U-Boot has embedded support to handle bootcount tries.
When the limit of tries is reached, U-Boot runs the script
in `altbootcmd` rather than the usual `bootcmd`.
This other script resides on meta-digi-dualboot layer.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
Ensure stdout redirection to the USB interface is removed in every case.
Otherwise, it would be left redirected when INSTALL_UBOOT_FILENAME is
manually set.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Install scripts may rework the partition table basing on the value of
env variables. Information of UBI volumes may remain on the NAND that
could later not correspond to the new partition table.
Make sure the MTD partitions are erased prior to updating:
- For Multi-MTD, append '-e' option to the update command.
- For Single-MTD, erase the system partition.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Check the status of 'dualboot' env variable.
If set to "yes", use the dualboot partition table in the script and
restore the variable (default is "no") after resetting the environment.
Also, for dualboot, there's no need to wipe the recovery partition or
boot into recovery mode.
For dualboot, this script programs both systems A and B with the same
images.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-7649
Commit c33fc8a7fe wrongly used
https protocol when using MTK remote when it should have been
ssh.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
When we added the SDMA fw systemd service, we accidentally made it so that all
scripts were installed only when using systemd. These files are still needed
when using sysvinit, so correct this change.
While at it, include the SDMA fw service in firmware-imx-sdma's FILES.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
When DualBoot mechanism is enabled and an update is pending,
the boot script needs to change certain variables and save the
environment.
The regular boot script already changes a number of variables,
such as 'extra_bootargs' and 'overlays' by appending strings to
the already existing values. Saving the envionment may make these
grow endlessly with each iteration of the boot script.
For this reason, move the DualBoot check as the first thing in
the script, save the environment if needed, and then continue
with the normal flow, that changes variables before booting
but doesn't save them.
On certain scripts, this allows us to get rid of some instructions
for resetting the overlays variable.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The script required the passing of option '-b' for setting up the
target to use a single MTD partition and multiple UBI volumes.
If a target however already has the variable 'ubisysvols' set to
'yes' but this parameter is forgotten when calling the script, the
partition layout would change to default (several MTD partitions).
Remove the recently added '-b' option and make the script decide
basing on the current value of 'ubisysvols' variable.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The script preserves the current value of env variable 'ubisysvols'
so that the new partition script generates the appropriate partition
table before proceeding with the update operations.
If using a UBI volumes layout, the script will not erase the partitions.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-7614
With U-Boot supporting the creation of mtdparts and UBI volumes depending
on the value of variable 'ubisysvols', adapt the install script to make
use of those to generate a partition table and UBI volumes accordingly.
This can be triggered with new option '-b'.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Set the new variable 'rootfsvol' to rootfs_a or rootfs_b when dualboot is
enabled, to cover the case where the devices uses the 'system' partition
with different UBI volumes.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The support for dualboot was integrated on meta-digi-dualboot layer, but it
really depends only on environment variable 'dualboot' so we'd better
integrate the support on the scripts in meta-digi, to avoid synchonization
problems between both layers.
This also allows to be able to easily enable dualboot in U-Boot with the
variable, without needing to update the script on the linux partition.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Enabling DIGI_INTERNAL_GIT defaults to LOG server. The build from local
MTK Digi server was broken.
Fix uboot and linux recipes declaring different repo paths depending on
whether the local remote is LOG or MTK.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
When we added the SDMA fw systemd service, we accidentally made it so that all
scripts were installed only when using systemd. These files are still needed
when using sysvinit, so correct this change.
While at it, include the SDMA fw service in firmware-imx-sdma's FILES.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This command was already present on the script used for CC8X. Add it here
so the scripts are as much alike as possible.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Fastboot is configured on boot with the current MMC configuration.
If we create a GPT partition table, we need to restart fastboot before we
try to program any partition with the 'flash' fastboot command.
Set 'fastboot_dev' to a different device, 'sata' for example an back to 'mmc'
to trigger a fastboot restart after creating the partition table on blank
devices.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
The current syntax only works properly when running the script through bash.
Change this so that it works for other shells as well.
