Device tree overlays now have the extension 'dtso' that
distinguishes them from board 'dts' files, so there is
no need for a prefix '_ov_' to tell if a file contains
a DT overlay.
To make them shorter and easier to tell the platform they
are for, change the filename format to:
<platform-name>_<functionality>.dtso
where <platform-name> can be the name of the SOM or the
name of the DVK, so there is no need either to specify
'som' or 'board' on the filename.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
This recipe extracts a small set of UAPI header files form the linux-imx tree.
However, the revision these headers are extracted from is already present in
our linux fork, so bitbake is currently fetching the linux-imx repo to obtain
some files that it can also obtain from our fork. This is impractical because
the repo in question is quite large (~2.80 GiB) and only getting larger with
time.
By modifying the recipe to use our linux fork instead of NXP's, we avoid having
to fetch NXP's repo.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This doesn't change the behavior of the linux-dey recipe, all it does is make
the LINUX_GIT_URI variable accessible to any meta-digi recipe.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Now all platforms support setting the GPIO name instead of an index
as the configuration for the GPIO-enabled secure console.
Repurpose the TRUSTFENCE_GPIO_ENABLE macro to directly set the GPIO
name.
Also take the opportunity to remove TRUSTFENCE_GPIO_ENABLE and
TRUSTFENCE_CONSOLE_PASSPHRASE_ENABLE commented definitions from bbclass
and conf files, and remove a duplicated TRUSTFENCE_CONSOLE_DISABLE
definition from ccmp1.inc.
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
When ST_OPTEE_DEBUG_TRACE=0, the source code default to a LOG_LEVEL=2
which prints a lot of messages on the boot log.
Reduce it to LOG_LEVEL=1.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
After the rework in 61eb1bfbe6 the metadata
file inside the fip/ subfolder has the default filename 'metadata.bin'.
Use the new symlinks that now live on the deployimgdir.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
These are clones of 'optee-programmer-uart' and
'optee-programmer-usb' defined in tf-a-stm32mp-config.inc but
do not require to have the STM32MP_DEVICETREE_PROGRAMMER_ENABLE=1
which causes build problems in U-Boot.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-9483
bluez5-init is a Digi custom recipe to collect the init script
needed to bring up the specific platform bluetooth hardware.
CCMP1s do not require any bluetooth init extra action.
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
The BT interface initialization is occasionally failing with the hci0
interface not being fully up.
Adding the retry solves all those initialization failures.
https://onedigi.atlassian.net/browse/DEL-9287
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
This avoids the next warning when builing for STM platforms
WARNING: No recipes in default available for:
meta-digi/meta-digi-arm/recipes-kernel/kernel-modules/kernel-module-nxp-wlan_git.bbappend
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
The following TF-A artifacts are deployed to subdirectories of
the image deploydir:
- arm-trusted-firmware/tf-a-<platform>-<bootconfig>.stm32
- arm-trusted-firmware/metadata-<platform>.bin
- fip/fip-<platform>-<bootconfig>.bin
- fip/fip-<platform>-ddr-<bootconfig>.bin
These binaries are not copied to the image deploy dir during
the regular do_deploy(), instead, they are deployed by script
tf_a_sysroot_populate() which is added to SYSROOT_PREPROCESS_FUNCS.
To follow this logic, change the previously wrong do_deploy:append
into a new function and append it also to SYSROOT_PREPROCESS_FUNCS,
so that it is called after the artifacts have really been deployed.
In the existing code, fix the paths and commands, which had some
errors.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-9461
A recent meta-freescale update broke the firmware-ele-imx recipe by setting
a default SECO_FIRWARE_NAME value containing a SoC revision macro we don't
have access to (IMX_SOC_REV_LOWER). Like we do for the ccimx93, use our SoM's
override to overwrite the meta-freescale value with our own.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This override was recently added to meta-freescale's graphical package recipes
to easily distinguish between i.MX platforms that use the Vivante driver and
those that use the Mali one. Without this change, a lot of these recipes are
broken, so sync with the latest changes in meta-freescale's imx-base.inc file.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
We apply a very similar patch to the i.MX fork of weston 12.0.4, but we never
needed this patch for stm32mp platforms because they used to have 10.0.2, which
has wl_shell support. Now that stm32mp platforms use 13.0.1, use the 12.0.4
patch as reference and adapt it so it applies and builds correctly.
This makes it possible to run the LVGL demo on the ccmp25-dvk.
https://onedigi.atlassian.net/browse/DEL-9458
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit adds a patch to the gcnano-driver-stm32mp recipe to address a
Kernel NULL pointer issue that occurs during uncontrolled shutdown sequences.
This issue causes an unexpected Kernel NULL pointer exception, preventing the
system from powering off.
https://onedigi.atlassian.net/browse/DEL-9449
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit increases the maximum rootfs size to 2.5 GB, aligning it with the
default rootfs partition size of 3 GB. This adjustment allows adding all the
functionality required by the user.
https://onedigi.atlassian.net/browse/DEL-9456
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The IW61x, when enabled as AP or P2P (or bridge with AP), generates udev
triggers that lead the wifi card to fail.
Ignore those events.
