This commit updates the CC6 and CC6QP platform configurations to use the latest
NXP BSP based on Linux kernel v6.6, unifying support across all NXP-based
platforms.
https://onedigi.atlassian.net/browse/DEL-9758
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
On NXP platforms, the signed/encrypted bootloader images are not
included on the installer ZIP. This prevents from using the installer
when TrustFence is enabled.
This commit adds to the installer:
- If encryption is enabled
- encrypted bootloader
- signed bootloader (for USB recovery boot)
- If encryption is disabled
- signed bootloader
- If TrustFence is disabled
- non-signed bootloader
It also treats the ccimx6ul special, as this has a dedicated file for
USB recovery boot.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-9698
IMAGE_FSTYPES was declared on each platform config file, but it has the
same values for all platforms depending on the storage media (mmc or mtd)
and whether read-only is enabled.
Move the conditional weak assignment to digi-default.inc and remove it from
each platform config.
In the case of STM platforms, since IMAGE_FSTYPES is weak-assigned by STM
layer, we still need to append/remove from it inside the platform config,
but move it to the family includes, rather than declaring it on each
specific platform.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The generation of the sdcard image takes time and resources, and
it's not involved in the Get Started.
This can be easily re-enabled by appending the variable in the
project local.conf.
Append the variable in the build scripts, to facilitate its usage
on release builds.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The USB and SD installers are U-Boot scripts that are practically
identical.
Merge them into a single template with a couple of machine variables that
determine the default device index in U-Boot for the USB or the microSD
card.
Do dynamic substitutions to create the two installers out of the template.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
We tested all tarball compression formats supported by poky, and although bz2
has faster (de)compression time, xz is better in terms of compression ratio:
for all of the rootfs tarballs generated for our currently supported
images/platforms (15 at the moment), the xz format saves an average of 30 MiB
per tarball compared to bz2, totalling up to 450 MiB.
No extra dependencies are pulled in, since xz-native is already being pulled in
for all of our image builds, so the only drawback to this change is the
increased compression time (+7.34s on average per tarball).
https://onedigi.atlassian.net/browse/DEL-9459
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit removes the BOOTLOADER_SEEK_OFFSER, because it has been
moved into the swupdate class and renamed into SWUPDATE_UBOOT_OFFSET.
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
When EXTRA_IMAGE_FEATURES += "overlayfs-etc" is added these
configurations are needed to compile. They are provided with
the default configuration to work with our software.
The user can modify them in their local.conf if needed.
https://onedigi.atlassian.net/browse/DEL-8552
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
Certain platforms share a processor family but need to be differentiated
between them. DEY was using the variable DIGI_FAMILY as the SOM name
rather than the family. It becomes useful to have both (DIGI_SOM as the
more specific, and DIGI_FAMILY as the more generic).
This is the case, for example, of:
- ccmp1 (family)
- ccmp15 (SOM)
- ccmp13 (SOM)
- ccimx8m (family)
- ccimx8mm (SOM)
- ccimx8mn (SOM)
Both variables are used on the machine overrides.
Where DIGI_FAMILY was used, use now DIGI_SOM.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The class 'boot-artifacts.bbclass' was created to generate a
list of the bootable artifacts that must be copied from the
deploy dir to the installer ZIP file, so that the installer
has all the possible bootloader files to update any variant
of the hardware.
The class was somewhat over-engineered to produce the list,
specially for the cc8x, with the variants of SoC revision,
RAM size and width. With the arrival of ST family, it got
more complex, as the artifacts don't even come from U-Boot
recipe.
To remove complexity, this commit removes the bbclass and
moves the list to the platform config file.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
* fix arch tune files path in machine config
* update imx-digi-base config file (using as a base the imx-base.inc
config file in 'meta-freescale')
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
If IMAGE_FEATURE 'read-only-rootfs' is active, the rootfs image
will be SQUASHFS.
Remove other root file system images, such as ext4, ubifs, sdcard.gz
to avoid confusion and use by install scripts.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
These images are comprised of the bootloader, linux and rootfs images. Since
the rootfs images are highly compressable, we can compress the .sdcard file as
well to reduce the space taken up by build artifacts.
https://onedigi.atlassian.net/browse/DEL-7582
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Since these images are highly compressable, this greatly reduces the amount of
space taken up by build artifacts.
Modify the code used to generate the .sdcard and .installer.zip files so that
they contain the decompressed .ext4 image.
https://onedigi.atlassian.net/browse/DEL-7582
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The variable BT_DEVICE_NAME is used to name the Bluetooth device name on
the BlueZ configuration file. Re-use the contents of DIGI_FAMILY (except
for ccimx6qp which re-writes it) to simplify platform definitions.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
- WLAN_P2P_INTERFACE is the same for all platforms: "p2p0".
