Some settings were incorrectly set. Align the card settings with the
same values used in our other platforms.
https://onedigi.atlassian.net/browse/DEL-8703
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
Based on the environment variable emulate-cc91:
* Limit the ram memory to 512MB
* Enable the overlay _ov_som_emulate-ccimx91_ccimx93.dtbo
* Disable the npu node
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
Both CC93 and CCMP2 store the environment at the end of BOOT1 partition
and the redundant environment at the end of BOOT2 partition. Reuse the
'fw_env.config' file defined for CC93 for both platforms, and also include
CC91 in the process.
https://onedigi.atlassian.net/browse/DEL-9119
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
In CCMP2 the HWID is stored in 3 consecutive fuse words, now the third word has
the following scheme:
| 31..18 | 17 | 16 |15..12| 11..7 |6..3| 2..0 |
+--------+----+-------+------+---------+----+------+
| -- | BT | Wi-Fi | RAM | Variant | HV | Cert |
+--------+----+-------+------+---------+----+------+
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The main recipe already contains this file on the SRC_URI.
No need to append for every platform.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Add initial support cloned from ccmp15, based on v2022.10 from STM release
openstlinux-6.1-yocto-mickledore-mp2-v23.12.06.
https://onedigi.atlassian.net/browse/DEL-8995
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commits adds the CCMX91 platform to the DEY
build system. Furthermore, it creates generic ccimx9
support to be used for the CCiMX91 and CCiMX93
platform.
https://onedigi.atlassian.net/browse/DEL-9106
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
When running the installation script on variants with larger NANDs, two of the
script's commands take longer than our intended timeouts under specific
circumstances:
* When the variant has a NAND with 512 MiB or more and singlemtdsys is set
to "yes", running ubivolscipt takes longer than our 10 second timeout.
The larger the NAND storage size, the longer this command takes.
* When the variant has a 1 GiB NAND, singlemtdsys is set to "yes" and
dualboot is set to "no", the update of the recovery UBI volume takes
longer than our 15 second timeout.
In both of these cases, the script fails and the installation process cannot
continue. Apply the following changes to prevent this:
* Increase the ubivolscript timeout from 10 seconds to 30
* Increase the recovery update timeout from 15 seconds to 20
Also, remove the command immediately before ubivolscript is run, since said
command is already being run at the beginning of ubivolscript.
https://onedigi.atlassian.net/browse/DEL-9097
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
One of the conditions used to determine the U-Boot file was missing its
terminator, breaking the script.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
(cherry picked from commit 26dc437a25)
On devices with NAND as storage media, a post install script
modifies the fw_env.config file basing on the NAND geometry.
This only happens once after deployment, typically on production
environments. If the power is removed soon after the post install
script runs (which is a normal procedure on manufacturing
environments), there are chances that pending file system
operations have not been flushed, which may occasionally lead
to the fw_env.config file end up empty on the next reboot.
This commit adds a sync at the end of the post-install script
to guarantee the changes are written to the file system.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-9059
There is a corner case that wasn't cover by the script, if you
use the script using a -k -t the "-t" would be the name of the
dek.bin.
This new implementation solves the issue.
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
By default is trying to install an artifact imx-boot--<platform>
if trustfence is not enabled.
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
Some variables in the script belong to u-boot, not to the shell
running the script. Escape those variables so the shell does not
expand them.
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
The command trustfence update doesn't require the partition argument.
Besides of that, remove extra fi on the cc8m platforms.
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
* Move Digi code out of the upstream files to minimize conflicts in
version migrations.
* Remove all the TEE client copied code and use the libteeclient library.
* Some fixes in the Optee-based environment encryption
* Some simplifications in CAAM-based environment encryption.
https://onedigi.atlassian.net/browse/DUB-1079
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
At the moment, this overlay adds RTC calibration to compensate
the drift observed in the 32kHz input frequency of hardware
version 1 of the SOM.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-8987
Update BDF file used on CC8MN and CC8MM with a new calibration
(GOLDEN3) to obtain a flatter frequency response and a better EVM
performance.
Reference calibration file is obtained from 'qca6574au-le-2-2-2_qca_oem'
repo at tag 'r00005.1' under path
'wlanfw/cnss_proc/wlan/fw/target/sdio_dst/qc6174/bdwlan30.bin'
(MD5SUM: 8a40d95698825e1718bee640b1f7982a).
Target output powers tables and CTL tables remain intact.
