We can't run a post installation script in a readonly file system.
We need to provide a configuration file beforehand.
https://onedigi.atlassian.net/browse/DEL-8556
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
We no longer need logic to determine the SOM's RAM size and bus width, we only
need to know the SOC revision, which is info that is always available.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Now that both U-Boot and the SCFW can autodetect the RAM configuration, we can
simplify the imx-boot build process to generate two binaries (one per SOC
revision) instead of eight. Build "flash_spl" imx-boot images and use only one
global defconfig for u-boot.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This update includes automatic RAM configuration detection, and only one SCFW
binary is needed for all ccimx8x variants. Adapt the imx-boot recipe
accordingly.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
For the ccimx8x, we changed the order of the steps in do_deploy() from:
Deploy -> Rename files -> Move binaries
To:
Deploy -> Move binaries -> Rename files
When it's time to rename the files, they won't be in their original place and
the process will fail. Make sure we move the files after they've been renamed
to avoid errors.
Also, one move operation is enough for all artifacts, so remove the second
operation.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
There are two different firmware files for Bluetooth on Murata's type2AE
module:
- JRL: It configures a Bluetooth TxPower of 7dB, to be used in Japan
only.
- FCC.CE: It configures a Bluetooth TxPower of 5dB, to be used in the
rest of the world.
To comply with the FCC requirement that it should not be possible to
configure different regulatory domains, or in this case configurations,
than FCC, only deploy the FCC.CE file by default:
- BCM4373A0_FCC.CE.hcd (md5sum: 1e287a3ab7f83e59352cb321315ea80f)
This file reports the following information during boot time:
Bluetooth: hci0: 89373 UART 37.4 MHz wlbga_BU sLNA muRata Type 2EA 5dBm 20220608-0103
Bluetooth: hci0: BCM4373A0 (001.001.025) build 0155
JRL file will be added via the Worldwide DEY patch addon that customers
can request from Digi.
https://onedigi.atlassian.net/browse/DEL-8453
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Replace the CLM blob file from Github, which supports several countries
with a custom US-only CLM blob file. This way, default images will only
have support for US regulatory domain, therefore complying with FCC
requirements.
The Worldwide CLM blob file will be provided by Digi International on
request.
https://onedigi.atlassian.net/browse/DEL-8453
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
We can't run a post installation script in a readonly file system.
We need to provide a configuration file beforehand.
https://onedigi.atlassian.net/browse/DEL-8556
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
This commit modifies the boot script condition to apply the overlay for MCA
based on HWID MCA field.
https://onedigi.atlassian.net/browse/DEL-8521
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The tools STM32MP_KeyGen_CLI and STM32MP_SigningTool_CLI have
a dependency of libQt5Core.so.5 which is provided by qtbase.
Add this dependency to avoid errors during SDK generation.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
For the moment, do not sign aditional artifacts, such as the ramdisk,
the kernel or the boot scripts for STM platforms.
In the specific case of the ramdisk, simply copy it over with the
expected filename extension.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The do_deploy:append did three things:
- adapt the U-Boot filenames to 'u-boot-<platform>-<config>.<ext>'
- sign/encrypt the U-Boot files (only for iMX6 family)
- sign the boot scripts
Convert the first two actions into functions (the third already was) and
call them conditionally as postfuncs.
Also skip the signing of U-Boot files if the platform is not based on
iMX6 family.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Certain platforms share a processor family but need to be differentiated
between them. DEY was using the variable DIGI_FAMILY as the SOM name
rather than the family. It becomes useful to have both (DIGI_SOM as the
more specific, and DIGI_FAMILY as the more generic).
This is the case, for example, of:
- ccmp1 (family)
- ccmp15 (SOM)
- ccmp13 (SOM)
- ccimx8m (family)
- ccimx8mm (SOM)
- ccimx8mn (SOM)
Both variables are used on the machine overrides.
