If IMAGE_FEATURE 'read-only-rootfs' is active, the rootfs image
will be SQUASHFS.
Remove other root file system images, such as ext4, ubifs, sdcard.gz
to avoid confusion and use by install scripts.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
These images are comprised of the bootloader, linux and rootfs images. Since
the rootfs images are highly compressable, we can compress the .sdcard file as
well to reduce the space taken up by build artifacts.
https://onedigi.atlassian.net/browse/DEL-7582
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Since these images are highly compressable, this greatly reduces the amount of
space taken up by build artifacts.
Modify the code used to generate the .sdcard and .installer.zip files so that
they contain the decompressed .ext4 image.
https://onedigi.atlassian.net/browse/DEL-7582
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Since this overlay is only used in the SBC Pro bootscript, have a separate
bootscript for the SBC Express.
https://jira.digi.com/browse/DEL-7276
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Follow the syntax:
_ov_<som|board>_<functionality>[_<hardware>].dts
where:
_ov_ identifies the file as an overlay.
som|board identifies whether the overlay applies to the SOM
or to the carrier board.
functionality identifies the function of the overlay.
hardware identifies the hardware to which the overlay
applies.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Each platform now has only one base device tree, meant for the i.MX8DX variants
of the ccimx8x boards. Apply the QXP overlay in the bootscript if the SOC is
identified as an i.MX8QXP.
Since we want to give this overlay a higher priority than the SOM overlays
(wifi and bluetooth), prepend it to the overlay list after appending the SOM
overlays.
https://jira.digi.com/browse/DEL-7100
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
These overlays aren't handled in our bootscript, but we make them available for
users in case they wish to use alternative interface configurations.
https://jira.digi.com/browse/DEL-7100
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Remove the old wb device trees from the ccimx8x-sbc-express and ccimx8x-sbc-pro
configuration files and add the ccimx8x wifi and bt overlays. Modify both
platforms' bootscripts to apply the overlays depending on board_id, hardware
capabilities or module variants.
https://jira.digi.com/browse/DEL-7100
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit adds a installation script that uses fastboot support to
update the target firmware.
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
https://jira.digi.com/browse/DEL-6845
Additionally:
- The handling of gpios has been swapped so 'Set low XBEE_SLEEP_RQ' is done
before 'Power cycle XBEE_RESET_N' to assure the device doesn't enter sleep mode.
- Removed ExecStop entry from systemd service since it's doing nothing.
https://jira.digi.com/browse/DEL-6424https://jira.digi.com/browse/DEL-6423
Signed-off-by: Hector Bujanda <hector.bujanda@digi.com>
WPA and P2P configuration files are basically the same between all
platforms, so we remove all duplicated files to use a common file
and modify it in the recipe logic.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
With the arrival of DualX variants, the devicetree files have changed
their names to include the soc type (qxp, dx).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-6641
This recipe adds a script and a related systemd service that
configures two GPIOs (user defined, or else platform-defaults) as
output and sets them to the appropriate value for initializing the
XBee socket:
- XBEE_SLEEP_RQ: is set low, for running the XBee
- XBEE_RESET_N: is set low and then high, to reset the XBee
The service triggers on the condition that the UART TTY device node
pointed to by variable XBEE_UART exists.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-6366