NAND partitions may have pre-existing UBI volume information
and that will tell U-Boot to use 'ubiwrite' to keep UBI wear
leveling information instead of erasing the NAND partition
beforehand. Given that the UBI support in U-Boot is not
particularly complete and stable, and specially if the NAND
partition table has been changed, this could result into
problems during the UBI volume initialization or during the
update process. To prevent such problems it is better that
the NAND partitions are erased.
This loses the UBI wear leveling information but provides
a more reliable deployment install script.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DUB-718
Modify patch to clean compiler warning:
warning: passing argument 1 of 'sysfs_mmcboot_set_protection' discards
'const' qualifier from pointer target type
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Remove the commit that removes the p2p0 interface at boot. This interface
is the one used to establish p2p connections. Configuring the wlan0 command
for p2p does not work.
https://jira.digi.com/browse/DEL-3390
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
The qualcomm wlan driver creates two interfaces at load time, wlan0 and
p2p0. Both of them should load the module if not already loaded.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
This commit adds a wpa supplicant P2P configuration file and configures
the p2p0 interface automatically at pre-up.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Even though this variable is documented as unused, removing it fails
wireless regression tests.
https://jira.digi.com/browse/DEL-3501
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
This re-enables USB mass storage support that was unintentionally
removed in commit 6851ab23e4.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DUB-713
The dependence on virtual/kernel is added implicitly through the module
class, so there is no need to add it explicitly.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This updates the kernel configuration to the latest one
which disables unused drivers and options to optimize the
kernel size.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The following document,
JQCA61x4, QCA65x4, and QCA937x
Configuration Parameters Specification
80-Y7674-11 Rev. J
September 30, 2016
Contains a list of unused configuration arguments in page 29. This commit
removes those listed arguments that appeared on the default configuration
file to avoid confusion.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Otherwise the module is built with debug as that is the Makefile's
default.
https://jira.digi.com/browse/DEL-3392
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
Implements functions to get and set variables from U-Boot's environment.
https://jira.digi.com/browse/DEL-3358
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
These have been provided by the embedded hardware team and they are to
be used for certification testing. The calibration corresponds to the
internal antenna on the module. If using the current external antenna on the
CC6UL SBC they work fine, although they could be tweaked to improve.
The BDF files provided were generated from the original ones, by running a
test tree for output power calibration for QCA6564A-3 chip. This test
tree is called
‘FCCSP_Rome3.x_WLAN_CLPC_cal_and_WLAN_BT_Verify_Y8611-H341.xtt’ and it
belongs to the Qualcomm Design Package ‘DP25-WL420-100’.
The test tree is to be run in the QSPR software tool, part of the QDART
software tools set provided by Qualcomm.
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
As discovered during certifications preparation work, calibration changes
applied only on the bdwlan30.bin file do not take effect.
Per QCA guidelines, the bdwlan30.bin and utfbd30.bin files should be the
same for the calibration changes to work.
This commit removes the current utfbd30.bin file, with an md5sum that
matches the original bdwlan30.bin file in QCA's chipcode
qca6564-le-1-0-3_qca_device repository, and creates a symbolic link to the
actual bdwlan30.bin board file used to certify Digi's module internal
antenna.
https://jira.digi.com/browse/DEL-3454
Signed-off-by: Alex Gonzalez <alex.gonzalez@digi.com>
The codec MAX98088 present on the ccimx6ulsbc only needs one
configuration file that can play and record.
The default file enables the interfaces present on the ccimx6ulsbc:
- Headphones
- Speaker
- LineOut (in stereo mode)
- LineIN-A
- MIC2
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-2352
- Added the new image type 'recovery.vfat' to the DEY images
generation process. This new image is a clone of the 'boot.vfat'
but including the recovery ramdisk and the recovery boot script.
- Added the new image type 'recovery.ubifs' to the DEY images
generation process. This new image is similar to the 'boot.ubifs'
but including the recovery ramdisk and the recovery boot script.
Signed-off-by: David Escalona <david.escalona@digi.com>
The i.MX6UL supports some basic multimedia functionality
using the pixel pipeline (PXP).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-2358
The patch with the same name in 'meta-swupdate' fails to apply cleanly
after the patches we have done in meta-digi. So add here a version of
the patch that applies cleanly and with higher precedence in the search
path (using 'dey' distro override).
https://jira.digi.com/browse/DEL-3355
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
The kernel recipe was modifying the device tree blobs in place within the
kernel build temporal directory. This can cause problems after several
compilations, only the deployed artifacts should be signed/encrypted.
The deployment of the DTBs is done by do_deploy_appends in other layers which
are appended after this recipe, so it is required to use a postfunc to do the
trustfence related process after the deployment of all the artifacts.
https://jira.digi.com/browse/DEL-3388
Signed-off-by: Diaz de Grenu, Jose <Jose.DiazdeGrenu@digi.com>
This application can be used to:
- Update the MCA firmware
- Configure the tamper settings
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-3230
Javier Viguera
Hector Palacios
Alejandro Navarro
David Escalona
Alex Gonzalez
Diaz de Grenu, Jose