Where DIGI_FAMILY was used, use now DIGI_SOM.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
This recipe downloads a tarball that contains the binaries:
- STM32MP_KeyGen_CLI
- STM32MP_SigningTool_CLI
from ST Microelectronics STM32CubeProgrammer v2.12.0.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The name of the variable was not very intuitive of what
it contains. This variable expands to the SoC vendor
(NXP or STM).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Commit 065cf3e9 ("kirkstone migration: general update to the new override
syntax") incorrectly renamed binaries in a massive change. This commit restores
the binary names to the original.
https://onedigi.atlassian.net/browse/DEL-8478
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
These are recipes we created to support Google Coral on i.MX platforms. ST's
machine learning layer provides similar recipes, so to avoid conflicts, move
the recipes meant for i.MX platforms to a dynamic layer.
https://onedigi.atlassian.net/browse/DEL-8308
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The HWID is populated on the device tree by the boot loader.
This can be used as a key modifier when encrypting the U-Boot
environment. Some old U-Boot versions however, did not populate
the HWID on the device tree. When updating firmware from an
old version to a new one, the library may not be able to read
the HWID from the DT and then be unable to unencrypt the
environment.
This patch implements a fall-back function to read the HWID
directly from the nvmem node (sysfs). Implementation has been
done for ccimx6 family only, where this case of old U-Boot
can happen.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-8444
(cherry picked from commit 222a91f213)
The HWID is populated on the device tree by the boot loader.
This can be used as a key modifier when encrypting the U-Boot
environment. Some old U-Boot versions however, did not populate
the HWID on the device tree. When updating firmware from an
old version to a new one, the library may not be able to read
the HWID from the DT and then be unable to unencrypt the
environment.
This patch implements a fall-back function to read the HWID
directly from the nvmem node (sysfs). Implementation has been
done for ccimx6 family only, where this case of old U-Boot
can happen.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-8444
This commit modifies the boot script condition to apply the overlay for DVK v1
on boards without the board_version variable defined.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit adds an overlay for DVK v1 and modifies the boot script to apply it
based on the board_version variable.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Partitions 'fip-a' and 'fip-b' are redundant at the moment. They are
not currently part of the dualboot system. In consequence, program
both partitons unconditionally during the install process.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
This commit updates the required firmware binaries for Bluetooth and Wireless
interfaces, based on the Murata release imx-kirkstone-fafnir_r1.0 that matches
with the Cypress Linux WiFi Driver (FMAC) release v5.15.58-2023_0222 (Wireless
firmware v13.10.246.300)
https://onedigi.atlassian.net/browse/DEL-8407
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
True is the default since long time ago, and thus not necessary. This
follows similar changes done in other layers.
Command used:
sed -e 's|\(d\.getVar \?\)( \?\([^,()]*\), \?True)|\1(\2)|g' -i $(git grep -E 'getVar ?\( ?([^,()]*), ?True\)' | cut -d':' -f1 | sort -u)
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Set parameter 'greentxConfig__0_0=0x2' to use the optimal TxPower
in MCS7 data rates, improving performance.
Also, adjust maximum TxPower in the 5GHz band to account for
output power tolerances.
The new BDF is:
- bdwlan30_US.bin (53072f8af541a49e4ed9c22698b1912f)
https://onedigi.atlassian.net/browse/CC6UL-1302https://onedigi.atlassian.net/browse/DEL-8364
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Number of bootup logos is now configured using fbcon=logo-count parameter,
so use it instead of our deprecated custom code in the kernel.
For backwards compatibility, we add this parameter in the u-boot boot
script for all platforms but the ccimx93, where this is directly handled
by u-boot (v2022.04).
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This reverts commit 2bdfdc92e1.
This suffix was removed on error. The artifact does have the suffix.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
This variable was removed from meta-st-stm32mp so we need to get rid of it
in meta-digi, too.
Reported-by: Javier Viguera <javier.viguera@digi.com>
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-8268
Rework the "build_uboot_scripts" to prevent changing the templates in
the WORKDIR, as those are part of the SRC_URI. Instead, change the
deployed scripts by using "sed" and redirection.
