Add configuration 'BUILD_UBOOT_SCRIPTS' to select whether to build the
boot and install scripts or not, and set it to 'true' by default.
This allows removing the scripts on upper Yocto layers.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
All the dualboot logic will be checked in run time.
To do this:
* Include the altboot.src by default in all the images
* Create a post installation script to change the
firmware_download_path in the cloud connector
* Unify the swupdate file descriptor for dual and single boot
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
Increase the timeout from 90 to 120s since it's a large image
and it may take more time on different NANDs.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The U-Boot environment resides on a UBI volume. The uuu script
relies on the environment to save part of the commands that
U-Boot needs to execute after reboot in the middle of the
installation. If the UBI volume 'uboot_config' does not exist
the installer fails.
This commit:
- Creates a function -on the uuu script only- for obtaining
the result of running any U-Boot command (0=success, 1=error).
- Checks the existance of 'uboot_config' volume.
- Runs 'ubivolscript' script to create the UBI volumes layout
that generates the environment volume if it doesn't exist.
- Increases the timeout for running the 'ubivolscript' since
there are occasions in which 'ubi part' (which is part of the
script) takes more time (if it cannot find the fastmap).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
By default ccmp1 platforms have dualboot mode by default, however the required
boot script was added to ccmp15 platform only, so this commit fixes it.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The first time the 'dualboot' variable is tested it is directly run in
the script and doesn't need to escape the special characters.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
When Dual Boot is not enabled, 'rootfsvol' variable must point to the
single boot system rootfs partition 'rootfs'.
Explicitly set this value. Otherwise the script relays on the default
rootfsvol value, which may be a Dual Boot partition.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
- create dualboot.bbclass that
- sets DUALBOOT_ENABLED variable
- defines partition names and function for changing the sw-description
for swupdate
- move files from layer into meta-digi
https://onedigi.atlassian.net/browse/DEL-7962
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
On the CCMP1 SOMs, we only consider a single system partition called UBI,
with many UBI volumes.
The variable 'singlemtdsys' allowed to change between this and
a system with multiple MTD partitions with one UBI volume each
(old approach on CC6UL).
This commit removes the variable and uses the logic as if it was set.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
For the CC6UL 1GB flash variant, the programming of the rootfs exceeds
the current 90 secs timeout, giving following failure:
[Bulk(R):LIBUSB_ERROR_TIMEOUT] fb[-t 90000]: ucmd update rootfs ram ${fastboot_buffer} ${fastboot_bytes} -e
Error: Bulk(R):LIBUSB_ERROR_TIMEOUT
Increase the timeout to prevent the failure.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
As that's an old VM with limited specs, there is no much gain on using
it over the canonical Stash repositories that justifies the code
overhead and the possible errors due to synchronization problems.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
(cherry picked from commit 16eded4f0edcc603de83be7155f7c09718ba5ddd)
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This commit adds u-boot build support for the CCMP15 platform.
The installation scripts are copies from the CC6UL platform.
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
https://onedigi.atlassian.net/browse/DEL-7797
The sign mode needed for each platform is invariable, and since the platform
is already a mandatory parameter for the script, we can store this information
implicitly. Reflect this change in every recipe where the script is used, but
keep the variable at the Yocto level since it's still needed in several places.
https://onedigi.atlassian.net/browse/DEL-7862
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Digi Embedded Yocto 3.2-r2.2
Manually changed recipes to use the master branches instead of the fixed SHA1
from the last release.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
U-Boot uses partition names instead of partition indexes for the nand devices.
This commit syncs the boot scripts with the new dualboot variables.
https://onedigi.atlassian.net/browse/CC6UL-1254
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Add missing call to 'uuu' and erase the partition before creating
the UBI volumes.
Also add larger timeouts to erase operations.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The variable 'dualboot' (and 'singlemtdsys' for CC6UL) was restored
after the bootcmd that runs the first time after programming U-Boot runs
fastboot again to resume the script.
This is ok for the CC6UL but not for the rest of platforms, that run the
partition script on the bootcmd, *before* running fastboot.
Restore the variables for all platforms in the bootcmd right after
resetting the environment.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
U-Boot has embedded support to handle bootcount tries.