The reason of this new behavior is due to poky commit 1e8b49999ad8,
"udev-extraconf: fix network.sh script did not configure hotplugged interfaces"
https://onedigi.atlassian.net/browse/DEL-9465
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
We tested all tarball compression formats supported by poky, and although bz2
has faster (de)compression time, xz is better in terms of compression ratio:
for all of the rootfs tarballs generated for our currently supported
images/platforms (15 at the moment), the xz format saves an average of 30 MiB
per tarball compared to bz2, totalling up to 450 MiB.
No extra dependencies are pulled in, since xz-native is already being pulled in
for all of our image builds, so the only drawback to this change is the
increased compression time (+7.34s on average per tarball).
https://onedigi.atlassian.net/browse/DEL-9459
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
We have these features enabled for our mp1 platforms, and the optee one is
needed in order to pull in the optee-os package to the images/sdk.
https://onedigi.atlassian.net/browse/DEL-9443
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit clears the Cortex-M33 applications list to prevent including all
the Cortex-M33 demo applications from the ST layer. In the future, if we have
custom Digi examples, they should be added here.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
.ext4 files are identical to .ext4.gz, but uncompressed. .tar.xz files are the
exact same as .tar.bz2, but compressed with a different format.
Remove these artifacts to reduce storage overhead and to match the rest of our
platforms.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Both python3-cryptography and python3-pyelftools are needed to compile optee-os
with a Yocto-generated SDK, but we were adding these packages to all i.MX SDKs,
even for platforms that don't use optee. This wouldn't be a problem if it
weren't for the fact that python3-cryptography is implemented in rust, and its
inclusion in the SDKs forces bitbake to generate the rust compiler just for
that package.
Only include these python packages for platforms that use optee.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This replicates meta-imx commit addc08b02f9a, which was added to be able to
re-use packages in i.MX8/i.MX9 builds. Without this change, there are
compilation errors when building recent versions of the onnxruntime package
because some .S files are built with specific -march switches that conflict
with our current tunings. For example, when building for the ccimx8x-sbc-pro:
cc1: error: switch '-mcpu=cortex-a35+crc+crypto' conflicts with '-march=armv8.2-a+fp16' switch [-Werror]
[...]HalfGemmKernelNeon.S:151: Error: selected processor does not support `fmla v20.8h,v16.8h,v0.h[0]'
Using the generic tuning solves this issue, and according to the log in the
original meta-imx commit, this has minimal to no impact on binaries, so use
said tuning in all relevant platforms.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Based on the boot schemes and sources supported for each platform, the boot
artifacts now include this information in their filenames. This commit updates
the filenames accordingly in several recipes.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit updates the required firmware binaries for Bluetooth and Wireless
interfaces and the Murata firmware repositories to match with the latest Murata
release imx-scarthgap-jaculus_r1.0, which is based in the Cypress Linux Wifi
Driver (FMAC) release v6.1.97-2024_1115 (Wireless firmware v28.10.387.10).
https://onedigi.atlassian.net/browse/DEL-9426
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit integrates the necessary changes from the weston-init.bb recipe in
the Poky layer to resolve a rootfs installation issue with the tim-vx-tools
recipe caused by a mismatch in the permissions of the /home/weston folder.
https://onedigi.atlassian.net/browse/DEL-9419
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The value of this variable is always the same within a platform, so it doesn't
make sense to have different variables for it in each recipe that requires it.
While at it, it seems like all currently supported platforms in DEY 5.0 use the
same value of "wayland-1", presumably because they all use similar versions of
wayland/weston. Set this as the default value for all platforms for now. As we
support more platforms, we can adjust this value if needed, but if it ends up
being the same for all platforms, we can just hardcode it.
https://onedigi.atlassian.net/browse/DEL-9404
Co-authored-by: Isaac Hermida <isaac.hermida@digi.com>
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit integrates a custom .bbappend to fix a deployment issue of the
final FIP artifact, where the SoC name does not match with the FIP device tree
name.
https://onedigi.atlassian.net/browse/DEL-9381
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit removes kernel headers from the SDK package list to prevent
overwriting the default ones, as there are currently no ST-specific headers
required.
https://onedigi.atlassian.net/browse/DEL-9381
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit updates the default FIP generation variables to align with the
common stm32mp2 configuration files from the latest meta-st-stm32mp layer,
based on the openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06 tag for Yocto 5.0
(Scarthgap).
https://onedigi.atlassian.net/browse/DEL-9381
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit removes all outdated weston recipes and synchronizes it with the
latest v13.0.1 from the meta-st-openstlinux layer, based on the
openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06 tag for Yocto 5.0 (scarthgap).
https://onedigi.atlassian.net/browse/DEL-9381
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit removes all unnecessary files after the integration of the latest
ST BSP, based on the openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06 tag for
Yocto 5.0 (Scarthgap).
https://onedigi.atlassian.net/browse/DEL-9381
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Update ccmp2 platform to use the latest U-Boot v2023.10 based on the
openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06 tag for Yocto 5.0 (scarthgap).
https://onedigi.atlassian.net/browse/DEL-9381
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Update ccmp2 platform to use the latest Linux kernel v6.6.48 based on the
openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06 tag for Yocto 5.0 (scarthgap).
https://onedigi.atlassian.net/browse/DEL-9381
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit removes the outdated wayland-protocols recipe and synchronizes it
with the latest v1.33 from the meta-st-openstlinux layer, based on the
openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06 tag for Yocto 5.0 (scarthgap).