While at it, fix a typo in the message that appears when the variant can't be
detected in the 6UL script.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
We document how to use this script from the Yocto image directory. Now that the
*.ext4 files are compressed by default, the script needs to automatically
decompress said files before starting the update process.
https://onedigi.atlassian.net/browse/DEL-7582
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit adds the Edge TPU simple camera examples to exercise the Google
Coral devices with Digi Embedded Yocto.
https://onedigi.atlassian.net/browse/DEL-7547
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit adds the required libraries and packages to exercise the Google
Coral devices with Digi Embedded Yocto.
https://onedigi.atlassian.net/browse/DEL-7547
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The install script of cc8x had errors (using double '==' instead
of single on comparisions).
Besides fixing this typo, this commit changes the logic to:
- default to 2GB U-Boot for variants other than the ones in the
list.
- consider variant code 0x00 (not programmed HWID) as a failure.
thus forcing the user to specify the file on the command line.
This second action is done also on the cc6ul script.
Reported-by: Hector Bujanda <hector.bujanda@digi.com>
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Update US Board Data File to include the changes required to pass the
EN 300 328 V2.2.2 blocking test.
The new BDF is:
- bdwlan30_US.bin (24140b5c28256cadfd95bc28fc574733)
https://onedigi.atlassian.net/browse/DEL-7576
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
install_abort is a temp variable so 'test -n' doesn't work on it.
This was fixed in all scripts except the USB script of ccimx6sbc.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
- Check the existence of files before the 10 second wait.
- Print the list of filenames to program to each partition.
- Print the file that's being updated to each partition.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
With the generalization done in previous commits, we have now several files
that are identical and can be merged into a common SOM or SOM family
folder.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Create global variables:
DEFAULT_IMAGE_NAME
GRAPHICAL_IMAGES
to have them substituted on the U-Boot install scripts for better
generalization.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
U-Boot install scripts (from uSD and USB) were hard-coded to dey-image-qt.
Allow to install other image files by setting a new variable 'image-name'
which defaults to 'dey-image-qt' if not defined, except for the CC6UL
SBC Express, that defaults to 'core-image-base'.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7385https://jira.digi.com/browse/DEL-7333
On these boot scripts, this variable is not used, so we can remove it.
Besides, it's generated by U-Boot code.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Use ##MACHINE## placeholder to have it later substituted by the recipe
using Yocto ${MACHINE} variable.
This will help later reducing the number of files to have one per SOM
(or even family) instead of one per platform.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Otherwise, the name of the file will be "u-boot-dey-initial-env", causing
errors when reading the default environment from userspace, since libubootenv
expects "u-boot-initial-env" instead.
https://onedigi.atlassian.net/browse/DEL-7566
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit adds the sdma-firmware.service to the rootfs
to load the SDMA firmware during boot, that is necessary
for some drivers to work correctly.
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
Non-graphical images (core-image-base, dey-image-aws) don't contain the
graphic-backend on their filenames.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
- Determine first the filenames and abort if any does not exist.
- Print a warning message about the erasing of the media with a list
of partitions and files to use for the update
- Sync the different scripts so they look more similar
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7333
Similar to how it's done on the ccimx6ul, create a function for updating
a partition with a file, that also prints a message.
Rename the function to be the same in all scripts.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7333
Previously, this script only allowed the U-Boot filename as parameter.
This commit makes use of getopts() to pass the following options to the
script:
-h, for help
-i, to pass the dey image name that prefixes the firmware filenames
-n, to skip the 10 seconds delay that allow you to cancel the process
-u, to pass the U-Boot filename
The default image name (if none passed) keeps being 'dey-image-qt' but the
new option allows reusing this script to install dey-image-webkit or
dey-image-aws images.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7385
The prebuilt 'athtestcmd' binary allows you to test tx/rx of the
Wi-Fi MAC, when the driver is loaded in test mode.
This is required for certifying Wi-Fi in products, so add it by
default for the ccimx6sbc.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7444
(cherry picked from commit acb402fdcfa54d8d5519580ff7fcfb76fbed3f49)
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Since this feature was introduced in newer versions of U-Boot, we need
to disable it for v2017.03 to avoid several compilation issues.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Update US Board Data File to use the new GOLDEN2 calibration.