When the limit of tries is reached, U-Boot runs the script
in `altbootcmd` rather than the usual `bootcmd`.
This other script resides on meta-digi-dualboot layer.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
Ensure stdout redirection to the USB interface is removed in every case.
Otherwise, it would be left redirected when INSTALL_UBOOT_FILENAME is
manually set.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Install scripts may rework the partition table basing on the value of
env variables. Information of UBI volumes may remain on the NAND that
could later not correspond to the new partition table.
Make sure the MTD partitions are erased prior to updating:
- For Multi-MTD, append '-e' option to the update command.
- For Single-MTD, erase the system partition.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Check the status of 'dualboot' env variable.
If set to "yes", use the dualboot partition table in the script and
restore the variable (default is "no") after resetting the environment.
Also, for dualboot, there's no need to wipe the recovery partition or
boot into recovery mode.
For dualboot, this script programs both systems A and B with the same
images.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-7649
Commit c33fc8a7fe wrongly used
https protocol when using MTK remote when it should have been
ssh.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
When DualBoot mechanism is enabled and an update is pending,
the boot script needs to change certain variables and save the
environment.
The regular boot script already changes a number of variables,
such as 'extra_bootargs' and 'overlays' by appending strings to
the already existing values. Saving the envionment may make these
grow endlessly with each iteration of the boot script.
For this reason, move the DualBoot check as the first thing in
the script, save the environment if needed, and then continue
with the normal flow, that changes variables before booting
but doesn't save them.
On certain scripts, this allows us to get rid of some instructions
for resetting the overlays variable.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The script required the passing of option '-b' for setting up the
target to use a single MTD partition and multiple UBI volumes.
If a target however already has the variable 'ubisysvols' set to
'yes' but this parameter is forgotten when calling the script, the
partition layout would change to default (several MTD partitions).
Remove the recently added '-b' option and make the script decide
basing on the current value of 'ubisysvols' variable.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The script preserves the current value of env variable 'ubisysvols'
so that the new partition script generates the appropriate partition
table before proceeding with the update operations.
If using a UBI volumes layout, the script will not erase the partitions.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-7614
With U-Boot supporting the creation of mtdparts and UBI volumes depending
on the value of variable 'ubisysvols', adapt the install script to make
use of those to generate a partition table and UBI volumes accordingly.
This can be triggered with new option '-b'.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Set the new variable 'rootfsvol' to rootfs_a or rootfs_b when dualboot is
enabled, to cover the case where the devices uses the 'system' partition
with different UBI volumes.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The support for dualboot was integrated on meta-digi-dualboot layer, but it
really depends only on environment variable 'dualboot' so we'd better
integrate the support on the scripts in meta-digi, to avoid synchonization
problems between both layers.
This also allows to be able to easily enable dualboot in U-Boot with the
variable, without needing to update the script on the linux partition.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Enabling DIGI_INTERNAL_GIT defaults to LOG server. The build from local
MTK Digi server was broken.
Fix uboot and linux recipes declaring different repo paths depending on
whether the local remote is LOG or MTK.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
This command was already present on the script used for CC8X. Add it here
so the scripts are as much alike as possible.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Fastboot is configured on boot with the current MMC configuration.
If we create a GPT partition table, we need to restart fastboot before we
try to program any partition with the 'flash' fastboot command.
Set 'fastboot_dev' to a different device, 'sata' for example an back to 'mmc'
to trigger a fastboot restart after creating the partition table on blank
devices.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
The current syntax only works properly when running the script through bash.
Change this so that it works for other shells as well.
While at it, fix a typo in the message that appears when the variant can't be
detected in the 6UL script.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
We document how to use this script from the Yocto image directory. Now that the
*.ext4 files are compressed by default, the script needs to automatically
decompress said files before starting the update process.
https://onedigi.atlassian.net/browse/DEL-7582
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The install script of cc8x had errors (using double '==' instead
of single on comparisions).
Besides fixing this typo, this commit changes the logic to:
- default to 2GB U-Boot for variants other than the ones in the
list.
- consider variant code 0x00 (not programmed HWID) as a failure.
thus forcing the user to specify the file on the command line.