Changes required to pass the EN 300 328 V2.2.2 blocking test also remain
intact.
New BDF file:
- bdwlan30_US.bin (86180198440e6ab53734aabf0112c6ba)
https://onedigi.atlassian.net/browse/DEL-9001
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
This commit fixes u-boot Trustfence naming for signed and
encrypted images used in the installation script removing
the a duplicated dash in the u-boot name.
https://onedigi.atlassian.net/browse/DEL-8271
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
Add a check on the existence of the "temp-fitimg-loaded" environment
variable before setting it. It is needed, as with encrypted FIT images,
we need to decrypt them before accessing the boot script. In such cases,
u-boot sets that variable to "no" so the boot script does not override it,
and the FIT image is loaded again before the final boot to the OS.
https://onedigi.atlassian.net/browse/DEL-8945
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
The signing tools have a dependency of libQt5Core.so.5, which implies that this
library must to be installed on the native PC. This commit includes all the
required shared libraries for the signing tools inside the own package to avoid
external dependencies. With this change there is not needed any more the qtbase
dependency at build time.
Package version has been bumped to 1.2.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
- For Qualcomm QCA65x4 platforms:
Add support to create the 'World' board data file for the QCA65x4 Wi-Fi
chip to operate on World regulatory domain.
Kernel wireless driver already supports selecting the correct file based
on the configured Regulatory Domain via Kernel command line argument
'wlan.regdmn', which allows the following parameters:
* "US", for U.S.A. (default)
* "World", for worldwide
- For Murata type2AE platforms:
Add World CLM blob file for the wireless interface and JRL hcd file for
the Bluetooth interface. Also add the autocountry ininitialization script
and systemd service.
World CLM blob file:
- cyfmac4373-sdio_World.clm_blob (1abe7f3fa86d4123b0586cbbf0ec91ac)
Kernel wireless and bluetooth drivers already support selecting the correct
files based on the configured Regulatory Domain via Kernel command line
arguments 'brcmfmac.regdmn' and 'btbcm.regdmn' respectively, which allow the
following parameters:
'brcmfmac.regdmn':
* "US", for U.S.A. (default)
* "World", for worldwide
'btbcm.regdmn':
* "FCC.CE", for U.S.A., Europe and the rest of the world (default)
* "JRL", for Japan
https://onedigi.atlassian.net/browse/DEL-8905
Co-authored-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Different mechanisms are used to sign FIT images on the ccmp1 platforms and the
ccimx93, and we manage each mechanism via a different variable. The variable
names don't really reflect which platform they affect, which makes maintenance
harder.
Rename the variables so that it's easier to identify the platforms/vendors they
affect:
* Replace TRUSTFENCE_FIT_IMG with TRUSTFENCE_SIGN_FIT_STM
* Replace TRUSTFENCE_SIGN_FIT_ARTIFACT with TRUSTFENCE_SIGN_FIT_NXP
Don't rename TRUSTFENCE_FIT_IMG_SIGN_KEYNAME
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Unless we have a use case in which we need to apply these fragments separately,
we can merge them both into a single fragment.
https://onedigi.atlassian.net/browse/DEL-8946
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This logic was fixed in commit e915a14b4b, so we
no longer have to manually copy the bootscript to generate FIT images.
https://onedigi.atlassian.net/browse/DEL-8946
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
We rely on FIT support to implement boot artifact authentication on ccmp1
platforms, but our implementation made it impossible to enable FIT support
outside of the context of Trustfence/secure boot.
Change this so that it's possible to enable FIT support without having to sign
the FIT artifacts. Also, modify the linux-dey 5.15 recipe so that the U-Boot
DTBs with signatures get copied only when FIT signing is enabled.
https://onedigi.atlassian.net/browse/DEL-8946
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit updates the required firmware binaries for Bluetooth and Wireless
interfaces, hostapd and wpa_supplicant recipes based on the Cypress Linux WiFi
Driver (FMAC) release v5.15.58-2023_1128 (Wireless firmware v13.10.246.334).
This change also includes a custom defconfig file for the hostapd and
wpa_supplicant recipes including the changes from the patches and the Digi
customizations.
Also are updated the Murata firmware repositories to match with the latest
Murata release imx-kirkstone-hedorah_r1.0, which is based in the same Cypress
Linux Wifi Driver release v5.15.58-2023_1128.
https://onedigi.atlassian.net/browse/DEL-8667
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The standard string split() function does not support splitting a string
by spaces but preserving quoted strings, so it does not work for build
options disabling functionality, as they have this format:
"# CONFIG_OPTION is not set"
On the other hand, the "shlex" module provides a split function that
allows splitting strings by spaces and, at the same time, preserves
quoted strings.