Also, removed UBOOT_HAS_FASTBOOT altogether, as there is no platform
that does not support fastboot.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Instead of overriding the whole do_compile function, just to reconfigure
u-boot for Trustfence, create a do_configure pre-function that takes care
of that. This allows the removal of duplicated code.
Also, disable the generation of u-boot environment artifacts. We are
not using them and so many u-boot artifacts in the deploy directory
are confusing.
Finally, adjust the names of the TF u-boot artifacts in the do_deploy
append function.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
These are just a verbatim copy of the ccimx8mm ones, so the project is
buildable. This file list should be revisited and adapted for the
ccimx93.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Add configuration 'BUILD_UBOOT_SCRIPTS' to select whether to build the
boot and install scripts or not, and set it to 'true' by default.
This allows removing the scripts on upper Yocto layers.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
All the dualboot logic will be checked in run time.
To do this:
* Include the altboot.src by default in all the images
* Create a post installation script to change the
firmware_download_path in the cloud connector
* Unify the swupdate file descriptor for dual and single boot
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
Increase the timeout from 90 to 120s since it's a large image
and it may take more time on different NANDs.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The U-Boot environment resides on a UBI volume. The uuu script
relies on the environment to save part of the commands that
U-Boot needs to execute after reboot in the middle of the
installation. If the UBI volume 'uboot_config' does not exist
the installer fails.
This commit:
- Creates a function -on the uuu script only- for obtaining
the result of running any U-Boot command (0=success, 1=error).
- Checks the existance of 'uboot_config' volume.
- Runs 'ubivolscript' script to create the UBI volumes layout
that generates the environment volume if it doesn't exist.
- Increases the timeout for running the 'ubivolscript' since
there are occasions in which 'ubi part' (which is part of the
script) takes more time (if it cannot find the fastmap).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
By default ccmp1 platforms have dualboot mode by default, however the required
boot script was added to ccmp15 platform only, so this commit fixes it.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The first time the 'dualboot' variable is tested it is directly run in
the script and doesn't need to escape the special characters.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
When Dual Boot is not enabled, 'rootfsvol' variable must point to the
single boot system rootfs partition 'rootfs'.
Explicitly set this value. Otherwise the script relays on the default
rootfsvol value, which may be a Dual Boot partition.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
- create dualboot.bbclass that
- sets DUALBOOT_ENABLED variable
- defines partition names and function for changing the sw-description
for swupdate
- move files from layer into meta-digi
https://onedigi.atlassian.net/browse/DEL-7962
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
On the CCMP1 SOMs, we only consider a single system partition called UBI,
with many UBI volumes.
The variable 'singlemtdsys' allowed to change between this and
a system with multiple MTD partitions with one UBI volume each
(old approach on CC6UL).
This commit removes the variable and uses the logic as if it was set.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Use the latest 2AE NVRAM file from the master branch. This file improves
the EVM performance for the 2AE murata module.
MD5SUM:
- cyfmac4373-sdio.2AE.txt: 6301804650847946c79797387eda9c7a
https://onedigi.atlassian.net/browse/DEL-7936
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
This commit adds Bluetooth Vulnerability CVE-2019-9506
resolution to the firmware file.
CVE-2019-9506 is a Bluetooth key negotiation vulnerability.