- WLAN_P2P_DEVICE_NAME can be built out of ${DIGI_FAMILY} except for
the ccimx6qp, that's why it has a weak default assignment.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
WPA and P2P configuration files are basically the same between all
platforms, so we remove all duplicated files to use a common file
and modify it in the recipe logic.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This adds support for U-Boot v2017.03 for all platforms (including CC8X).
For legacy v2015.04:
- Renames u-boot.inc as a versioned file only for v2015.04.
- Moves boot/install scripts from versioned folder into non-versioned
folder (since the scripts remain the same between versions).
For new v2017.03:
- Re-uses poky's u-boot.inc in rocko for v2017.03
- DEY recipe re-writes the do_compile for special U-Boot configuration
required for TrustFence.
- DEY recipe appends the do_deploy, for U-Boot scripts and deploy of
special TrustFence artifacts.
- Adds u-boot-dtb.xxx to UBOOT_CONFIG, required for new U-Boots.
- Adds CC8X scripts.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-5936
As a side effect, remove U-Boot entry point variable and LOADADDR
extra parameter from the kernel recipe.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-5554
This tool was only needed for old kernels, newer kernels use the hardware
random number generator themselves.
https://jira.digi.com/browse/DEL-5518
Signed-off-by: Jose Diaz de Grenu <Jose.DiazdeGrenu@digi.com>
U-Boot has been able to boot kernel zImage for a long time so make this
the default kernel image.
For the CC6 we still want to use uImage for compatibility reasons.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-5237
This commit adds the recipe to update the GPU driver
to the latest version.
https://jira.digi.com/browse/DEL-5234
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit adds the recipe to update the Vivante GPU
driver to the latest version and refresh patches.
https://jira.digi.com/browse/DEL-5082
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Add initial support for Digi's ConnectCore 6 QuadPlus SBC.
The ccimx6qp platform has the QCA6564 chip instead of the
other Atheros chips and included the Atmel ECC508A cryptographic
chip.
https://jira.digi.com/browse/DEL-5082
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
- Added the new image type 'recovery.vfat' to the DEY images
generation process. This new image is a clone of the 'boot.vfat'
but including the recovery ramdisk and the recovery boot script.
- Added the new image type 'recovery.ubifs' to the DEY images
generation process. This new image is similar to the 'boot.ubifs'
but including the recovery ramdisk and the recovery boot script.
Signed-off-by: David Escalona <david.escalona@digi.com>
There are different SBC boards IDs each one having a different
device tree file in the form imx6X-ccimx6sbc-idZZZ.dtb, where:
X is the CPU family (q=Quad/Dual, dl=DualLite/Solo).
ZZZ is the board ID number.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-2160
That's the u-boot configuration used by variants 0x07 and 0x09, which
have been cancelled and are no longer supported by DEY.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
* Merge u-boot-dey-rev_2015.04.inc into the recipe. There is no need to
split the recipe, as there is no other recipe using this u-boot code.
* Update uboot configurations to the new format '_defconfig'. Also add
the new 2GB variant.
* Remove PREFERRED_VERSION_u-boot-dey for CC6, as there is only one
version available for this platform.
https://jira.digi.com/browse/DEL-1829
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Linux 3.10 is still available via project's local.conf.
PREFERRED_VERSION_linux-dey = "3.10"
KERNEL_DEVICETREE = "..."
https://jira.digi.com/browse/DEL-1748
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This is needed in the context of CC6 variants 0x7 and 0x9 (EMMC-less).
Changes:
* Do not use 'meta-fsl-arm' image generation class: removed include and
override SDCARD generation function
* Use same VFAT boot image for EMMC and SD card. The u-boot bootscript
has been adapted to be able to boot Linux from both SD and EMMC.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
(cherry picked from commit 8b8456b8fd90facd92dfc87632effa582ca60475)
This will allow in following commit to use the same VFAT boot image for
EMMC and SD. Until now we were creating different boot images for EMMC
and SD card images.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
(cherry picked from commit 13e9ec7608d42430c2a01a728d030752a71f7948)
Use Yocto's UBOOT_CONFIG new functionality to select the u-boot
configuration to build.
https://jira.digi.com/browse/DEL-1584
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Remove the current DEY variants support and framework for CC6 because in
following commits we will add support for all *hardware* variants in
just one set of DEY images for CC6.
https://jira.digi.com/browse/DEL-1569
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Arturo Buzarra
Hector Palacios
Gabriel Valcazar
Mike Engel
Javier Viguera
Francisco Gil
Jose Diaz de Grenu
David Escalona
Alex Gonzalez