The new BDF is:
- bdwlan30_US.bin (328f970444b5eaaa48c0188cea1685e3)
https://jira.digi.com/browse/CC6UL-1210
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
(cherry picked from commit 373b3958bad9d0c462349d89ef5832e843624b01)
This commit fixes the following warning:
WARNING: meta-digi/meta-digi-arm/recipes-bsp/trustfence-cst/trustfence-cst_3.3.1.bb:
Recipe trustfence-cst sets S variable with trailing slash '/tmp/work/aarch64-dey-linux/trustfence-cst/3.3.1-r0/cst-3.3.1/',
remove it
https://jira.digi.com/browse/DEL-7508
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This default environment is needed by packages like libubootenv.
https://jira.digi.com/browse/DEL-7508
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This package has been entirely replaced with libubootenv
https://jira.digi.com/browse/DEL-7410
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This is a replacement for u-boot-fw-utils. Adapt the u-boot-fw-utils patches
to this new library and include the same logic as the u-boot-fw-utils recipe
(generate and install the U-Boot environment configuration file in the rootfs)
For now, remove the u-boot-default-env dependency, since the package doesn't
exist in zeus.
https://jira.digi.com/browse/DEL-7410
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The new SCFW re-enables "Read DBI deskew configuration"
setting, to support Nanya LPDDR4 chips.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/CC8X-297
Add a patch series to customize the ATF console for the ConnectCore 8M platforms,
and to disable the Cortex-M debug UART.
https://jira.digi.com/browse/DEL-7497
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Update file:
- bdwlan30_US.bin (93a58f0f8e241bef6600d53d013c3cb2)
This file was generated by calibrating several v3 CC8MN SOMs and
merging their resulting BDF files into a new Golden file.
Target output powers tables and CTL tables remain intact.
Reference calibration file is obtained from 'qca6574au-le-2-2-2_qca_oem' repo
at tag 'r00005.1' under path
'wlanfw/cnss_proc/wlan/fw/target/sdio_dst/qc6174/bdwlan30.bin':
- bdwlan30.bin (8a40d95698825e1718bee640b1f7982a)
Target output powers respect the maximum EVM for every data rate.
CTL limits comply with FCC, CE and TELEC certifications.
https://jira.digi.com/browse/DEL-7487
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
(cherry picked from commit cceffef831edd10b017aac3006636c98f7baa0a9)
Update file:
- bdwlan30_US.bin (93a58f0f8e241bef6600d53d013c3cb2)
This file was generated by calibrating several v3 CC8MN SOMs and
merging their resulting BDF files into a new Golden file.
Target output powers tables and CTL tables remain intact.
Reference calibration file is obtained from 'qca6574au-le-2-2-2_qca_oem' repo
at tag 'r00005.1' under path
'wlanfw/cnss_proc/wlan/fw/target/sdio_dst/qc6174/bdwlan30.bin':
- bdwlan30.bin (8a40d95698825e1718bee640b1f7982a)
Target output powers respect the maximum EVM for every data rate.
CTL limits comply with FCC, CE and TELEC certifications.
https://jira.digi.com/browse/DEL-7487
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
(cherry picked from commit cceffef831edd10b017aac3006636c98f7baa0a9)
There's a Yocto configuration option that enables this feature in U-Boot, but
since imx-boot images are signed using the scripts in trustfence-sign-tools,
said configuration is lost and the scripts don't take it into account if it's
enabled. Make sure that the configuation carries over to the script.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Allow users to select Certified Bluetooth 4.1, rather than
the default not-certified Bluetooth 5, through the use of variable
BT_FW_VERSION="4"
md5sums:
nvm_tlv_3.2.bin ==> 9621f50172f2bfb4f65f8e5c6528b614
rampatch_tlv_3.2.tlv ==> 769e1fc9e5a2061bb3aaa1f32dac3804
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
This overlay added cooling devices for all quad cores.
On the latest BSP, the SoC device tree include contains all four
cooling devices and the newest U-Boot is able to delete the nodes
for non-existing cores, so there's no need for this overlay
anymore.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Otherwise, mkimage will delete the device trees between imx-boot builds,
causing the build to fail when generating a signed imx-boot.
https://jira.digi.com/browse/DEL-7420
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
ConnectCore 8M Mini has support to VPU but the library used is different than
the used by the i.MX6 processors. This recipe manages the required libraries
to operate with this kind of VPU.
https://jira.digi.com/browse/DEL-7397
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The Cortex-M4 uses the UART4 as debug console, and it is
shared with the Cortex-A53. This commit disables it for the
ConnectCore 8M Mini DVK board to avoid conflicts.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Both ConnectCore 8M platforms share the same U-Boot build process,
so apply the same changes for them.
https://jira.digi.com/browse/DEL-7397
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Use the same common files for both ConnectCore 8M platforms
https://jira.digi.com/browse/DEL-7397
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Use the same common files for both ConnectCore 8M platforms
https://jira.digi.com/browse/DEL-7397
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Use the same common files for both ConnectCore 8M platforms
https://jira.digi.com/browse/DEL-7397
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
When manually changing the partition table, it could happen that
a UBI volume already exists in the 'update' partition.