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
https://onedigi.atlassian.net/browse/DEL-7134
Co-authored-by: Javier Viguera <javier.viguera@digi.com>
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Reset the FW files to release r00006.3.470144.2a
Verbatim copy of the recipes in DEY-3.2, using command:
git restore -s dey-3.2/master -- meta-digi-arm/recipes-bsp/firmware-qualcomm
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
For the CC6UL 1GB flash variant, the programming of the rootfs exceeds
the current 90 secs timeout, giving following failure:
[Bulk(R):LIBUSB_ERROR_TIMEOUT] fb[-t 90000]: ucmd update rootfs ram ${fastboot_buffer} ${fastboot_bytes} -e
Error: Bulk(R):LIBUSB_ERROR_TIMEOUT
Increase the timeout to prevent the failure.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
As that's an old VM with limited specs, there is no much gain on using
it over the canonical Stash repositories that justifies the code
overhead and the possible errors due to synchronization problems.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This commit updates the required firmware binaries for bluetooth and wireless
interfaces, based on the release imx-hardknott-drogon_r1.0 (Wireless firmware
v13.10.246.265)
https://onedigi.atlassian.net/browse/DEL-8021
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The recipe fails to build for the target, but that is expected, as this
is a tool you need to run in the host or from the toolchain/SDK, so
rework the recipes to restrict only for native and nativesdk.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Yocto 4.0 only supports OpenSSL 3.0.x while NXP's CST (code signing
tool) is still using OpenSSL 1.1.x. So the build fails when using the
Yocto-build OpenSSL. Instead, build OpenSSL 1.1.1 as part of the build of
the CST and link statically against libcrypto, so the resulting binaries
(cst, srktool) do not depend on any specific OpenSSL version installed
on the development computer.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
In order to perform the standalone signature process, it was required
to rebuild the Toolchain with Trustfence support enabled.
CST source code is now available for downloading in the Digi FTP, so add
Trustfence sign scripts and cst/srktool to the default toolchain for it
to be used for standalone signature without rebuilding.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
(cherry picked from commit 2c9b721fb9ce38dcd0034e22d95db6e0ee068955)
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
(cherry picked from commit 16eded4f0edcc603de83be7155f7c09718ba5ddd)
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This commit updates the wireless firmware in order to work with the new Linux
qcacld-3.0 wireless driver.
Latest release "r10016.1 - Post-CS3 1.0.016.1" updates the following files from
"qca6574au-le-2-2-1_qca_oem" product branch:
PCIe:
- athwlan.bin (b4fd36922625b7303d006581f6c7cd10)
- utf.bin (0d70048214fea05d1c40b3034e8107cd)
SDIO:
- qwlan30.bin (342cb50ce5c6ff930a65f341c0dfbc77)
- utf30.bin (f94810be89cc2f3e979ab4a57243872b)
https://onedigi.atlassian.net/browse/DEL-7916
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This recipe will download and install the required firmware binaries for
bluetooth and wireless interfaces. This recipe is based on the release
imx-hardknott-cynder_r1.0 (Wireless firmware v13.10.246.261)
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit adds u-boot build support for the CCMP15 platform.
The installation scripts are copies from the CC6UL platform.
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
https://onedigi.atlassian.net/browse/DEL-7797
The sign mode needed for each platform is invariable, and since the platform
is already a mandatory parameter for the script, we can store this information
implicitly. Reflect this change in every recipe where the script is used, but
keep the variable at the Yocto level since it's still needed in several places.
https://onedigi.atlassian.net/browse/DEL-7862
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit updates the US Board Data File (BDF) to include the changes
required to pass the EN 300 328 V2.2.2 blocking test.
The new BDF files are:
- ccimx6/bdwlan30_US.bin (eb3d3cdafd30b30e837974177a281648)
- ccimx8m/bdwlan30_US.bin (72531e6e0870673e4ba2b02bd551925b)
- ccimx8x/bdwlan30_US.bin (1cf667271da33f6eb207360eeb3d4d63)
https://onedigi.atlassian.net/browse/DEL-7773
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This makes it possible to distinguish between two different packages:
* NXP's tensorflow-lite, which contains modifications for i.MX platforms
* Our tensorflow-lite, which is meant to be used with Google Coral
Since tensorflow-lite-coral provides a subset of the files provided by
tensorflow-lite (specifically, the python libraries), make the packages
conflict during runtime.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This is a small oversight on NXP's part, because this package is pulled in as a
dependency of imx-vpuwrap, but it's only compatible with their EVK board,
making the build fail on any other i.MX8MP board.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
These variables were originally set in NXP's recipes, but they moved their
definitions to each platform's configuration file. Set the appropriate values
where needed. While at it, replace every mention of the SOC_TARGET variable
with its new name, IMX_BOOT_SOC_TARGET.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
NXP now uses the meta-freescale version of the imx-boot recipe as a base, and
applies a .bbappend in meta-imx to apply more customizations. Reflect this
in meta-digi-arm and merge said .bbappend with ours. While at it, omit one of
NXP's operations in their do_deploy, since it breaks our build and doesn't look
essential.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This recipe is only compatible with the i.MX8MP EVK, so it might be
platform-specific or board-specific. Add it for now to be safe.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This recipe was missing from our layer, so add it just in case it's needed
by any new package.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Update the recipes to v8.14. NXP changed the mechanism used to load the sdma
and regulatory firmware (they now use firmwared), so remove our ccimx8mm sdma
fw service for now and see if we need a similar workaround with the new
mechanism.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Digi Embedded Yocto 3.2-r2.2
Manually changed recipes to use the master branches instead of the fixed SHA1
from the last release.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
U-Boot uses partition names instead of partition indexes for the nand devices.