In Trustfence, we need this functionality to disable default options that
would allow the booting of non-authenticated images.
https://onedigi.atlassian.net/browse/DEL-8704
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Other recipes may access SYSROOT_DIRS content by adding a dependence
on do_populate_sysroot.
We need this specific directory for the kernel fitImage support.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This update fixes an initialization issue with devices without HWID programmed.
https://onedigi.atlassian.net/browse/DUB-1066
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit fixes a build issue when this script is installed but not shipped
in the u-boot-tools package.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Not only install the US but all the FW files.
Apart of that, some scripts need a little adjustement such as:
* Modify the BT baudrate to 3Mbps for EU power configuration, as it is the
baudrate used by the btnxpuart driver.
* Replace the way to reset the interface on each hcitool command to
avoid missleading BT behaviour.
https://onedigi.atlassian.net/browse/DEL-8458
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
This commit implements the support to sign the different memory configurations for
the CCMP1 platforms, when trustfence is enabled, using FIT images.
https://onedigi.atlassian.net/browse/DEL-8752
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit implements the support to allow different memory configurations for
the CCMP1 platforms, adding support to 512MB and 1GB memory variants for the CCMP15.
https://onedigi.atlassian.net/browse/DEL-8752
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Command 'bootz' allows boot unsigned Linux zImages, so disable it when secure
boot is enabled using FIT images.
https://onedigi.atlassian.net/browse/DEL-8769
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Replace the US-only default CLM blob with the latest one, generated by
Infineon based on the results from Digi Certification of the CCMP1.
New file:
- cyfmac4373-sdio_US.clm_blob (92225a8bccf0c7c9d7df6cdd64670fa1)
https://onedigi.atlassian.net/browse/DEL-8598
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Some minor fixes:
* return error code if installation fails
* cosmetic: update comment with options
* just exit after error and do not execute boolimit command
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
Murata provides this FW recipe for the infineon chip on the ccmpx products.
Now we are going to have more FW provided by Murata, but for other chips
which recipe is completely different.
Therefore, rename the recipe to explicitily indicate the FW it provides.
https://onedigi.atlassian.net/browse/DEL-8458
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
Up until recently, we were only generating dey-image-qt images for the
ccimx93-dvk. Now that we are generating dey-image-lvgl images as well, make
sure to print the helper message to set image-name when installing said images.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
One of the conditions used to determine the U-Boot file was missing its
terminator, breaking the script.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
New AR6233 chips from Qualcomm require a power reduction in the 2.4GHz
band to maintain a good EVM.
Generate new board data files with this optimized target power
configuration, but do not replace the original board data files so this
change does not affect CC6 modules with the original AR6233 chip.
The new AR6233 will be populated in modules with Hardware Version=6 or
higher. Load one board data file or the other based on the Hardware
Version field of the HWID via a post-installation script.
Board data files with optimized TX Power ('b' files):
- Digi_6203-6233-US_b.bin (MD5SUM: 53db0fba1eea22d5c7248b35669234bd)
- Digi_6203-6233-World_b.bin (MD5SUM: 307ea9e9364c46a243a36124c92cddc2)
- Digi_6203_2_ANT-US_b.bin (MD5SUM: 741f69584f43258ec15bfccaebdb8896)
- Digi_6203_2_ANT-World_b.bin (MD5SUM: 9f89d081aaef7f26292d42ad193c188d)
https://onedigi.atlassian.net/browse/DEL-8851
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
An additional line was added to a comment block without the '#' character,
resulting in the following error when running the script:
Unknown command '-' - try 'help'
Nonetheless, this error is harmless and the script continues as expected, which
is the reason why we hadn't found it until now.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
In case a HWID is not set or the variant is unknown, do not set it to a default
U-Boot file but ask the user for the proper file.
This case should not happen, but cover it for safety.
https://onedigi.atlassian.net/browse/DEL-8855
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
libubootenv treats negative offsets as backwards offset from the end of
the block device, so use that to move the environment to the last 16KiB
of the hardware boot partitions.
https://onedigi.atlassian.net/browse/DUB-1064
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
With the update of the ethos-u firmware for the NPU in previous commit,
this overlay is no longer required.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
The LEGACY_IMAGE_FORMAT defaults to 'y' if there is no FIT
support, which happens after applying the default configuration.