This second action is done also on the cc6ul script.
Reported-by: Hector Bujanda <hector.bujanda@digi.com>
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
install_abort is a temp variable so 'test -n' doesn't work on it.
This was fixed in all scripts except the USB script of ccimx6sbc.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
- Check the existence of files before the 10 second wait.
- Print the list of filenames to program to each partition.
- Print the file that's being updated to each partition.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
With the generalization done in previous commits, we have now several files
that are identical and can be merged into a common SOM or SOM family
folder.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Create global variables:
DEFAULT_IMAGE_NAME
GRAPHICAL_IMAGES
to have them substituted on the U-Boot install scripts for better
generalization.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
U-Boot install scripts (from uSD and USB) were hard-coded to dey-image-qt.
Allow to install other image files by setting a new variable 'image-name'
which defaults to 'dey-image-qt' if not defined, except for the CC6UL
SBC Express, that defaults to 'core-image-base'.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7385https://jira.digi.com/browse/DEL-7333
On these boot scripts, this variable is not used, so we can remove it.
Besides, it's generated by U-Boot code.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Use ##MACHINE## placeholder to have it later substituted by the recipe
using Yocto ${MACHINE} variable.
This will help later reducing the number of files to have one per SOM
(or even family) instead of one per platform.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Otherwise, the name of the file will be "u-boot-dey-initial-env", causing
errors when reading the default environment from userspace, since libubootenv
expects "u-boot-initial-env" instead.
https://onedigi.atlassian.net/browse/DEL-7566
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Non-graphical images (core-image-base, dey-image-aws) don't contain the
graphic-backend on their filenames.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
- Determine first the filenames and abort if any does not exist.
- Print a warning message about the erasing of the media with a list
of partitions and files to use for the update
- Sync the different scripts so they look more similar
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7333
Similar to how it's done on the ccimx6ul, create a function for updating
a partition with a file, that also prints a message.
Rename the function to be the same in all scripts.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7333
Previously, this script only allowed the U-Boot filename as parameter.
This commit makes use of getopts() to pass the following options to the
script:
-h, for help
-i, to pass the dey image name that prefixes the firmware filenames
-n, to skip the 10 seconds delay that allow you to cancel the process
-u, to pass the U-Boot filename
The default image name (if none passed) keeps being 'dey-image-qt' but the
new option allows reusing this script to install dey-image-webkit or
dey-image-aws images.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7385
Since this feature was introduced in newer versions of U-Boot, we need
to disable it for v2017.03 to avoid several compilation issues.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This default environment is needed by packages like libubootenv.
https://jira.digi.com/browse/DEL-7508
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This package has been entirely replaced with libubootenv
https://jira.digi.com/browse/DEL-7410
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This overlay added cooling devices for all quad cores.
On the latest BSP, the SoC device tree include contains all four
cooling devices and the newest U-Boot is able to delete the nodes
for non-existing cores, so there's no need for this overlay
anymore.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Both ConnectCore 8M platforms share the same U-Boot build process,
so apply the same changes for them.
https://jira.digi.com/browse/DEL-7397
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
When manually changing the partition table, it could happen that
a UBI volume already exists in the 'update' partition.
If not erased, the system may find the old UBI volume (with wrong
geometry information) and try to mount it which will result in
failure.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
On commit 1e5cafeb79 a fall-back
update command was introduced in case the newest command fails.
If the newest command succeeds, however, the 'test' command for
error doesn't match (there is no error) and the return code of
such test is "1". On the next check for errors, this results on
an error, when we really mean to continue because the first
command was successful.
Move the second error check inside the error path of the first
attempt.
Reported-by: Francisco Gil <francisco.gilmartinez@digi.com>
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The 'source file system' was removed as an argument from the
'update' command in U-Boot v2020.04.
For platforms using such version, remove it from the update fw
scripts.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DUB-983
A similar change was done in the dey-3.0/maint branch for the uSD installation
scripts, but since USB scripts were added in dey-3.0/master, apply the same
to them as well.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
CC8X SOMs code the RAM size on the OTP bits so this fall-back table
shouldn't be necessary, but update it with latest variants just
in case.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Create scripts to install DEY firmware using a USB stick.
https://jira.digi.com/browse/DEL-6802
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
U-Boot v2020.04 for the CC6UL supports the fastboot protocol.
