A corner case requires to save the environment so that the
boot command works after reset.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DUB-681
The default DEY image recipe for ccimx6ulsbc builds dey-image-qt.
The graphical backend is determined dynamically.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
- boot.txt
Sets the device tree filename basing on the SOM variant read from
the HWID and boots from NAND.
- install_linux_fw_sd
Deploys a full system (as generated by Digi Embedded Yocto) from
a FAT formatted micro SD card into the NAND flash.
https://jira.digi.com/browse/DEL-2925
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
- boot.txt
Sets the device tree filename basing on the SOM variant read from
the HWID and boots from NAND.
- install_linux_fw_sd
Deploys a full system (as generated by Digi Embedded Yocto) from
a FAT formatted micro SD card into the NAND flash.
The u-boot-dey recipe is now fully shared by ccimx6 and ccimx6ul platforms
so we can remove the platform-specific appends.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The setting of 'bootcmd' in the script was done using single quotes, which
doesn't expand variables. As a consequence the following variables must
be defined again (during the execution of the second part of the script):
- mmcdev
- INSTALL_LINUX_FILENAME
- INSTALL_ROOTFS_FILENAME
This patch changes the single quotes with double quotes, so that these
variables are expanded during the setting of 'bootcmd' with the values
assigned at the begining of the installation script (notice these are
not dynamically generated so there is no risk to expand them).
At the same time we need to escape with a backslash:
- double quotes containing strings
- variables that we don't want to expand (like the return value $?)
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
- Add semi-colons to instructions inside 'setenv' commands
- Remove semi-colons in instructions where they are not needed (for
consistency with the rest of instructions)
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Old versions of u-boot 'v2013.0x' have a bug in the shell's test command
that makes structures like:
if test "${not-existing}" = "0x01"; then ...
if test -z "${not-existing}"; then ...
to fail when the checked variable does not exist.
So implement workarounds in the updater script to overcome this problem.
This is needed because the script may be used in modules with an old
pre-installed u-boot.
https://jira.digi.com/browse/DEL-2231
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
The install script allows for an easy deployment of the DEY firmware
artifacts into the eMMC of the ConnectCore 6 by using a micro SD card.
The install script:
- updates U-Boot
- resets the U-Boot environmnet to default values
- formats the User Data partition of the eMMC
- installs the firmware images (linux and rootfs partitions)
- resets/starts the system
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-2192
Carrier board version is determined by U-Boot variable $board_id
which will be defined if a board ID has been burned on certain
OTP bits.
Use the value in this variable to create the $fdt_file variable
using the suffix "-id${board_id}" to point to the device tree
file that matches that board ID.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-2160
Hector Palacios
Isaac Hermida
Javier Viguera
Alex Gonzalez