Then, the FIT support is added in a config fragment, but the
LEGACY_IMAGE_FORMAT is not disabled.
Disabling this is recommended to avoid the possibility to boot
unsigned legacy images.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The U-Boot bootscript loads the fitImage into RAM memory to run
this bootscript. This bootscript ends up calling 'dboot' command
to run the FIT default configuration.
To avoid 'dboot' re-loading again the fitImage into RAM memory,
set this temporary variable that will be immediately reset
by 'dboot'.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
This commit adds several overlays for DVK v2 and modifies the boot script to apply it
based on the board_version variable.
https://onedigi.atlassian.net/browse/DEL-8746
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit adds signed FIT image support for the CCMP1
platforms when using Trustfence.
https://onedigi.atlassian.net/browse/DEL-8591
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
During firmware install, the target may be reset several times.
We don't want the bootcount to count these as boot attempts.
This was done in a791bb4463 for the ccmp1
but not for the rest of platforms.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
(cherry picked from commit 961acf48de)
Improve boot attempts message showing not only the current boot attempt
but also the limit:
(boot attempt 1/3)
Print the message only when the bootcount mechanism is active, i.e. when
the bootlimit is defined (not zero), and when bootcount is > 0.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DUB-1056
(cherry picked from commit 918a9caf1d)
Use the intention of installing dual boot firmware as a condition to set
bootlimit=3 so that the bootcount mechanism is enabled.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DUB-1058
During firmware install, the target may be reset several times.
We don't want the bootcount to count these as boot attempts.
This was done in a791bb4463 for the ccmp1
but not for the rest of platforms.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Improve boot attempts message showing not only the current boot attempt
but also the limit:
(boot attempt 1/3)
Print the message only when the bootcount mechanism is active, i.e. when
the bootlimit is defined (not zero), and when bootcount is > 0.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DUB-1056
The STM signtools are precompiled binaries with a fixed RPATH to look for
dynamic libraries.
When the binaries are installed to the regular ${bindir} (either native or
nativesdk), additional toolchain libraries in the regular ${libdir} folder
confuse the binaries, resulting in segmentation faults when running them
or missing symbols.
The package has been reworked to place the directory structure expected
by the binaries, in a subfolder "stm" within the ${bindir}.
Two wrapper scripts with the names of the binaries (STM32MP_KeyGen_CLI and
STM32MP_SigningTool_CLI) have been created to run the binaries in the new
subfolder.
Package version has been bumped to 1.1.
While on it, remove the 'do_install' from trustfence-stm-signtools.inc
which is not needed because the 'bin_package' class already provides the
same functionality.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-8720
The STM signtools are precompiled binaries with a fixed RPATH to look for
dynamic libraries.
When the binaries are installed to the regular ${bindir} (either native or
nativesdk), additional toolchain libraries in the regular ${libdir} folder
confuse the binaries, resulting in segmentation faults when running them
or missing symbols.
The package has been reworked to place the directory structure expected
by the binaries, in a subfolder "stm" within the ${bindir}.
Two wrapper scripts with the names of the binaries (STM32MP_KeyGen_CLI and
STM32MP_SigningTool_CLI) have been created to run the binaries in the new
subfolder.
Package version has been bumped to 1.1.
While on it, remove the 'do_install' from trustfence-stm-signtools.inc
which is not needed because the 'bin_package' class already provides the
same functionality.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-8720
Some platforms do not support signing external artifacts (kernel, dtb,
etc.) yet, so we need to decouple the signing of the bootloader from the
signing of the external artifacts.
This commit generalizes the code, so instead of having platform exceptions
scattered along the recipes, we create a new variable used conditionally
to sign or not the external artifacts.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This version supports i.MX8ULP and i.MX9x devices.
NOTICE: changed the "srk_ca" parameter in ahab_pki_tree.sh from "yes" to
"no". This script is shared between cc8x and ccimx93. The imx93 does not
support that option at the moment (generation of subordinate SGK certs)
and for the cc8x we were generating them but never used them to sign
the artifacts.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Merge the patches for the PKI tree generation scripts, to ease
maintenance (still keeping two separate patches for HAB4/AHAB).
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
If the default r/w rootfs is not found it will try to do a
fallback to the squashfs image.