Create scripts to install DEY firmware via USB using uuu
tool.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Build the U-Boot for variants with 1GB of memory and make the installation and
boot scripts recognize all of the current variants.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Since this overlay is only used in the SBC Pro bootscript, have a separate
bootscript for the SBC Express.
https://jira.digi.com/browse/DEL-7276
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The boot script appends values to certain variables such as
$extra_bootargs and $overlays.
If the final instruction of the boot script (dboot command)
fails, these variables contain the new values, plus the original
one. Since the user recovers the prompt, he may do a 'saveenv'
to save the environment, and the modified variables will be
saved, only to be enlarged again on the next boot.
This can lead to repeated strings on such variables.
Save the original value and restore it in case of failure on
the dboot command.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Follow the syntax:
_ov_<som|board>_<functionality>[_<hardware>].dts
where:
_ov_ identifies the file as an overlay.
som|board identifies whether the overlay applies to the SOM
or to the carrier board.
functionality identifies the function of the overlay.
hardware identifies the hardware to which the overlay
applies.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Wrapping unterminated lines doesn't work for scripts (even
if they contain the backslash).
Substitute with full non-wrapped if/elif sentences.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7252
In the ccimx6sbc, since each SOC has a separate set of device trees, we can use
the soc_family environment variable when generating the name of the final
device tree in the bootscript. However, for the ccimx6qpsbc, there is only one
set of device trees with the "imx6qp" prefix, even though there are SOC
variants such as the imx6dp. Running the bootscript on a ccimx6qpsbc with an
imx6dp SOC assembled will result in a failure, since it will look for a
non-existing device tree starting with a "imx6dp" prefix.
Stop using the soc_family variable and hardcode "imx6qp" instead.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
With the previous solution we would need to generate
multiple overlays for each soc_type, so if we have a
new soc type (for example the solo), we would need
to generate 3 different overlays.
Signed-off-by: Francisco Gil Martinez <francisco.gilmartinez@digi.com>
Add running 'mmc partconf 0 1 1 1' command to the uuu scripts after
writing the new U-Boot into the internal eMMC.
This is required for blank eMMCs on CC8MN and CC8X SOMs where the
'update' command has never been run to be able to boot from eMMC.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
The encryption of the U-Boot environment uses the HWID as key
modifier. The HWID was being read using the fsl_otp driver sysfs
entries and over two words. The driver is now deprecated and also
the cc8x and cc8m platforms have different number of HWID words.
This patch modifies the function that reads the HWID words by
using new entries on the device tree 'digi,hwid_X' where X is the
index of the HWID word.
It also removes the need to select CONFIG_MD5 which is already
auto-selected on sandbox_defconfig by other config switches.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7185
(cherry picked from commit 8ced362766)
The encryption of the U-Boot environment uses the HWID as key
modifier. The HWID was being read using the fsl_otp driver sysfs
entries and over two words. The driver is now deprecated and also
the cc8x and cc8m platforms have different number of HWID words.
This patch modifies the function that reads the HWID words by
using new entries on the device tree 'digi,hwid_X' where X is the
index of the HWID word.
It also removes the need to select CONFIG_MD5 which is already
auto-selected on sandbox_defconfig by other config switches.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-7185
The signing script is used for signing multiple artifacts, not just the
kernel, so rename it for a broader use.
https://jira.digi.com/browse/DEL-7047
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Signing with AHAB mode only requires an additional prior step, so
reuse as much code as possible.
https://jira.digi.com/browse/DEL-7047
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
TRUSTFENCE_SIGN_MODE for ccimx8mn is "HAB", although the
BOOTLOADER_IMAGE_RECIPE is "imx-boot".
https://jira.digi.com/browse/DEL-7024
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
imx-mkimage is a host recipe to provide the mkimage_imx8 binaries, required
for the trustfence support with platform based on AHAB (ccimx8x). Since
these binaries are required to the sign process we need to export it in the
SDK to allow the standalone sign mode, and with that we can simplify the
mechanism to share these binaries with another recipes (u-boot, linux).