This commit syncs the boot scripts with the new dualboot variables.
https://onedigi.atlassian.net/browse/CC6UL-1254
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Create this symbolics links in build time instead of doing it
in run-time. This simplifies the system and allows it to work
with read only filesystems.
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
Before this patch the MAC addresses were read from the device
tree in the qualcomm.sh script executed at init, and a creates
a file where the MAC where located.
In 0a92f5d9e8df644de74e74f152ed6ff3dd8d3369 in the qca driver
the support to read these MAC addresses from the filesystem
was added.
This commits creates the simbolic link between the device tree
and the expected path where the MAC addresses where located, and
gets rid of the file with the MAC addresses.
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
mkimage logs are required for signature on CC8X and CC8M platforms. Create a
copy in the 'imx-boot-tools' deploy directory so a prebuilt imx-boot file can
be later signed using the standalone signature procedure.
Build the 'print_fit_hab' target unconditionally so the log is available for
future standalone signature processes.
Also, use 'CONFIG_MKIMAGE_LOG_PATH' and 'CONFIG_FIT_HAB_LOG_PATH' variables to
point to the logs before calling the sign scripts. We no longer require
creating a symbolic link of the log files.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Add missing call to 'uuu' and erase the partition before creating
the UBI volumes.
Also add larger timeouts to erase operations.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The config file /etc/fw_env.config is generated dynamically basing on
the partition table and, in the case of NAND-based SOMs, on the NAND
geometry. This is done on a postinst script that modifies the file on the
first boot of the target. Since this is not allowed on read-only-rootfs,
this commit adds a default fw_env.config file to use instead when
read-only-rootfs is enabled.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-7708
This allows the packages to be included in the ccimx6sbc images. While at it,
include the Qualcomm bluez patches in ccimx6 builds. These patches aren't
destructive, they simply add functionality required by the Qualcomm chip, so
they shouldn't have any secondary effects when using the Atheros chip.
https://onedigi.atlassian.net/browse/DEL-7661https://onedigi.atlassian.net/browse/DEL-7666
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The variable 'dualboot' (and 'singlemtdsys' for CC6UL) was restored
after the bootcmd that runs the first time after programming U-Boot runs
fastboot again to resume the script.
This is ok for the CC6UL but not for the rest of platforms, that run the
partition script on the bootcmd, *before* running fastboot.
Restore the variables for all platforms in the bootcmd right after
resetting the environment.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
U-Boot has embedded support to handle bootcount tries.
When the limit of tries is reached, U-Boot runs the script
in `altbootcmd` rather than the usual `bootcmd`.
This other script resides on meta-digi-dualboot layer.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
Ensure stdout redirection to the USB interface is removed in every case.
Otherwise, it would be left redirected when INSTALL_UBOOT_FILENAME is
manually set.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Install scripts may rework the partition table basing on the value of
env variables. Information of UBI volumes may remain on the NAND that
could later not correspond to the new partition table.
Make sure the MTD partitions are erased prior to updating:
- For Multi-MTD, append '-e' option to the update command.
- For Single-MTD, erase the system partition.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Check the status of 'dualboot' env variable.