https://onedigi.atlassian.net/browse/DEL-9381
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit removes all outdated gstreamer recipes and synchronizes it with the
latest v1.22.12 from the meta-st-openstlinux layer, based on the
openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06 tag for Yocto 5.0 (scarthgap).
https://onedigi.atlassian.net/browse/DEL-9381
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit removes the gcnano recipes integrated into meta-digi, as a new
version (v6.4.19) has been released in the latest ST BSP, based on the
openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06 tag for Yocto 5.0 (Scarthgap).
https://onedigi.atlassian.net/browse/DEL-9381
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit removes the scp-firmware recipe, as it has been integrated into the
optee-os recipe with the latest v4.0.0 from the ST BSP release. This update is
based on the openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06 tag for Yocto 5.0
(Scarthgap).
https://onedigi.atlassian.net/browse/DEL-9381
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit removes all outdated OPTEE-OS recipes and synchronizes the Digi custom
.bbappend with the latest v4.0.0 from the ST BSP release, based on the
openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06 tag for Yocto 5.0 (scarthgap).
https://onedigi.atlassian.net/browse/DEL-9381
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit removes all outdated TF-A recipes and synchronizes the Digi custom
.bbappend with the latest v2.10 from the ST BSP release, based on the
openstlinux-6.6-yocto-scarthgap-mpu-v24.11.06 tag for Yocto 5.0 (scarthgap).
https://onedigi.atlassian.net/browse/DEL-9381
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The ccmx91 uses the same AHAB-containerizing command as the ccimx93,
so fix the code to remove the hardcoding check for the ccimx93.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This commit in Poky:
https://git.yoctoproject.org/poky/commit/?id=fbace4111441d36026c3b5cd2ef690250ca8c448
changed the naming/symlinking of the different dtb files installed in
the deploy directory. In Yocto 4.0 we had:
146432 nov 19 14:37 ccimx8x-sbc-pro--5.15-r0.6-ccimx8x-sbc-pro-20241119124717.dtb
61 nov 19 14:37 ccimx8x-sbc-pro-ccimx8x-sbc-pro.dtb -> ccimx8x-sbc-pro--5.15-r0.6-ccimx8x-sbc-pro-20241119124717.dtb
61 nov 19 14:37 ccimx8x-sbc-pro.dtb -> ccimx8x-sbc-pro--5.15-r0.6-ccimx8x-sbc-pro-20241119124717.dtb
while in Yocto 5.0:
19 nov 19 17:57 ccimx8x-sbc-pro--6.6-r0.0-ccimx8x-sbc-pro-20241119164948.dtb -> ccimx8x-sbc-pro.dtb
19 nov 19 17:57 ccimx8x-sbc-pro-ccimx8x-sbc-pro.dtb -> ccimx8x-sbc-pro.dtb
151552 nov 19 17:57 ccimx8x-sbc-pro.dtb
Now, the regular file does not have timestamps or platform name suffixes,
so adjust the signing code to reflect this change.
https://onedigi.atlassian.net/browse/DEL-9325
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This commit changes the audio card name for the
asound configuration and state of the following
platforms:
* CCiMX8X
* CCiMX8M
* CCiMX6UL
https://onedigi.atlassian.net/browse/DEL-9005
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
Now that the tool supports OpenSSL 3.2.3, the same version provided by Yocto
5.0 poky, we can simply use the regular Yocto version of the package and link
to it dynamically instead of building a separate version specific for the tool.
Reflect this change in the recipe and include the new binary "mac_dump" in the
package.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
An internal build of openssl is compiled as part of the cst build process,
which is later linked statically to the tool. When building the nativesdk
version of cst, openssl's internal "Configure" tool chooses Yocto's nativesdk
compiler for its compilation (x86_64-deysdk-linux-gcc). However, cst's Makefile
uses host tools by default, meaning it will compile its C files with the host's
gcc and link the final binary with the host's ld. This can lead to errors due
to the Yocto nativesdk compiler including symbols in the openssl libraries that
are unknown to the host's linker.
For example, when attempting to build nativesdk-trustfence-cst in Yocto 5.0 on
Ubuntu 2020.04, the following linker error appears multiple times:
undefined reference to `__isoc23_strtol'
Fix this by making sure cst uses the same toolchain as the one used when
building the internal openssl libraries (and ultimately, when the final binary
is linked together). This doesn't affect the native version of cst, which uses
the host's toolchain.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Our distribution is Digi Embedded Yocto (DEY), so use that to mark the
upstream status of the patches in our layer.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
The way tagged imx-boot images are handled in meta-freescale was changed in
commit 161f1b3e69a3cf011a50e9b742fb8c46d61e41e8. Reflect this in our recipe by
using the same overrides as uuu_bootloader_tag.bbclass to disable the
functionality
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This variable was removed from the base imx-boot recipe in meta-freescale
commit c30f12b809a8cf36043b42c67dd8a11f69d9cf77, as it was never being
overridden and always had a value of "imx-boot".
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
For some reason, using the '+=' operator instead of ':append' when specifying
the staticdev package's FILES, the original values are overwritten, causing all
of them to get included in the dev package instead. Since some of these files
are static libraries, this causes QA errors.
Replace the '+=' operator with ':append' to fix this.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
In meta-freescale commit 4d64dde1686a017ebe2763dd7880563a6fc51b53,
compile_mx8m() was modified to account for possible configuration suffixes in
the dtb filename via the creation of a symlink. In our case, the filename is
the same as the target, causing the dtb to get replaced with a dead symlink.