Also the do_deploy() from imx-mkimage recipe was removed to avoid overriding
the implementation from the native class and allow populating the mkimage
binaries.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This update is a cosmetic one and removes the RAM frequency from the SCFW
filenames. Reflect this change in the RAM_CONFIGS variable and in the uSD/UUU
installation scripts.
As a result, the imx-boot filenames will no longer have the RAM frequency
either.
https://jira.digi.com/browse/DEL-7096
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The scripts need to know the SOC's revision to be able to select the correct
imx-boot image. Modify the boot-artifacts bbclass so the renamed imx-boot files
are included in the installation .zip.
Also, bypass the SECO fw check in the uSD script so it can install future
versions that aren't recognized by U-Boot's SECO fw checking logic. The UUU
script doesn't require this bypass, since it doesn't use the Digi update
command to flash the bootloader.
https://jira.digi.com/browse/DEL-7069
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
With the device tree overlays mechanism in place, the bootscript
doesn't need to set the fdt_file variable. Instead, it will use
the value it has (which can be changed by the user) and it will
simply update the 'overlays' variable with the device tree
overlays that apply basing on the hardware capabilities found
on the HWID, SOM version, and carrier board version.
This allows a user to override the default fdt_file to point
to his custom device tree, but still make use of the boot script
for hardware-detected overlays.
Without the need to set the base filename, the boot script is the
same for any carrier board of the ccimx8x SOM, so this commit
moves it to a common folder.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Each platform now has only one base device tree, meant for the i.MX8DX variants
of the ccimx8x boards. Apply the QXP overlay in the bootscript if the SOC is
identified as an i.MX8QXP.
Since we want to give this overlay a higher priority than the SOM overlays
(wifi and bluetooth), prepend it to the overlay list after appending the SOM
overlays.
https://jira.digi.com/browse/DEL-7100
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Remove the old wb device trees from the ccimx8x-sbc-express and ccimx8x-sbc-pro
configuration files and add the ccimx8x wifi and bt overlays. Modify both
platforms' bootscripts to apply the overlays depending on board_id, hardware
capabilities or module variants.
https://jira.digi.com/browse/DEL-7100
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The function that parsed the output for a U-Boot variable value
was receiving a multi-line output, with blank lines that were
not being properly processed.
Simplify the parsing by using 'sed' command.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DUB-951
The if condition expanded to nothing so the install command was
never called. Apart from that the install command was wrong and
missing the '-m' option for modifier.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Platform-based variable STORAGE_MEDIA, allows us to select the
correct configuration file without needing to replicate it per
platform.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Parse the hardware version from the HWID and load the overlay if and only if
the revision is "1". Also, update the board's device tree list accordingly.
https://jira.digi.com/browse/DEL-7070
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Instead of having two separate device trees for the non-wireless and wireless
variants of the ccimx8mn, use the non-wireless .dtb as a base and apply the
overlays in the bootscript depending on the variant's capabilities.
Also, update the board's device tree list accordingly.
https://jira.digi.com/browse/DEL-2609
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Update u-boot-fw-utils patches to apply on upstream version 2019.07.
https://jira.digi.com/browse/DEL-7013
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Do not evaluate TRUSTFENCE_SIGN_MODE on conditions where the sign mode
is not relevant:
1) U-Boot binary file should be signed directly after building it when simple
U-Boot images are used, but it should not be signed when imx-boot bundled
images are used.
For those, the signing process is performed later over the whole imx-boot
bundled binary file on a different recipe.
We use BOOTLOADER_IMAGE_RECIPE variable to evaluate this distinction.
BOOTLOADER_IMAGE_RECIPE is set to "u-boot" by default and is set to "imx-boot"
on ccimx8x and ccimx8mn machine configuration files.
2) For signing imx-boot images we should treat differently those images that
include the RAM configuration in their name and those that don't, as we do
for the rest of the tasks in the same recipe. We can ignore the sign mode
method in this case.
https://jira.digi.com/browse/DEL-7023
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
This commit adds a installation script that uses fastboot support to
update the target firmware.