If not erased, the system may find the old UBI volume (with wrong
geometry information) and try to mount it which will result in
failure.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
On commit 1e5cafeb79 a fall-back
update command was introduced in case the newest command fails.
If the newest command succeeds, however, the 'test' command for
error doesn't match (there is no error) and the return code of
such test is "1". On the next check for errors, this results on
an error, when we really mean to continue because the first
command was successful.
Move the second error check inside the error path of the first
attempt.
Reported-by: Francisco Gil <francisco.gilmartinez@digi.com>
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
In order to revoke SRKs in platforms with AHAB we need to set a mask
during the signing/encryption process.
Create new TRUSTFENCE_SRK_REVOKE_MASK variable to export the
SRK_REVOKE_MASK variable required by the imx-boot signing script.
The revoke mask is not necessary for signing/encryption of other artifacts,
so set it by default to 0x0.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
The 'source file system' was removed as an argument from the
'update' command in U-Boot v2020.04.
For platforms using such version, remove it from the update fw
scripts.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DUB-983
This command isn't essential and might not be available on all systems, so
remove it. Use the "oflag=sync" dd parameter instead.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
A similar change was done in the dey-3.0/maint branch for the uSD installation
scripts, but since USB scripts were added in dey-3.0/master, apply the same
to them as well.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Since there is only 1 supported version of cst, the include file is
only used once.
Move all the recipe implementation to the *.bb recipe and remove the
*.inc file.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Since cst-3.3.1 is now distributed with a BSD-3-Clause license, it is allowed
to distribute its source code from the Digi FTP.
Fetch the tarball from that location.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
CC8X SOMs code the RAM size on the OTP bits so this fall-back table
shouldn't be necessary, but update it with latest variants just
in case.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Add Compliance Test Limits (CTL) information for FCC, CE and TELEC
certifications to the CC8MN US Board Data File.
The rest of the file (calibration, target power levels, etc.) remains
intact.
Updated file:
- bdwlan30_US.bin (MD5SUM: f9600f7bf4d601494b9bbe1ccbe94d6a)
https://jira.digi.com/browse/DEL-7359
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
CST was being built linking to the openssl libcrypto library from the host.
When the openssl version in the host didn't match the version in the SDK,
the SDK build failed like this:
Error:
Problem 1: package nativesdk-packagegroup-sdk-host-1.0-r12.0.x86_64_nativesdk requires nativesdk-trustfence-cst, but none of the providers can be installed
- conflicting requests
- nothing provides libcrypto.so.1.0.0()(64bit) needed by nativesdk-trustfence-cst-3.3.1-r0.0.x86_64_nativesdk
- nothing provides libcrypto.so.1.0.0(OPENSSL_1.0.0)(64bit) needed by nativesdk-trustfence-cst-3.3.1-r0.0.x86_64_nativesdk
- nothing provides libcrypto.so.1.0.0(OPENSSL_1.0.1)(64bit) needed by nativesdk-trustfence-cst-3.3.1-r0.0.x86_64_nativesdk
Problem 2: package nativesdk-packagegroup-qt5-toolchain-host-1.0-r0.0.x86_64_nativesdk requires nativesdk-packagegroup-sdk-host, but none of the providers can be installed
- package nativesdk-packagegroup-sdk-host-1.0-r12.0.x86_64_nativesdk requires nativesdk-trustfence-cst, but none of the providers can be installed
- conflicting requests
- nothing provides libcrypto.so.1.0.0()(64bit) needed by nativesdk-trustfence-cst-3.3.1-r0.0.x86_64_nativesdk
- nothing provides libcrypto.so.1.0.0(OPENSSL_1.0.0)(64bit) needed by nativesdk-trustfence-cst-3.3.1-r0.0.x86_64_nativesdk
- nothing provides libcrypto.so.1.0.0(OPENSSL_1.0.1)(64bit) needed by nativesdk-trustfence-cst-3.3.1-r0.0.x86_64_nativesdk
Fix that by adding the native dependencies include and lib folders to
the CST build. Also add openssl-native as a dependency for the SDK build,
otherwise it wont link to the SDK libcrypto library.