For now, revert this function to how it was in the kirkstone branch of
meta-freescale to avoid this.
https://onedigi.atlassian.net/browse/DEL-9011https://onedigi.atlassian.net/browse/DEL-9081
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
By default, wpewebkit now depends on flite, a package that is provided by said
layer. To meet this dependency, all platforms that are capable of running
webkit must include this layer.
https://onedigi.atlassian.net/browse/DEL-9011
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Check that weston-start exists before modifying it: after a recent change in
poky's weston-init recipe, this file only gets installed in non-systemd images.
Remove hardcoded systemd service path: some of the code ported from
meta-st-openstlinux assumes that the original weston-init systemd services are
installed under /lib, and it uses hardcoded paths to detect them. Yocto 5.0 now
has usrmerge enabled, so the services are installed in /usr/lib instead,
causing the check to fail. Replace the hardcoded path with its respective
variable.
https://onedigi.atlassian.net/browse/DEL-9011https://onedigi.atlassian.net/browse/DEL-9045
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
poky has reworked the format of image names, hardcoding the IMAGE_NAME_SUFFIX
(.rootfs) into IMAGE_LINK_NAME, the name used for image symlinks. This would
only be considered a cosmetic change if it weren't for the fact that we have
scripts and test infrastructure that relies on the old image name format, and
this change would force us to rework it all.
Remove the suffix from the link name to maintain our image name format, and
reflect this name in our custom image type scripts. Note that this removes
".rootfs" from several files, for example:
* .rootfs.ext4.gz is now .ext4.gz
* .rootfs.cpio.gz.u-boot.tf is now .cpio.gz.u-boot.tf
* .rootfs.ubifs is now .ubifs
* .rootfs.sdcard is now .sdcard
However, symlink names and non-rootfs files (.boot.vfat, .recovery.vfat...)
are unchanged.
https://onedigi.atlassian.net/browse/DEL-9011
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
poky commit 56fe6d575e184ed44807fe27e069233da36962ad removed the BSD license in
favor of using more specific ones. Replace BSD in the dtc recipe with the
correct one, which is BSD-2-Clause
https://onedigi.atlassian.net/browse/DEL-9011
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Our do_install() places all firmware files inside of the path in the
{base_libdir} variable, but we were hardcoding /lib in FILES. This is an issue
when using the usrmerge distro feature, because {base_libdir} becomes /usr/lib
instead of /lib. This was causing these recipes to fail.
Fix this by using {base_libdir} in FILES so that it matches do_install().
https://onedigi.atlassian.net/browse/DEL-9011
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
These recipes install binaries inside of /sbin, which causes QA errors when
usrmerge is enabled in DISTRO_FEATURES. Said feature is now required for
Yocto 5.0's version of systemd, so keep using the same versions of the tools
and simply move the binaries to /usr/sbin if needed.
https://onedigi.atlassian.net/browse/DEL-9011
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This variable now has a weak assignment in poky with the default value
"sysvinit", which was overriding our weak assignments.
https://onedigi.atlassian.net/browse/DEL-9011
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
These patches were originally backported from U-Boot v2023.07, and now that
u-boot-tools is using v2024.01, they are no longer needed
https://onedigi.atlassian.net/browse/DEL-9011
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Remove ccimx9-specific versions from the ccimx9 machine file and use the same
package versions for all platforms, except where noted explicitly in
imx-base.inc. Also, reflect the latest ported changes from meta-imx.
https://onedigi.atlassian.net/browse/DEL-9011https://onedigi.atlassian.net/browse/DEL-9081
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Since our recipes handle native builds differently, port the latest version
of the recipes from meta-freescale to our layer while keeping our
customizations. Use the same revision for all platforms.
Adapt patches for lf-6.6.23-2.0.0 release and add the "Upstream-Status" tag to
them to avoid QA errors.
For now, use the imx-boot recipe from meta-freescale, but there's a chance we
might need to port the version of the recipe in meta-imx.
