller so that it is in a predictable state after a
reset.
https://jira.digi.com/browse/DEL-2623
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
This function is deprecated in favor of bb.utils.contains. The same
change has been done in other layers.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
https://jira.digi.com/browse/DEL-2603
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Jose Diaz de Grenu de Pedro <Jose.DiazdeGrenudePedro@digi.com>
The steps to set the bluetooth MAC address is send an specific hci command
and an hci reset, so the bluetooth interface need to be up in order to
configure it.
Additionally we have generalized the way to read the MAC address from the
device tree and removed some old code for getting the MAC address in
kernel version 2.
https://jira.digi.com/browse/DUB-595
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
Add a software workaround to disable the HW flow control because the SOM
revision 3 (and older) has swapped the bluetooth TX and RX lines so we need
to operate in DTE mode which implies that the HW control lines are swapped.
This also implies reducing the baudrate to avoid the need for HW flow control.
https://jira.digi.com/browse/DEL-2611
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
Implement the set of TRUSTFENCE_ macros to configure each secure boot feature
available in U-Boot.
https://jira.digi.com/browse/DUB-570
Signed-off-by: Jose Diaz de Grenu de Pedro <Jose.DiazdeGrenudePedro@digi.com>
sysinfo is a bash script which gathers all the relevant information
from a running system on a timestamped compressed file.
https://jira.digi.com/browse/DEL-2447
Signed-off-by: Victor Rubio Victor.RubioTorroba@digi.com
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This commit adds a trustfence class to encapsulate all trustfence
configurations.
https://jira.digi.com/browse/DEL-2257
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
This support comes from meta-linaro @9f899282caa9 and adds the ability
to configure getty dynamically from the console argument in the kernel
command line.
This will make it possible to enable/disable the console dynamically as
signalled by U-Boot.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Port the bluez5 qca6564 support based on 5.19 to the current version 5.33.
The ported version is based on qualcomm tag r110048.3.
https://jira.digi.com/browse/DEL-2581
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
This daemon (rngd) feeds random data from hardware device to kernel
entropy pool.
https://jira.digi.com/browse/DEL-2501
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
As of Yocto 2.0, the cryptodev module used as interface between
user-space and hardware encryption is the version 1.7.
According to that cryptodev's version documentation, the cryptodev
engine in openssh is outdated:
https://github.com/cryptodev-linux/cryptodev-linux/blob/cryptodev-linux-1.7/README
They provide an URL with two patches to update openssl. This commit
forward port those patches to the Openssl version used in this version
of Yocto.
https://jira.digi.com/browse/DEL-2501
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
COMPATIBLE_MACHINE is a regular expression, so we need to update the current
pattern for ccimx6 due to it will also match with ccimx6ul.
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
That restriction does not make any difference in the final image
contents, because no package depending on X11 is added to the image, and
it prevents the image from being built with the default DEY
configuration (that has X11 distro feature enabled).
This also allows to build the image in the buildserver with the same job
that builds other X11 based images.
https://jira.digi.com/browse/DEL-2106
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Use LAYERDEPENDS to configure the layer dependences for meta-digi-arm
and meta-digi-dey.
https://jira.digi.com/browse/DEL-1129
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Otherwise building the demo application fails with:
| DEBUG: Executing shell function do_configure
| Project ERROR: Unknown module(s) in QT: svg
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This patch adds a udev rule and a script to detect HDMI hotplug and create
the HDMI audio pulseaudio sink if needed (that is, if the system was
booted with no HDMI cable plugged).
https://jira.digi.com/browse/DEL-2327
Signed-off-by: Jose Diaz de Grenu de Pedro <Jose.DiazdeGrenudePedro@digi.com>
A patch sent upstream has been finally merged so this commit is not
needed anymore.
This reverts commit 6a66656161.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
module-udev-detect blocks the sound interface on boot for about five
seconds while detecting the hardware. This patch removes it so that
module-detect is used instead, which uses static hardware detection and is
faster.
https://jira.digi.com/browse/DEL-2218
Signed-off-by: Jose Diaz de Grenu de Pedro <Jose.DiazdeGrenudePedro@digi.com>
Move this variable to DEY distro conf so that it is available for any
recipe built with the distro.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-2192
There is another OpenGL demo application QT5 Hello Windows for testing
purposes.
https://jira.digi.com/browse/DEL-2184
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
It has been observed that the wireless interface ocassionally fails to resume
from suspend on extensive long run validation testing, so we workaround it by
bringing the interface down before suspend and bring it up again after resume
This reverts commit a77cd1406d.
https://jira.digi.com/browse/DEL-2217
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
This image provides a demo rootfs with QT. It can be built for
framebuffer and also for X11.
https://jira.digi.com/browse/DEL-2196
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
We were masking meta-fsl-arm linux recipes to clean some warnings on
bitbake parsing. This does not happen anymore with new versions of
Yocto, so just remove this BBMASK.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This install the 'obexd' server which is needed for the QT5 bluetooth
file transfer example applications.
https://jira.digi.com/browse/DEL-2147
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Generalize bluetooth support so it can be used not only with bluez4 but
with bluez5 as well. Use EXTRA_QMAKEVARS_PRE to pass the packageconfig
options to the do_configure task.
https://jira.digi.com/browse/DEL-2147
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This is a user-space workaround for the reboot/poweroff problems we
are having in the ccimx6sbc. Seems that they are not reproducible when
only one core is enabled, so the workaround is to disable the rest of
the cores for rebooting/halting.
https://jira.digi.com/browse/DEL-2133https://jira.digi.com/browse/DEL-2148
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
(cherry picked from commit a9e36a74bb20ab38f220116ba2742dca3d80c293)
Also initialize the video sink to 'glimagesink' in case it has not been
configured from the environment, but only for the X11 application
(gtk-play). This recipe also provides a command line application for
framebuffer (gst-play) that is not affected by this change.
https://jira.digi.com/browse/DEL-2132
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
The example applications are not packaged by default, so extend the
recipe to create a package with the example applications.
https://jira.digi.com/browse/DEL-1960
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
The script toggles the BT power GPIO regardless of the value being
undefined.
Check that the GPIO is defined before trying to toggle it.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The BT power GPIOgpio was determined basing on machine name on device tree.
This corresponds to the name of the board, and might be changed by a user
that designs his own carrier board to use the module on.
Besides, the BT power GPIO is a pin that's routed on the module (both on
the ConnectCore 6 and on the ConnectCard for i.MX28) not on the carrier
board.
This commit determines the BT power GPIO basing on the module string inside
the 'compatible' property. This must exactly match the module name and is
a required property for using Digi module's BSP.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-2109
So we can build a 'dey-image-graphical' image for framebuffer with
support for QT5.
https://jira.digi.com/browse/DEL-2017
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
No functional change, as 'package-management' is added via the included
dey-image-minimal recipe, and 'pointercal-xinput' is a dependence of
xinput-calibrator which is added for X11 images.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
By default QT5 applications use 'xcb' platform plugin but this can be
changed using the QT_QPA_PLATFORM environment variable. On non-X11
images the 'xcb' platform plugin obviously does not work, so just
configure 'eglfs' for non-X11 images.
https://jira.digi.com/browse/DEL-2017
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
There are some demo apps that otherwise fail with:
QSqlDatabase: QSQLITE driver not loaded
QSqlDatabase: available drivers:
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Isaac Hermida
Javier Viguera
Jose Diaz de Grenu de Pedro
Alex Gonzalez
Victor Rubio
Arturo Buzarra
Hector Palacios