Additionally, to allow running CST in a host machine where the openssl version
does not match the version in the SDK, libcrypto library is statically linked.
https://jira.digi.com/browse/DEL-7346
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
(cherry picked from commit a95b3ad602)
CST was being built linking to the openssl libcrypto library from the host.
When the openssl version in the host didn't match the version in the SDK,
the SDK build failed like this:
Error:
Problem 1: package nativesdk-packagegroup-sdk-host-1.0-r12.0.x86_64_nativesdk requires nativesdk-trustfence-cst, but none of the providers can be installed
- conflicting requests
- nothing provides libcrypto.so.1.0.0()(64bit) needed by nativesdk-trustfence-cst-3.3.1-r0.0.x86_64_nativesdk
- nothing provides libcrypto.so.1.0.0(OPENSSL_1.0.0)(64bit) needed by nativesdk-trustfence-cst-3.3.1-r0.0.x86_64_nativesdk
- nothing provides libcrypto.so.1.0.0(OPENSSL_1.0.1)(64bit) needed by nativesdk-trustfence-cst-3.3.1-r0.0.x86_64_nativesdk
Problem 2: package nativesdk-packagegroup-qt5-toolchain-host-1.0-r0.0.x86_64_nativesdk requires nativesdk-packagegroup-sdk-host, but none of the providers can be installed
- package nativesdk-packagegroup-sdk-host-1.0-r12.0.x86_64_nativesdk requires nativesdk-trustfence-cst, but none of the providers can be installed
- conflicting requests
- nothing provides libcrypto.so.1.0.0()(64bit) needed by nativesdk-trustfence-cst-3.3.1-r0.0.x86_64_nativesdk
- nothing provides libcrypto.so.1.0.0(OPENSSL_1.0.0)(64bit) needed by nativesdk-trustfence-cst-3.3.1-r0.0.x86_64_nativesdk
- nothing provides libcrypto.so.1.0.0(OPENSSL_1.0.1)(64bit) needed by nativesdk-trustfence-cst-3.3.1-r0.0.x86_64_nativesdk
Fix that by adding the native dependencies include and lib folders to
the CST build. Also add openssl-native as a dependency for the SDK build,
otherwise it wont link to the SDK libcrypto library.
Additionally, to allow running CST in a host machine where the openssl version
does not match the version in the SDK, libcrypto library is statically linked.
https://jira.digi.com/browse/DEL-7346
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Create scripts to install DEY firmware using a USB stick.
https://jira.digi.com/browse/DEL-6802
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
U-Boot v2020.04 for the CC6UL supports the fastboot protocol.
Create scripts to install DEY firmware via USB using uuu
tool.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Update file:
- bdwlan30_US.bin (388da992fdf0bd25e62060247a0606e5)
This file was generated by calibrating several v3 CC8MN SOMs and
merging their resulting BDF files into a Golden file.
It also encodes the Target output powers tables.
Reference calibration file is obtained from 'qca6574au-le-2-2-2_qca_oem' repo
at tag 'r00005.1' under path
'wlanfw/cnss_proc/wlan/fw/target/sdio_dst/qc6174/bdwlan30.bin':
- bdwlan30.bin (8a40d95698825e1718bee640b1f7982a)
Target output powers respect the maximum EVM for every data rate.
https://jira.digi.com/browse/DEL-7290
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Includes:
imx-vpu: Fix selected version for 6Q and 6DL [LF-1816]
An older version of imx-vpu, from upstream, is being selected
for the image instead of the current one. The problem is
the override imxvpucnm used for the COMPATIBLE_MACHINE
is no longer being used. Update the recipe to use SOC
overrides instead.
Signed-off-by: Tom Hochstein <tom.hochstein@nxp.com>
Signed-off-by: Hector Bujanda <Hector.Bujanda@digi.com>
Includes:
imx-seco-libs: Switch branch to imx_5.4.47_2.2.0
multilib: imx-seco-libs: Fix LIBDIR
imx-seco.inc: use c0 for 8dxl phantom with new c0 boards
Signed-off-by: Hector Bujanda <Hector.Bujanda@digi.com>
Includes:
imx-boot_1.0.bb: Update M4 binary name for i.MX 8QM [YOCIMX-4866]
8QM M4 demos unified the binary name.