https://onedigi.atlassian.net/browse/DEL-9011https://onedigi.atlassian.net/browse/DEL-9081
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The recipe for 4.2.0.imx has been upstreamed, so merge both of our .bb files
for 4.0.0.imx and 4.2.0.imx into a single .bbappend file. Adapt our patches to
support the ccimx93 and ccimx91, and while at it, add the "Upstream-Status"
tag to them to avoid QA errors
https://onedigi.atlassian.net/browse/DEL-9011https://onedigi.atlassian.net/browse/DEL-9081
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Back in Yocto 4.0, we applied some imx recipe changes exclusively for the
ccimx93 from meta-imx's rel_imx_6.1.55_2.2.0 tag, but now these changes have
been upstreamed in the meta-freescale scarthgap branch. Since there currently
isn't an NXP BSP based on scarthgap, make all platforms use the upstreamed
versions of the recipes, which are the same versions or newer as the ones
available in meta-imx
Remove the recipes for:
* firmware-ele-imx
* gstreamer1.0-plugins-bad
* gstreamer1.0-plugins-base
* gstreamer1.0-plugins-good
* gstreamer1.0-plugins-good
* gstreamer1.0-plugins-ugly
* gstreamer1.0
* imx-atf
* imx-boot-firmware-files
* imx-codec
* imx-g2d-samples
* imx-m33-demos
* imx-m4-demos
* imx-m7-demos
* imx-parser
* imx-pxp-g2d
* libdrm
* linux-imx-headers
* optee-test
* wayland
* wayland-protocols
* weston
* xwayland
Apply these changes:
* Remove ccimx93-exclusive changes in gstreamer1.0-meta-base
* Modify imx-gst1.0-plugin bbappend so the upstream version is used in all
platforms
* Remove imx-alsa-plugins bbappend so the upstream version is used in all
platforms
* Remove firmware-nxp-wifi bbappend since the files we need to install seem
to already be included in the meta-freescale recipe
* Remove imx-test and imx-lib bbappends since our custom changes have
already been included in the meta-freescale recipes
https://onedigi.atlassian.net/browse/DEL-9011https://onedigi.atlassian.net/browse/DEL-9081
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
* meta-ml was renamed to meta-imx-ml, and its BBFILE_COLLECTIONS was renamed to
imx-machine-learning
* meta-st-stm32mpu-ai was renamed to meta-st-x-linux-ai
https://onedigi.atlassian.net/browse/DEL-9011
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Starting in poky commit 8791c77a4098d62080ecad09d94718eccd7f1a47, there is
now a check to make sure TEMPLATECONF follows specific rules. If we don't abide
by them, an error will occur when creating a project with our mkproject.sh
script. Move the templates to the place they're supposed to be in and reflect
the change in mkproject.sh.
https://onedigi.atlassian.net/browse/DEL-9011
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The SCP firmware introduces too much verbosity (with
timestamp included) in the middle of the boot log
between the TF-A and U-Boot.
Reduce the log and remove compiler flags for errors
on unused variables (banner strings).
This removes the following messages from SCP firmware:
[ 0.000000] SCP-firmware v2.12.0-dev
[ 0.000000]
[ 0.000000] [FWK] Module initialization complete!
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
ST_OPTEE_DEBUG_TRACE is set to 0 if ST_DEBUG_TRACE is set to 0.
However, on the optee source code, if ST_OPTEE_DEBUG_TRACE=0 the
log level is automatically set to 3 (INFO) resulting in a very
verbose optee log.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
The ccimx91 is a headless platform. Disabling those distro features
prevents building/installing packages that are useless (e.g. gstreamer)
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This commit changes the linux and recovery UUID when booting
the system in single mode.
https://onedigi.atlassian.net/browse/DEL-9244
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
Some settings were incorrectly set. Align the card settings with the
same values used in our other platforms.
https://onedigi.atlassian.net/browse/DEL-8703
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
These are files for programming images with STM32CubeProgrammer tool. We don't
use the tool or the files. Disable the task to avoid build warnings, just like
we do for the ccmp1 platforms.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Instead of manually disabling the task, use the ENABLE_FLASHLAYOUT_CONFIG
variable which is meant for that exact purpose.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This removes the psplash package from "core-image" images, which
prevents this failure onn boot:
[FAILED] Failed to start Start psplash boot splash screen.
psplash[454]: Error opening /dev/fb0
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Based on the environment variable emulate-cc91:
* Limit the ram memory to 512MB
* Enable the overlay _ov_som_emulate-ccimx91_ccimx93.dtbo
* Disable the npu node
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
This commit adds the initramfs into the FIT recovery
image. If the RAM disk image is included in the FIT
image we need to create a initramfs file that doesn't
include the u-boot header, because the FIT descriptor
contains all the necessary information to use the
initramfs file.
https://onedigi.atlassian.net/browse/DEL-9168
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
When EXTRA_IMAGE_FEATURES += "overlayfs-etc" is added these
configurations are needed to compile. They are provided with
the default configuration to work with our software.
https://onedigi.atlassian.net/browse/DEL-9186
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
DEY generates the ccmp25 boot artifacts on subdirectories of the main
deploy folder. The firmware installation script expects to have them on
the deploy directory, so create the proper symlinks.
https://onedigi.atlassian.net/browse/DEL-9120
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Both CC93 and CCMP2 store the environment at the end of BOOT1 partition
and the redundant environment at the end of BOOT2 partition. Reuse the
'fw_env.config' file defined for CC93 for both platforms, and also include
CC91 in the process.
https://onedigi.atlassian.net/browse/DEL-9119
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
In CCMP2 the HWID is stored in 3 consecutive fuse words, now the third word has
the following scheme:
| 31..18 | 17 | 16 |15..12| 11..7 |6..3| 2..0 |
+--------+----+-------+------+---------+----+------+
| -- | BT | Wi-Fi | RAM | Variant | HV | Cert |
+--------+----+-------+------+---------+----+------+
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The main recipe already contains this file on the SRC_URI.