In the nand devices additionally we need to set the rootfstype
to squashfs.
https://onedigi.atlassian.net/browse/DEL-8638
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
When booting from a microSD, the variable 'boot_device' is
set to "mmc". Check this to fall back to booting Linux from
the microSD partitions.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Until now, for dualboot systems, all boot variables were calculated on each boot depending on the value of the
'active_system'. These variables are used to boot the device but were not saved, which could lead to a missmatch
between their value in the environment and their required values to correctly boot the system. This commit
simplifies a bit the variables calculation and adds a block to synchronize their value in the environment.
Signed-off-by: David Escalona <david.escalona@digi.com>
All the 'altboot' script functionality has been moved directly to the 'altbootcmd' command
in U-Boot, so this script is no longer necessary. Remove it for all platforms.
https://onedigi.atlassian.net/browse/DEL-8674
Signed-off-by: David Escalona <david.escalona@digi.com>
The install scripts from SD/USB use a fixed image name.
If you are trying to install a different image you need to set
the env variable 'image-name' first.
Add a helper message if default files are not found to
avoid needing to go to the documentation.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
During firmware install, the target may be reset several times.
We don't want the bootcount to count these as boot attempts.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The 'bootcount' value is now incremented and stored in the system on every boot and
not only then the 'upgrade_available' flag is set. Also, ensure the value is cleared
when the 'altboot' script is executed by running the new U-Boot command 'bootcount reset'.
https://onedigi.atlassian.net/browse/DEL-8506
Signed-off-by: David Escalona <david.escalona@digi.com>
When TrustFence is enabled, a PKI tree is generated.
In the case of NXP platforms, the PKI contains public certificates
from which the public key needs to be extracted using an openssl
command.
In the case of STM platforms, the PKI contains directly the
public key.
In all cases, we need the public key to be installed in the
rootfs /etc/ssl/certs/ folder, so that it can be used by
swupdate to authenticate signed SWU packages.
Up to now, this was being done on the dualboot recipe, but the
installation of the public key should really be only dependant
on the fact of TF being enabled.
This commit:
- Removes the generation of the public key from dualboot.bb.
- Generates a patch to extract the public key from the certificate
as part of the PKI tree generation (on NXP platforms).
- Installs the public key during a post install function after
the final rootfs has been created.
- For NXP platforms, extracts the public key using openssl if
it does not exist (for backwards compatibility).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
When booting from recovery sdcard, in the imx93 the dualboot is yes by
default, so the mmcroot variable was not set correctly for the uSD.
If we boot from uSD, just assume all the system is in the uSD card, whether
it is a recovery system or a prepared uSD card for demo.
https://onedigi.atlassian.net/browse/DEL-8461
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
Starting at kernel 6.1, the maxim98088 driver has been migrated
from the old imx-max98088.c driver to NXP’s new audio framework
fsl-asoc-card.c.
Update the sound stuff to match the new audio card and some of
the new controls.
https://onedigi.atlassian.net/browse/DEL-8596
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
This includes NXP's code from the SCFW porting kit v1.15.0, support for
variants with 4 GiB of RAM and a fix for an issue when resuming from suspend.
https://onedigi.atlassian.net/browse/DEL-8604
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit adds support for environment encryption/decryption of the
u-boot environment on the CCMP1 platform in Linux.
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
Regulatory domain is now provided as a Kernel parameter, and the
wlan driver uses it to select the correct BDF file, so we don't
need to change the symbolic links to point to one file or another
anymore.
https://onedigi.atlassian.net/browse/DEL-8360
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
We can't run a post installation script in a readonly file system.
We need to provide a configuration file beforehand.
https://onedigi.atlassian.net/browse/DEL-8556
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
We no longer need logic to determine the SOM's RAM size and bus width, we only
need to know the SOC revision, which is info that is always available.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Now that both U-Boot and the SCFW can autodetect the RAM configuration, we can
simplify the imx-boot build process to generate two binaries (one per SOC
revision) instead of eight. Build "flash_spl" imx-boot images and use only one
global defconfig for u-boot.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This update includes automatic RAM configuration detection, and only one SCFW
binary is needed for all ccimx8x variants. Adapt the imx-boot recipe
accordingly.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
For the ccimx8x, we changed the order of the steps in do_deploy() from:
Deploy -> Rename files -> Move binaries
To:
Deploy -> Move binaries -> Rename files
When it's time to rename the files, they won't be in their original place and
the process will fail. Make sure we move the files after they've been renamed
to avoid errors.