Change name make it more easy for understanding.
imx-boot: Update the build option for iMX 8DXL Phantom C0 new boards [YOCIMX-4663]
Signed-off-by: Hector Bujanda <Hector.Bujanda@digi.com>
Build the U-Boot for variants with 1GB of memory and make the installation and
boot scripts recognize all of the current variants.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Since this overlay is only used in the SBC Pro bootscript, have a separate
bootscript for the SBC Express.
https://jira.digi.com/browse/DEL-7276
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Update file:
- bdwlan30_US.bin (8c8b575fb9a65714df0b7c6cb3399ed6)
This file was generated by calibrating several CC8MN SOMs from spin 3
and merging their resulting BDF files into a Golden file.
It also encodes the Target output powers.
Reference calibration file is obtained from 'qca6574au-le-2-2-2_qca_oem' repo
at tag 'r00005.1' under path
'wlanfw/cnss_proc/wlan/fw/target/sdio_dst/qc6174/bdwlan30.bin':
- bdwlan30.bin (8a40d95698825e1718bee640b1f7982a)
Target output powers respect the maximum EVM for every data rate.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
The boot script appends values to certain variables such as
$extra_bootargs and $overlays.
If the final instruction of the boot script (dboot command)
fails, these variables contain the new values, plus the original
one. Since the user recovers the prompt, he may do a 'saveenv'
to save the environment, and the modified variables will be
saved, only to be enlarged again on the next boot.
This can lead to repeated strings on such variables.
Save the original value and restore it in case of failure on
the dboot command.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Follow the syntax:
_ov_<som|board>_<functionality>[_<hardware>].dts
where:
_ov_ identifies the file as an overlay.
som|board identifies whether the overlay applies to the SOM
or to the carrier board.
functionality identifies the function of the overlay.
hardware identifies the hardware to which the overlay
applies.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Wrapping unterminated lines doesn't work for scripts (even
if they contain the backslash).
Substitute with full non-wrapped if/elif sentences.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7252
In the ccimx6sbc, since each SOC has a separate set of device trees, we can use
the soc_family environment variable when generating the name of the final
device tree in the bootscript. However, for the ccimx6qpsbc, there is only one
set of device trees with the "imx6qp" prefix, even though there are SOC
variants such as the imx6dp. Running the bootscript on a ccimx6qpsbc with an
imx6dp SOC assembled will result in a failure, since it will look for a
non-existing device tree starting with a "imx6dp" prefix.
Stop using the soc_family variable and hardcode "imx6qp" instead.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
With the latest version of imx-mkimage, the original dtb file is being
removed at the end of the build.
Add a patch to preserve it and be able to run several builds during the
same compile run, like we do for imx-boot signing.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
The CST package requires byacc to compile, and even though this dependency is
met when building images for the target, said dependency needs to be made
explicit when the package is built for the SDK in order to avoid build errors.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
With the previous solution we would need to generate
multiple overlays for each soc_type, so if we have a
new soc type (for example the solo), we would need
to generate 3 different overlays.
Signed-off-by: Francisco Gil Martinez <francisco.gilmartinez@digi.com>
This commit fixed the sdcard generation when encryption is enabled.
In the sdcard image always is included the signed image instead of the
encrypted.
https://jira.digi.com/browse/DEL-7200
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This version supports encryption for devices with Advanced High Assurance Boot
(AHAB) capabilities. This commit also updates and simplifies Digi custom
patches.
https://jira.digi.com/browse/DEL-7175
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Add running 'mmc partconf 0 1 1 1' command to the uuu scripts after
writing the new U-Boot into the internal eMMC.
This is required for blank eMMCs on CC8MN and CC8X SOMs where the
'update' command has never been run to be able to boot from eMMC.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
The encryption of the U-Boot environment uses the HWID as key
modifier. The HWID was being read using the fsl_otp driver sysfs
entries and over two words. The driver is now deprecated and also
the cc8x and cc8m platforms have different number of HWID words.
This patch modifies the function that reads the HWID words by
using new entries on the device tree 'digi,hwid_X' where X is the
index of the HWID word.