No need to append for every platform.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Add support based on v6.1.28 kernel version from STM release
openstlinux-6.1-yocto-mickledore-mp2-v23.12.06.
https://onedigi.atlassian.net/browse/DEL-8995
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Add support based on STM release openstlinux-6.1-yocto-mickledore-mpu-v24.06.26.
https://onedigi.atlassian.net/browse/DEL-8995
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Add open-source implementation of the OpenGL API support based on v23.0.3
version from STM release openstlinux-6.1-yocto-mickledore-mpu-v24.06.26.
https://onedigi.atlassian.net/browse/DEL-8995
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Add GPU support based on v6.4.15 version from STM release
openstlinux-6.1-yocto-mickledore-mpu-v24.06.26.
https://onedigi.atlassian.net/browse/DEL-8995
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Add support based on v2.8 version from STM release
openstlinux-6.1-yocto-mickledore-mp2-v23.12.06.
https://onedigi.atlassian.net/browse/DEL-8995
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Add support based on v3.19.0 version from STM release
openstlinux-6.1-yocto-mickledore-mp2-v23.12.06.
https://onedigi.atlassian.net/browse/DEL-8995
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Add initial support cloned from ccmp15, based on v2022.10 from STM release
openstlinux-6.1-yocto-mickledore-mp2-v23.12.06.
https://onedigi.atlassian.net/browse/DEL-8995
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commits adds the CCMX91 platform to the DEY
build system. Furthermore, it creates generic ccimx9
support to be used for the CCiMX91 and CCiMX93
platform.
https://onedigi.atlassian.net/browse/DEL-9106
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
When TrustFence is enabled, use the HUK programmed on the OTP
bits for the ccmp15 platform.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-9121
When running the installation script on variants with larger NANDs, two of the
script's commands take longer than our intended timeouts under specific
circumstances:
* When the variant has a NAND with 512 MiB or more and singlemtdsys is set
to "yes", running ubivolscipt takes longer than our 10 second timeout.
The larger the NAND storage size, the longer this command takes.
* When the variant has a 1 GiB NAND, singlemtdsys is set to "yes" and
dualboot is set to "no", the update of the recovery UBI volume takes
longer than our 15 second timeout.
In both of these cases, the script fails and the installation process cannot
continue. Apply the following changes to prevent this:
* Increase the ubivolscript timeout from 10 seconds to 30
* Increase the recovery update timeout from 15 seconds to 20
Also, remove the command immediately before ubivolscript is run, since said
command is already being run at the beginning of ubivolscript.
https://onedigi.atlassian.net/browse/DEL-9097
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
By default, the secure storage path in the REE is "/var/lib/tee". It is
part of the rootfs, and thus, it gets lost on a firmware update.
This commit changes that path to a different partition "/mnt/data/tee"
when Trustfence file-based encryption is enabled.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Building Optee trusted applications (TA) depends on optee_client and the TA
devkit provided by optee_os. Our toolchain provides those dependencies, but
the SDK script which configures the environment for standalone building,
is not configuring some variables needed to build trusted applications.
This commit extends the SDK environment script to allow building TAs.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Occassionally, the loading the WiFi driver might fail, because of the
MMC node was not correctly initialized.
Fix that by rebinding the MMC node. This fix implements a similar workaround
as in c30b947408.
https://onedigi.atlassian.net/browse/DEL-9083
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
One of the conditions used to determine the U-Boot file was missing its
terminator, breaking the script.
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
(cherry picked from commit 26dc437a25)
On devices with NAND as storage media, a post install script
modifies the fw_env.config file basing on the NAND geometry.
This only happens once after deployment, typically on production
environments. If the power is removed soon after the post install
script runs (which is a normal procedure on manufacturing
environments), there are chances that pending file system
operations have not been flushed, which may occasionally lead
to the fw_env.config file end up empty on the next reboot.
This commit adds a sync at the end of the post-install script
to guarantee the changes are written to the file system.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-9059
There is a corner case that wasn't cover by the script, if you
use the script using a -k -t the "-t" would be the name of the
dek.bin.
This new implementation solves the issue.
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
By default is trying to install an artifact imx-boot--<platform>
if trustfence is not enabled.
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
Some variables in the script belong to u-boot, not to the shell
running the script. Escape those variables so the shell does not
expand them.
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
This commit removes the Cortex-M4 overlay because the M4 has
been enabled now in the DTSI file.
https://onedigi.atlassian.net/browse/DEL-9056
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
The patches have been backported from the lf-6.1.36-2.1.0 release of
imx-mkimage.
https://onedigi.atlassian.net/browse/DUB-1081
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
The patches have been backported from the lf-6.1.36-2.1.0 release of
imx-mkimage.
https://onedigi.atlassian.net/browse/DUB-1081
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit adds some basic TSN support to DEY.
It includes the kernel configuration fragment with
the IEEE 802.1 support and the some user space tools
necessary to configure the network.
https://onedigi.atlassian.net/browse/DEL-9026
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
The command trustfence update doesn't require the partition argument.
Besides of that, remove extra fi on the cc8m platforms.
Signed-off-by: Francisco Gil <francisco.gilmartinez@digi.com>
* Move Digi code out of the upstream files to minimize conflicts in
version migrations.
* Remove all the TEE client copied code and use the libteeclient library.
* Some fixes in the Optee-based environment encryption
* Some simplifications in CAAM-based environment encryption.
https://onedigi.atlassian.net/browse/DUB-1079
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
At the moment, this overlay adds RTC calibration to compensate
the drift observed in the 32kHz input frequency of hardware
version 1 of the SOM.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
https://onedigi.atlassian.net/browse/DEL-8987
Update BDF file used on CC8MN and CC8MM with a new calibration
(GOLDEN3) to obtain a flatter frequency response and a better EVM
performance.
Reference calibration file is obtained from 'qca6574au-le-2-2-2_qca_oem'
repo at tag 'r00005.1' under path
'wlanfw/cnss_proc/wlan/fw/target/sdio_dst/qc6174/bdwlan30.bin'
(MD5SUM: 8a40d95698825e1718bee640b1f7982a).