Also, one move operation is enough for all artifacts, so remove the second
operation.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
There are two different firmware files for Bluetooth on Murata's type2AE
module:
- JRL: It configures a Bluetooth TxPower of 7dB, to be used in Japan
only.
- FCC.CE: It configures a Bluetooth TxPower of 5dB, to be used in the
rest of the world.
To comply with the FCC requirement that it should not be possible to
configure different regulatory domains, or in this case configurations,
than FCC, only deploy the FCC.CE file by default:
- BCM4373A0_FCC.CE.hcd (md5sum: 1e287a3ab7f83e59352cb321315ea80f)
This file reports the following information during boot time:
Bluetooth: hci0: 89373 UART 37.4 MHz wlbga_BU sLNA muRata Type 2EA 5dBm 20220608-0103
Bluetooth: hci0: BCM4373A0 (001.001.025) build 0155
JRL file will be added via the Worldwide DEY patch addon that customers
can request from Digi.
https://onedigi.atlassian.net/browse/DEL-8453
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Replace the CLM blob file from Github, which supports several countries
with a custom US-only CLM blob file. This way, default images will only
have support for US regulatory domain, therefore complying with FCC
requirements.
The Worldwide CLM blob file will be provided by Digi International on
request.
https://onedigi.atlassian.net/browse/DEL-8453
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
We can't run a post installation script in a readonly file system.
We need to provide a configuration file beforehand.
https://onedigi.atlassian.net/browse/DEL-8556
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
This commit modifies the boot script condition to apply the overlay for MCA
based on HWID MCA field.
https://onedigi.atlassian.net/browse/DEL-8521
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The tools STM32MP_KeyGen_CLI and STM32MP_SigningTool_CLI have
a dependency of libQt5Core.so.5 which is provided by qtbase.
Add this dependency to avoid errors during SDK generation.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
For the moment, do not sign aditional artifacts, such as the ramdisk,
the kernel or the boot scripts for STM platforms.
In the specific case of the ramdisk, simply copy it over with the
expected filename extension.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The do_deploy:append did three things:
- adapt the U-Boot filenames to 'u-boot-<platform>-<config>.<ext>'
- sign/encrypt the U-Boot files (only for iMX6 family)
- sign the boot scripts
Convert the first two actions into functions (the third already was) and
call them conditionally as postfuncs.
Also skip the signing of U-Boot files if the platform is not based on
iMX6 family.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Certain platforms share a processor family but need to be differentiated
between them. DEY was using the variable DIGI_FAMILY as the SOM name
rather than the family. It becomes useful to have both (DIGI_SOM as the
more specific, and DIGI_FAMILY as the more generic).
This is the case, for example, of:
- ccmp1 (family)
- ccmp15 (SOM)
- ccmp13 (SOM)
- ccimx8m (family)
- ccimx8mm (SOM)
- ccimx8mn (SOM)
Both variables are used on the machine overrides.
Where DIGI_FAMILY was used, use now DIGI_SOM.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
This recipe downloads a tarball that contains the binaries:
- STM32MP_KeyGen_CLI
- STM32MP_SigningTool_CLI
from ST Microelectronics STM32CubeProgrammer v2.12.0.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The name of the variable was not very intuitive of what
it contains. This variable expands to the SoC vendor
(NXP or STM).
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Commit 065cf3e9 ("kirkstone migration: general update to the new override
syntax") incorrectly renamed binaries in a massive change. This commit restores
the binary names to the original.
https://onedigi.atlassian.net/browse/DEL-8478
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
These are recipes we created to support Google Coral on i.MX platforms. ST's
machine learning layer provides similar recipes, so to avoid conflicts, move
the recipes meant for i.MX platforms to a dynamic layer.
https://onedigi.atlassian.net/browse/DEL-8308
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The HWID is populated on the device tree by the boot loader.
This can be used as a key modifier when encrypting the U-Boot
environment. Some old U-Boot versions however, did not populate
the HWID on the device tree. When updating firmware from an
old version to a new one, the library may not be able to read
the HWID from the DT and then be unable to unencrypt the
environment.
This patch implements a fall-back function to read the HWID
directly from the nvmem node (sysfs). Implementation has been
done for ccimx6 family only, where this case of old U-Boot
can happen.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-8444
(cherry picked from commit 222a91f213)
Isaac Hermida
Hector Palacios
Francisco Gil
Arturo Buzarra
Javier Viguera
Gonzalo Ruiz
Mike Engel
Gabriel Valcazar
Hector Bujanda
David Escalona