It also removes the need to select CONFIG_MD5 which is already
auto-selected on sandbox_defconfig by other config switches.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7185
(cherry picked from commit 8ced362766)
The encryption of the U-Boot environment uses the HWID as key
modifier. The HWID was being read using the fsl_otp driver sysfs
entries and over two words. The driver is now deprecated and also
the cc8x and cc8m platforms have different number of HWID words.
This patch modifies the function that reads the HWID words by
using new entries on the device tree 'digi,hwid_X' where X is the
index of the HWID word.
It also removes the need to select CONFIG_MD5 which is already
auto-selected on sandbox_defconfig by other config switches.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7185
The Cortex-M7 uses the UART4 as debug console, and it is
shared with the Cortex-A53. This commit disables it for the
ConnectCore 8M Nano DVK board to avoid conflicts.
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
Store mkimage log for every built target so it can be later used by the
signing script to create the correct CSF file for every target.
https://jira.digi.com/browse/DEL-7158
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
The mkimage.log file is required by the signing script to create the CSF file.
Since there is one mkimage log file per target, update the mkimage.log symlink
right before signing the imx-boot file to ensure creating the CSF with the
corresponding mkimage log for every target.
https://jira.digi.com/browse/DEL-7158
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
This commit updates to the NXP imx-5.4.24-2.1.0 BSP.
Including following changes
In M4 MCUX SDK 2.8.0, it added PMS demo for CM40 to support Partition
reboot feature besides rpmsg pingpong. So change the m40 default image
to imx8qm_m4_0_TCM_power_mode_switch_m40.bin
Build i.MX 8DXL flash_linux_m4 with V2X off
Use option V2X=NO to switch V2X off.
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
imx-boot files for target flash_regression_linux_m4 fail the signature
process, so skip them while signing the rest of the targets.
https://jira.digi.com/browse/DEL-7158
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
When loading the wireless driver in test mode, the UTF firmware file
is loaded.
On pcie chips, the UTF file is expected to be named 'utf.bin'.
On sdio chips, the UTF file is expected to be named 'utf30.bin'.
Rename the pcie UTF file to match this requirement.
md5sum
----------------------------------------------------------
qca65X4_pcie: utf.bin -> 41cfb4e50613cd0eeb0fa99a005131bd
qca65X4_sdio: utf30.bin -> 4743dee015047752e433e69f4db89974
https://jira.digi.com/browse/DEL-7086
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Add Compliance Test Limits (CTL) information for FCC, CE and TELEC
certifications to the CC8X US Board Data File.
The rest of the file (calibration, target power levels, etc.) remains
intact.
Updated file:
- bdwlan30_US.bin (MD5SUM: 100a982b33b4a2cfeb34cdea794dc6d6)
https://jira.digi.com/browse/DEL-6995
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Signed imx-boot files had the '-signed' appended at the end of the file.
Add it after the file prefix instead, so it is easier to replace using an
unsigned file for a signed one just by changing the file prefix.
https://jira.digi.com/browse/DEL-7024
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
The '-fmacro-prefix' option is a new GCC option introduced in gcc version 8.
To keep compatibility with previous GCC versions, remove this option from
the DEBUG_PREFIX_MAP list so nativesdk builds are able to compile this recipe.
Following is the compilation issue avoided by this patch:
| gcc: error: unrecognized command line option ‘-fmacro-prefix-map=<yocto-workspace>/tmp/work/x86_64-nativesdk-deysdk-linux/nativesdk-imx-mkimage/git-r0=/usr/src/debug/nativesdk-imx-mkimage/git-r0’
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
This recipe is now built as native and nativesdk by means of the
BBCLASSEXTEND configuration.
Remove every remaining legacy native configuration since all will be covered
by the class extension.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
This service is the same as the one provided by NXP, but with altered
dependencies. Start it before the kernel modules are loaded so the firmware is
ready by the time the mcp25xxfd module is loaded.
https://jira.digi.com/browse/DEL-7114
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The signing script is used for signing multiple artifacts, not just the
kernel, so rename it for a broader use.
https://jira.digi.com/browse/DEL-7047
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Francisco Gil
Gonzalo Ruiz
Hector Palacios
Gabriel Valcazar
Mike Engel
Arturo Buzarra
Hector Bujanda