Target output powers tables and CTL tables remain intact.
Changes required to pass the EN 300 328 V2.2.2 blocking test also remain
intact.
New BDF file:
- bdwlan30_US.bin (86180198440e6ab53734aabf0112c6ba)
https://onedigi.atlassian.net/browse/DEL-9001
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
This commit adds RT functionality to CCMP1. The patches
have been extracted from STM RT expansion package and
includes the maineline RT patches and the STM RT driver
patches and RT Kernel defconfig changes.
https://onedigi.atlassian.net/browse/DEL-8880
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
This commit adds RT functionality to the CCiMX93
platform. The patches have been extracted from the
NXP real time edge BSP and include the maineline RT
patches and the NXP RT driver patches and RT Kernel
defconfig changes.
https://onedigi.atlassian.net/browse/DEL-8881
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
Use the generic sys class to check if a mtd device is attached.
The virtual node may not be present in some kernel versions.
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
This commit fixes u-boot Trustfence naming for signed and
encrypted images used in the installation script removing
the a duplicated dash in the u-boot name.
https://onedigi.atlassian.net/browse/DEL-8271
Signed-off-by: Mike Engel <Mike.Engel@digi.com>
Optee-client provides the TEE Client API as defined by the GlobalPlatform TEE standard.
It is required to communicate with a Trusted Application (TA) running in a Trusted OS.
https://onedigi.atlassian.net/browse/DEL-8970
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Several things were wrong after the latest update to version 4.0: the
tee-supplicant path, some settings in the systemd unit, etc.
This commit fixes the installation so the optee test suite completes again.
https://onedigi.atlassian.net/browse/DEL-8989
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This commit fixes the set_fip_sign_key() function to match the new keys format
where there is a key_pass file for each key, no longer needing to search with
the key index.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit fixes a race condition where, if you have an existing PKI tree with
the new format (one key_pass file for each key), the script detects that the
PKI tree is incomplete because it is always trying to find the key_pass.txt
file with the old format. This commit adds an additional validation step to
verify the new keys format.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Add a check on the existence of the "temp-fitimg-loaded" environment
variable before setting it. It is needed, as with encrypted FIT images,
we need to decrypt them before accessing the boot script. In such cases,
u-boot sets that variable to "no" so the boot script does not override it,
and the FIT image is loaded again before the final boot to the OS.
https://onedigi.atlassian.net/browse/DEL-8945
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
The signing tools have a dependency of libQt5Core.so.5, which implies that this
library must to be installed on the native PC. This commit includes all the
required shared libraries for the signing tools inside the own package to avoid
external dependencies. With this change there is not needed any more the qtbase
dependency at build time.
Package version has been bumped to 1.2.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit fixes the set_fip_sign_key() function to match the new keys format
where there is a key_pass file for each key, no longer needing to search with
the key index.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit fixes a race condition where, if you have an existing PKI tree with
the new format (one key_pass file for each key), the script detects that the
PKI tree is incomplete because it is always trying to find the key_pass.txt
file with the old format. This commit adds an additional validation step to
verify the new keys format.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
- For Qualcomm QCA65x4 platforms:
Add support to create the 'World' board data file for the QCA65x4 Wi-Fi
chip to operate on World regulatory domain.
Kernel wireless driver already supports selecting the correct file based
on the configured Regulatory Domain via Kernel command line argument
'wlan.regdmn', which allows the following parameters:
* "US", for U.S.A. (default)
* "World", for worldwide
- For Murata type2AE platforms:
Add World CLM blob file for the wireless interface and JRL hcd file for
the Bluetooth interface. Also add the autocountry ininitialization script
and systemd service.
World CLM blob file:
- cyfmac4373-sdio_World.clm_blob (1abe7f3fa86d4123b0586cbbf0ec91ac)
Kernel wireless and bluetooth drivers already support selecting the correct
files based on the configured Regulatory Domain via Kernel command line
arguments 'brcmfmac.regdmn' and 'btbcm.regdmn' respectively, which allow the
following parameters:
'brcmfmac.regdmn':
* "US", for U.S.A. (default)
* "World", for worldwide
'btbcm.regdmn':
* "FCC.CE", for U.S.A., Europe and the rest of the world (default)
* "JRL", for Japan
https://onedigi.atlassian.net/browse/DEL-8905
Co-authored-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Different mechanisms are used to sign FIT images on the ccmp1 platforms and the
ccimx93, and we manage each mechanism via a different variable. The variable
names don't really reflect which platform they affect, which makes maintenance
harder.
Rename the variables so that it's easier to identify the platforms/vendors they
affect:
* Replace TRUSTFENCE_FIT_IMG with TRUSTFENCE_SIGN_FIT_STM
* Replace TRUSTFENCE_SIGN_FIT_ARTIFACT with TRUSTFENCE_SIGN_FIT_NXP
Don't rename TRUSTFENCE_FIT_IMG_SIGN_KEYNAME
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
Unless we have a use case in which we need to apply these fragments separately,
we can merge them both into a single fragment.
https://onedigi.atlassian.net/browse/DEL-8946
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This logic was fixed in commit e915a14b4b, so we
no longer have to manually copy the bootscript to generate FIT images.
https://onedigi.atlassian.net/browse/DEL-8946
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
We rely on FIT support to implement boot artifact authentication on ccmp1
platforms, but our implementation made it impossible to enable FIT support
outside of the context of Trustfence/secure boot.