If set to "yes", use the dualboot partition table in the script and
restore the variable (default is "no") after resetting the environment.
Also, for dualboot, there's no need to wipe the recovery partition or
boot into recovery mode.
For dualboot, this script programs both systems A and B with the same
images.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-7649
Commit c33fc8a7fe wrongly used
https protocol when using MTK remote when it should have been
ssh.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
When we added the SDMA fw systemd service, we accidentally made it so that all
scripts were installed only when using systemd. These files are still needed
when using sysvinit, so correct this change.
While at it, include the SDMA fw service in firmware-imx-sdma's FILES.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
When DualBoot mechanism is enabled and an update is pending,
the boot script needs to change certain variables and save the
environment.
The regular boot script already changes a number of variables,
such as 'extra_bootargs' and 'overlays' by appending strings to
the already existing values. Saving the envionment may make these
grow endlessly with each iteration of the boot script.
For this reason, move the DualBoot check as the first thing in
the script, save the environment if needed, and then continue
with the normal flow, that changes variables before booting
but doesn't save them.
On certain scripts, this allows us to get rid of some instructions
for resetting the overlays variable.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The script required the passing of option '-b' for setting up the
target to use a single MTD partition and multiple UBI volumes.
If a target however already has the variable 'ubisysvols' set to
'yes' but this parameter is forgotten when calling the script, the
partition layout would change to default (several MTD partitions).
Remove the recently added '-b' option and make the script decide
basing on the current value of 'ubisysvols' variable.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The script preserves the current value of env variable 'ubisysvols'
so that the new partition script generates the appropriate partition
table before proceeding with the update operations.
If using a UBI volumes layout, the script will not erase the partitions.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-7614
With U-Boot supporting the creation of mtdparts and UBI volumes depending
on the value of variable 'ubisysvols', adapt the install script to make
use of those to generate a partition table and UBI volumes accordingly.
This can be triggered with new option '-b'.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Set the new variable 'rootfsvol' to rootfs_a or rootfs_b when dualboot is
enabled, to cover the case where the devices uses the 'system' partition
with different UBI volumes.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The support for dualboot was integrated on meta-digi-dualboot layer, but it
really depends only on environment variable 'dualboot' so we'd better
integrate the support on the scripts in meta-digi, to avoid synchonization
problems between both layers.
This also allows to be able to easily enable dualboot in U-Boot with the
variable, without needing to update the script on the linux partition.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Enabling DIGI_INTERNAL_GIT defaults to LOG server. The build from local
MTK Digi server was broken.
Fix uboot and linux recipes declaring different repo paths depending on
whether the local remote is LOG or MTK.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
When we added the SDMA fw systemd service, we accidentally made it so that all
scripts were installed only when using systemd. These files are still needed
when using sysvinit, so correct this change.
While at it, include the SDMA fw service in firmware-imx-sdma's FILES.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This command was already present on the script used for CC8X. Add it here
so the scripts are as much alike as possible.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Fastboot is configured on boot with the current MMC configuration.
If we create a GPT partition table, we need to restart fastboot before we
try to program any partition with the 'flash' fastboot command.
Set 'fastboot_dev' to a different device, 'sata' for example an back to 'mmc'
to trigger a fastboot restart after creating the partition table on blank
devices.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
The current syntax only works properly when running the script through bash.
Change this so that it works for other shells as well.
While at it, fix a typo in the message that appears when the variant can't be
detected in the 6UL script.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
We document how to use this script from the Yocto image directory. Now that the
*.ext4 files are compressed by default, the script needs to automatically
decompress said files before starting the update process.
https://onedigi.atlassian.net/browse/DEL-7582
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit adds the Edge TPU simple camera examples to exercise the Google
Coral devices with Digi Embedded Yocto.
https://onedigi.atlassian.net/browse/DEL-7547
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit adds the required libraries and packages to exercise the Google
Coral devices with Digi Embedded Yocto.
https://onedigi.atlassian.net/browse/DEL-7547
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The install script of cc8x had errors (using double '==' instead
of single on comparisions).