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
https://jira.digi.com/browse/DEL-6845
Digi Embedded Yocto 2.6-r3.1
Manually changed recipes to use the master branches instead of the fixed SHA1
from the last release.
Signed-off-by: Mike Engel <mike.engel@digi.com>
This commit adds some dependencies to include the imx-mkimage package
that is needed to use the mkimage_imx8 tool.
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
* prefix TRUSTFENCE_ to variable SIGN_MODE for DEY
* prefix CONFIG_ to variable SIGN_MODE for script
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Commit 31d8ff94 ("meta-digi-arm: u-boot: Update recipes with new u-boot version")
updates the license checksum for the new u-boot_2019.04 recipe, however this
license file is different for the other u-boot versions.
This commit reverts this change and includes the updated checksum only for the
new u-boot_2019.04 recipe.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Wrapped lines must have a back-slash symbol so that U-Boot
doesn't interpret them as finished.
The missing symbol resulted in the script not being able to
determine the U-Boot image to program in some cases.
Reported-by: Leonid Makhnovskiy <leonid.makhnovskiy@digi.com>
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-6953
Otherwise, users that are behind corporate firewalls might not be able to
obtain the package sources.
https://jira.digi.com/browse/DEL-6663
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The 'soc_type' variable was already set by fastboot to "imx8qxp"
so the U-Boot board code that was setting this to just "8qxp" has
been changed to set it to "imx8qxp".
Update the scripts accordingly.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DUB-901
This commit fixes two issues:
- Comparison clause uses only one equal sign
- Fix soc_type for Dual variants because the supported soc types
for the imx8 processor are: 8qm, 8qxp, and 8dx
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
After the recent changes to generate the bootable artifacts, these are
now formed using the ${MACHINE} variable rather than the string in
${UBOOT_CONFIG} array, so the underscores must be changed with dashes.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Now the U-Boot binaries contain the RAM frequency and bus width, not just
only the RAM size.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-6641
With the arrival of DualX variants, the device tree files have been renamed
to contain the SOC type (8qxp, or 8dx). This is determined by a new U-Boot
variable 'soc_type'.
Default to "8qxp" if the variable is not defined (old U-Boots).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-6641
The new HWID fields make U-Boot create new variable 'module_ram'.
If it exists use it to select the U-Boot file to use during
firmware update. If not, fall back to old method of using the
variant code and the hard-coded table of variants.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-6598
The new HWID fields make U-Boot create new variable 'module_ram'.
If it exists calculate new HWID fields to check if the SOM has
Wi-Fi, Bluetooth, etc. in order to select the device tree file.
If not, fall back to old method of using the variant code and
the hard-coded table of variants.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://jira.digi.com/browse/DEL-6598
Digi Embedded Yocto 2.6-r1.3
Manually changed recipes to use the master branches instead of the fixed SHA1
from the last release.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This variant is exactly the same as variant 0x02, but with a new revision
of the i.MX6UL silicon.
https://jira.digi.com/browse/DEL-6555
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Update u-boot-fw-utils patches to apply on current upstream version. Remove
recipe for version 2017.09 since both U-Boot v2017.03 and v2018.03 work fine
with the newer version.
https://jira.digi.com/browse/DUB-881
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
This adds support for U-Boot v2018.03 for CC8X platforms only.
Create 'digi-u-boot.inc' with the common definitions for both v2017.03
and v2018.03.
https://jira.digi.com/browse/DUB-881
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Fix write operation by moving the re-lock of the mmc partition
after performing the system synchronization, if not the mmc
driver throws read-only errors. Also, improved the code
to avoid compilation warnings because the return values were
not managed in write operations.
https://jira.digi.com/browse/DEL-6449
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Device tree file names won't have the kernel image type like a
prefix anymore, since thud uses the original file names.
https://jira.digi.com/browse/DEL-6443
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Digi Embedded Yocto 2.4-r2.2
Manually changed recipes to use the master branches instead of the fixed SHA1
from the last release.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Javier Viguera
Arturo Buzarra
Gonzalo Ruiz
Francisco Gil
Hector Palacios
Isaac Hermida
Mike Engel
Gabriel Valcazar
Hector Bujanda