Change this so that it's possible to enable FIT support without having to sign
the FIT artifacts. Also, modify the linux-dey 5.15 recipe so that the U-Boot
DTBs with signatures get copied only when FIT signing is enabled.
https://onedigi.atlassian.net/browse/DEL-8946
Signed-off-by: Gabriel Valcazar <gabriel.valcazar@digi.com>
This commit updates the required firmware binaries for Bluetooth and Wireless
interfaces, hostapd and wpa_supplicant recipes based on the Cypress Linux WiFi
Driver (FMAC) release v5.15.58-2023_1128 (Wireless firmware v13.10.246.334).
This change also includes a custom defconfig file for the hostapd and
wpa_supplicant recipes including the changes from the patches and the Digi
customizations.
Also are updated the Murata firmware repositories to match with the latest
Murata release imx-kirkstone-hedorah_r1.0, which is based in the same Cypress
Linux Wifi Driver release v5.15.58-2023_1128.
https://onedigi.atlassian.net/browse/DEL-8667
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
The standard string split() function does not support splitting a string
by spaces but preserving quoted strings, so it does not work for build
options disabling functionality, as they have this format:
"# CONFIG_OPTION is not set"
On the other hand, the "shlex" module provides a split function that
allows splitting strings by spaces and, at the same time, preserves
quoted strings.
In Trustfence, we need this functionality to disable default options that
would allow the booting of non-authenticated images.
https://onedigi.atlassian.net/browse/DEL-8704
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
The script to sign the boot artifacts lacked the support to configure the
revocation mask. The at-the-moment supported platforms did not need it,
but the ccimx93 does need it, so implement it in this commit.
https://onedigi.atlassian.net/browse/DEL-8704
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
With the introduction of the ccimx93 support in the following commits, the
srktool parameters not only differ for HAB/AHAB devices but also between
devices using AHAB (for example, different parameters for ccimx8x and
ccimx93). Thus, move this information to the platform-specific data table.
https://onedigi.atlassian.net/browse/DEL-8704
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
It is a cosmetic change, as there is no change in functionality, but
convert the if..elif..fi structure to a table with the platform-specific
data, so it's easier to maintain and extend.
https://onedigi.atlassian.net/browse/DEL-8704
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
expand the docker defconfig excerpt to add more default options, as some
of them might be enable in some platform defconfigs but not in other ones,
so just set all of them, as it is safe, and nothing happens if they are
already set in the original default defconfig.
To check if all LXC/docker options are enabled for a kernel,
run lxc-checkconfig in the system.
https://onedigi.atlassian.net/browse/DEL-8924
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
When we use a fitImage kernel type, all the boot artifacts are inside the
FIT image, so there is no need to add them to the boot image additionally.
We were using TRUSTFENCE_FIT_IMG to do this filtering, which uses
a fitImage kernel type underneath. This commit uses KERNEL_IMAGETYPE
instead, as this way, we can use kernel FIT images out of Trustfence and
still prevent polluting the boot images with not-needed artifacts.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
Other recipes may access SYSROOT_DIRS content by adding a dependence
on do_populate_sysroot.
We need this specific directory for the kernel fitImage support.
Signed-off-by: Javier Viguera <javier.viguera@digi.com>
This update fixes an initialization issue with devices without HWID programmed.
https://onedigi.atlassian.net/browse/DUB-1066
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit fixes a build issue when this script is installed but not shipped
in the u-boot-tools package.
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Not only install the US but all the FW files.
Apart of that, some scripts need a little adjustement such as:
* Modify the BT baudrate to 3Mbps for EU power configuration, as it is the
baudrate used by the btnxpuart driver.
* Replace the way to reset the interface on each hcitool command to
avoid missleading BT behaviour.
https://onedigi.atlassian.net/browse/DEL-8458
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
This commit implements the support to sign the different memory configurations for
the CCMP1 platforms, when trustfence is enabled, using FIT images.
https://onedigi.atlassian.net/browse/DEL-8752
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
This commit implements the support to allow different memory configurations for
the CCMP1 platforms, adding support to 512MB and 1GB memory variants for the CCMP15.
https://onedigi.atlassian.net/browse/DEL-8752
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Command 'bootz' allows boot unsigned Linux zImages, so disable it when secure
boot is enabled using FIT images.
https://onedigi.atlassian.net/browse/DEL-8769
Signed-off-by: Arturo Buzarra <arturo.buzarra@digi.com>
Replace the US-only default CLM blob with the latest one, generated by
Infineon based on the results from Digi Certification of the CCMP1.
New file:
- cyfmac4373-sdio_US.clm_blob (92225a8bccf0c7c9d7df6cdd64670fa1)
https://onedigi.atlassian.net/browse/DEL-8598
Signed-off-by: Gonzalo Ruiz <Gonzalo.Ruiz@digi.com>
Some minor fixes:
* return error code if installation fails
* cosmetic: update comment with options
* just exit after error and do not execute boolimit command
Signed-off-by: Isaac Hermida <isaac.hermida@digi.com>
Gonzalo Ruiz
Hector Palacios
Gabriel Valcazar
Isaac Hermida
Arturo Buzarra
Javier Viguera
Mike Engel
Francisco Gil