Besides fixing this typo, this commit changes the logic to:
- default to 2GB U-Boot for variants other than the ones in the
list.
- consider variant code 0x00 (not programmed HWID) as a failure.
thus forcing the user to specify the file on the command line.
This second action is done also on the cc6ul script.
Reported-by: Hector Bujanda <hector.bujanda@digi.com>
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Update US Board Data File to include the changes required to pass the
EN 300 328 V2.2.2 blocking test.
The new BDF is:
- bdwlan30_US.bin (24140b5c28256cadfd95bc28fc574733)
https://onedigi.atlassian.net/browse/DEL-7576
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
install_abort is a temp variable so 'test -n' doesn't work on it.
This was fixed in all scripts except the USB script of ccimx6sbc.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
- Check the existence of files before the 10 second wait.
- Print the list of filenames to program to each partition.
- Print the file that's being updated to each partition.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
With the generalization done in previous commits, we have now several files
that are identical and can be merged into a common SOM or SOM family
folder.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Create global variables:
DEFAULT_IMAGE_NAME
GRAPHICAL_IMAGES
to have them substituted on the U-Boot install scripts for better
generalization.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
U-Boot install scripts (from uSD and USB) were hard-coded to dey-image-qt.
Allow to install other image files by setting a new variable 'image-name'
which defaults to 'dey-image-qt' if not defined, except for the CC6UL
SBC Express, that defaults to 'core-image-base'.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7385https://jira.digi.com/browse/DEL-7333
On these boot scripts, this variable is not used, so we can remove it.
Besides, it's generated by U-Boot code.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Use ##MACHINE## placeholder to have it later substituted by the recipe
using Yocto ${MACHINE} variable.
This will help later reducing the number of files to have one per SOM
(or even family) instead of one per platform.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Otherwise, the name of the file will be "u-boot-dey-initial-env", causing
errors when reading the default environment from userspace, since libubootenv
expects "u-boot-initial-env" instead.
https://onedigi.atlassian.net/browse/DEL-7566
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit adds the sdma-firmware.service to the rootfs
to load the SDMA firmware during boot, that is necessary
for some drivers to work correctly.
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
Non-graphical images (core-image-base, dey-image-aws) don't contain the
graphic-backend on their filenames.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
- Determine first the filenames and abort if any does not exist.
- Print a warning message about the erasing of the media with a list
of partitions and files to use for the update
- Sync the different scripts so they look more similar
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7333
Similar to how it's done on the ccimx6ul, create a function for updating
a partition with a file, that also prints a message.
Rename the function to be the same in all scripts.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7333
Previously, this script only allowed the U-Boot filename as parameter.
This commit makes use of getopts() to pass the following options to the
script:
-h, for help
-i, to pass the dey image name that prefixes the firmware filenames
-n, to skip the 10 seconds delay that allow you to cancel the process
-u, to pass the U-Boot filename
The default image name (if none passed) keeps being 'dey-image-qt' but the
new option allows reusing this script to install dey-image-webkit or
dey-image-aws images.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7385
The prebuilt 'athtestcmd' binary allows you to test tx/rx of the
Wi-Fi MAC, when the driver is loaded in test mode.
This is required for certifying Wi-Fi in products, so add it by
default for the ccimx6sbc.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7444
(cherry picked from commit acb402fdcfa54d8d5519580ff7fcfb76fbed3f49)
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Since this feature was introduced in newer versions of U-Boot, we need
to disable it for v2017.03 to avoid several compilation issues.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Update US Board Data File to use the new GOLDEN2 calibration.
The new BDF is:
- bdwlan30_US.bin (328f970444b5eaaa48c0188cea1685e3)
https://jira.digi.com/browse/CC6UL-1210
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
(cherry picked from commit 373b3958bad9d0c462349d89ef5832e843624b01)
This commit fixes the following warning:
WARNING: meta-digi/meta-digi-arm/recipes-bsp/trustfence-cst/trustfence-cst_3.3.1.bb:
Recipe trustfence-cst sets S variable with trailing slash '/tmp/work/aarch64-dey-linux/trustfence-cst/3.3.1-r0/cst-3.3.1/',
remove it
https://jira.digi.com/browse/DEL-7508
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This default environment is needed by packages like libubootenv.
https://jira.digi.com/browse/DEL-7508
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This package has been entirely replaced with libubootenv
https://jira.digi.com/browse/DEL-7410
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This is a replacement for u-boot-fw-utils. Adapt the u-boot-fw-utils patches
to this new library and include the same logic as the u-boot-fw-utils recipe
(generate and install the U-Boot environment configuration file in the rootfs)
For now, remove the u-boot-default-env dependency, since the package doesn't
exist in zeus.
https://jira.digi.com/browse/DEL-7410
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The new SCFW re-enables "Read DBI deskew configuration"
setting, to support Nanya LPDDR4 chips.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/CC8X-297
Add a patch series to customize the ATF console for the ConnectCore 8M platforms,
and to disable the Cortex-M debug UART.
https://jira.digi.com/browse/DEL-7497
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Update file:
- bdwlan30_US.bin (93a58f0f8e241bef6600d53d013c3cb2)
This file was generated by calibrating several v3 CC8MN SOMs and
merging their resulting BDF files into a new Golden file.
Target output powers tables and CTL tables remain intact.
Reference calibration file is obtained from 'qca6574au-le-2-2-2_qca_oem' repo
at tag 'r00005.1' under path
'wlanfw/cnss_proc/wlan/fw/target/sdio_dst/qc6174/bdwlan30.bin':
- bdwlan30.bin (8a40d95698825e1718bee640b1f7982a)
Target output powers respect the maximum EVM for every data rate.
CTL limits comply with FCC, CE and TELEC certifications.
https://jira.digi.com/browse/DEL-7487
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
(cherry picked from commit cceffef831edd10b017aac3006636c98f7baa0a9)
Update file:
- bdwlan30_US.bin (93a58f0f8e241bef6600d53d013c3cb2)
This file was generated by calibrating several v3 CC8MN SOMs and
merging their resulting BDF files into a new Golden file.
Target output powers tables and CTL tables remain intact.
Reference calibration file is obtained from 'qca6574au-le-2-2-2_qca_oem' repo
at tag 'r00005.1' under path
'wlanfw/cnss_proc/wlan/fw/target/sdio_dst/qc6174/bdwlan30.bin':
- bdwlan30.bin (8a40d95698825e1718bee640b1f7982a)
Target output powers respect the maximum EVM for every data rate.
CTL limits comply with FCC, CE and TELEC certifications.
https://jira.digi.com/browse/DEL-7487
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
(cherry picked from commit cceffef831edd10b017aac3006636c98f7baa0a9)
There's a Yocto configuration option that enables this feature in U-Boot, but
since imx-boot images are signed using the scripts in trustfence-sign-tools,
said configuration is lost and the scripts don't take it into account if it's
enabled. Make sure that the configuation carries over to the script.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Allow users to select Certified Bluetooth 4.1, rather than
the default not-certified Bluetooth 5, through the use of variable
BT_FW_VERSION="4"
md5sums:
nvm_tlv_3.2.bin ==> 9621f50172f2bfb4f65f8e5c6528b614
rampatch_tlv_3.2.tlv ==> 769e1fc9e5a2061bb3aaa1f32dac3804
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
This overlay added cooling devices for all quad cores.
On the latest BSP, the SoC device tree include contains all four
cooling devices and the newest U-Boot is able to delete the nodes
for non-existing cores, so there's no need for this overlay
anymore.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Otherwise, mkimage will delete the device trees between imx-boot builds,
causing the build to fail when generating a signed imx-boot.
https://jira.digi.com/browse/DEL-7420
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Javier Viguera
Francisco Gil
Gabriel Valcazar
Isaac Hermida
Gonzalo Ruiz
Arturo Buzarra
Hector Palacios
Tatiana Leon
Mike Engel
Hector Bujanda